® HS2000 Series High Security Enclosures Installation/Operation Manual C494M-D (1/96) Pelco • 300 W.
TABLE OF CONTENTS Section Page 1.0 WARNINGS ..................................................................................................................................... 1 2.0 SCOPE ............................................................................................................................................ 2 3.0 DESCRIPTION ................................................................................................................................ 2 3.1 MODELS ..............
INSTALLATION/OPERATION MANUAL HS2000 SERIES HIGH SECURITY ENCLOSURE 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 4. The camera and lens combination shall not exceed 20 lbs (9.06 kg). 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 5.
2.0 SCOPE 3.1 MODELS The information within this manual covers the installation of the HS2000 High Security Camera Enclosure. HS2000 High security corner mount enclosure designed to fit flush with the ceiling. For use in applications such as elevators, parking garages, classrooms, offices, detention cells, etc., requiring maximum protection from vandalism in an unobtrusive package. HS2000/BR Same as HS2000 except brass plated finish. HS2000/CH Same as HS2000 except chrome plated finish. 3.
4.0 INSTALLATION 4.2 MID-WALL MOUNTING Before installing the HS2000 to a wall, make certain that the mounting surface is able to support the full weight of the enclosure plus the camera and lens. To mount the HS2000 enclosure mid-wall, use the optional hood, HS2000H, and perform the following steps: 1. Determine the position for the hood. Using it as a template, mark and drill holes in the mounting surface. 2. Attach the hood with the required fasteners (minimum 3/8" diameter recommended). 3.
4.4 TAMPER SWITCH INSTALLATION 5.0 CARE AND MAINTENANCE The HS2000 enclosures come standard from the factory with a tamper switch installed. Should it become necessary to install a replacement switch, refer to Figure 1 for the correct position of the bracket/switch and perform the following steps: Maintenance performed at regularly scheduled intervals will help prolong the operational life and appearance of the equipment. 1. Remove the front cover. 2.
HS2000 Mounting Template Pelco Manual C494M-D (1/96) 5
(This page intentionally left blank.
6.0 EXPLODED ASSEMBLY DIAGRAM Figure 2. HS2000 Exploded Assembly Diagram 7.0 MECHANICAL PARTS LIST FOR HS2000 ENCLOSURE Item No. Qty 1 2 3 4 1 1 1 1 5 6 7 8 9 A B C D E F G H I J 1 1 1 1 1 2 1 2 2 2 4 7 4 4 1 Description Bracket, Switch, Break-In Window, 8" x 7" x .
8.0 SPECIFICATIONS ELECTRICAL MECHANICAL Window: Camera Mounting: Maximum Camera/Lens Size: 1/4" (6.35 mm) thick impact and abrasion resistant clear Lexan Cable Entry: Access through back and top Tamper Switch: 1/4" (.63 cm) quick connect. N.O./ N.C. clearly marked on switch body. 10A, maximum switching current 125V, maximum switching voltage. Adjustable tilt table Accepts camera/lens combinations (including BNC connector) up to: 3.0" H x 3.0" W x 6.0" L (7.62 cm x 7.62 cm x 15.
9.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one (1) year after the date of shipment. • • • Six (6) months on all pan and tilts, scanners or preset lenses used in continuous motion applications (e.g., preset scan, tour and auto scan modes). Two (2) years on Legacy®, Intercept® and CM8500/ CM9500/CM9750 Matrix products.
® Pelco 300 West Pontiac Way Clovis, CA 93612-5699 USA (559) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (559) 292-3827 DataFAX (800) 289-9108 or (559) 292-0435 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.
