I N S T A L L A T I O N HS2000 High Security Enclosure C494M-E (9/06)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Option . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco. 4. The camera and lens combination shall not exceed 20 lb (9.06 kg). 5.
Description The HS2000 high-security camera enclosure is designed for indoor corner mount installation in such settings as elevators, parking garages, classrooms, offices, and detention cells requiring maximum protection from vandalism in an unobtrusive package. It fits flush to the ceiling in a corner. An impact-resistant clear Lexan® polycarbonate resin thermoplastic window is supplied, and an optional smoked window is available.
Installation Before installing the HS2000 to a wall, make sure that the mounting surface is able to support four times the full weight of the enclosure, camera, and lens. The tilt table and tilt table mounting brackets may be removed to provide adequate clearance for mounting the enclosure. NOTE: The four fasteners required to secure the HS2000 to a wall (minimum 3/8” diameter recommended) are not supplied. To mount the enclosure to a wall (tight to the ceiling), perform the following steps: 1.
REPLACEMENT TAMPER SWITCH INSTALLATION The HS2000 enclosure comes with a tamper switch installed. If you need to install a replacement switch, refer to Figure 1 for the correct position of the switch and perform the following steps: 1. Remove the front cover. 2. Install the switch and secure with lock washers and nuts. TAMPER SWITCH WIRING The tamper switch comes with normally open and normally closed contacts.
Maintenance Maintenance performed at regularly scheduled intervals will help prolong the operational life and appearance of the equipment. Clean the window with a mild nonabrasive detergent in water and a soft cloth regularly to help maintain picture clarity. For a heavily soiled window, use vinyl cleaner. SERVICE MANUAL If you need to repair the camera enclosure, obtain a service manual in one of the following ways: 8 • Go to Pelco’s we site at www.pelco.com and find service manual C494SM.
Exploded Assembly Diagram Figure 2. HS2000 Exploded Assembly Diagram Table A. Mechanical Parts List Item No. A B C D E F G H I J C494M-E (9/06) Qty 1 1 1 1 1 1 1 1 1 2 1 2 2 4 11 4 1 2 2 Description Bracket, switch, break-in Window, 8" x 7" x 0.
Specifications Mechanical Camera Mounting Adjustable tilt table Maximum Camera/Lens Size Accepts camera/lens combinations (including BNC connector) up to 3.0" H x 3.0" W x 6.0" L (7.62 x 7.62 x 15.24 cm) Enclosure Mounting Four 0.390-inch (0.99 cm) diameter holes on protected rear surface Security Tamper-resistant screw; N.O./N.C. switch contact on cover Tamper Switch Plunger type door switch with “pull to cheat” feature. N.O./N.C. contacts clearly marked on body of switch.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Genex ® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
