Manual

ManualsBrandsPelco ManualsFiber Optic Transmission1 Channel ST with Bidirectional Data, Single Mode

C5633M / REV 09-07-12

Tech SupporT: (800) 289-9100 InTernaTIonal: +1 (559) 292-1981

INSTALLATION AND OPERATION MANUAL

FTV/FRV10D1(M,S)1(ST,FC) Series

10-BIT DIGITALLY ENCODED VIDEO WITH “UP-THE-COAX”

EXTENDED DISTANCE OR BI-DIRECTIONAL DATA

(RS232, RS422 RS485 2/4W)

The FTV/FRV10D1(M,S)1(ST,FC) series transmits 10 bit digital video and

full duplex data over one Singlemode or Multimode fiber. The video supports

NTSC, PAL and SECAM CCTV camera systems. The data supports RS232,

RS422 and RS485 (2W & 4W) at data rates up to 115 Kbps (NRZ). The FTV/

FRV10D1(M,S)1(ST,FC) series also supports “Up-the-Coax” control signals

for Pelco Coaxitron. The product is “Plug-and-Play” with no electrical or optical

adjustments.

The FTV/FRV10D1(M,S)1(ST,FC) series allows the user to choose

bi-directional data or up-the-coax data through a switch on the unit, as

described in Figure 5 on Page 4.

Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining

equipment operating status. Figure 6 on Page 4 describes the LED indicators

for each light on the unit.

These units are interchangeable between stand-alone or card mount

configurations. See Figure A on Page 6 for installation instructions.

See Figures 1 – 7 for complete installation details.

Summary of content (8 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL FTV/FRV10D1(M,S)1(ST,FC) Series 10-bit digitalLY ENCODED video with “UP-THE-COAX” EXTENDED DISTANCE OR bi-directional data (RS232, RS422 RS485 2/4W) The FTV/FRV10D1(M,S)1(ST,FC) series transmits 10 bit digital video and full duplex data over one Singlemode or Multimode fiber. The video supports NTSC, PAL and SECAM CCTV camera systems. The data supports RS232, RS422 and RS485 (2W & 4W) at data rates up to 115 Kbps (NRZ).
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
PAGE 3
INSTALLATION AND OPERATION MANUAL FTV/FRV10D1(M,S)1(ST,FC) MULTIMODE OR SINGLE MODE OPTICAL FIBER VIDEO IN 0D1S1ST IDEO SMITTER + AY DATA / he COAX IN/OUT OPTICAL FIGURE 1 – FTV/FRV10D1(M,S)1(ST,FC) Series TRANSMITTER AND RECEIVER DATA NK OUT ON 422 A IN 485 EO 232 DOUT DIN GND DIN+ DINDOUT+ DOUTA B 12 PWR BLACK BLACK WITH WHITE STRIPES Power Supply: Surface Mount: 9 VDC @ 2W Rack Mount: From Rack NOTE: Remove Electrical Connector for Rack Mount Units FIGURE 2 – TRANSMITTER FIGURE 3 – R
PAGE 4
INSTALLATION AND OPERATION MANUAL FTV/FRV10D1(M,S)1(ST,FC) FIGURE 4 – DATA CHANNEL CONNECTIONS FTV10D1S1ST VIDEO TRANSMITTER + 2 WAY DATA / UP the COAX LINK VIDEO FIGURE 5 – SWITCH POSITIONS DATA The modeIN for each data channel is configured using a pair of switches on the front panel of the unit.
PAGE 5
INSTALLATION AND OPERATION MANUAL FTV/FRV10D1(M,S)1(ST,FC) FIGURE 7 – DATA CONNECTIONS Customer Equipment UTC Control Receiver VIDEO IN VIDEO OUT Transmitter Receiver Data Transmit DIN DOUT Data Receive Data Receive DOUT DIN Data Transmit Signal Ground GND GND Signal Ground Data Out (+) DIN(+) DOUT(+) Data In (+) Data Out (–) DIN(–) DOUT(–) Data In (–) Data In (+) DOUT(+) DIN(+) Data Out (+) Data In (–) DOUT(–) DIN(–) Data Out (–) Data Out (+) DIN(+) DOUT(+) Data In (+
PAGE 6
MECHANICAL INSTALLATION INSTRUCTIONS Installation Considerations This fiber-optic link is supplied as a Standalone/Rack module. Units should be installed in dry locations protected from extremes of temperature and humidity.
PAGE 7
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
PAGE 8
www.pelco.