I N S T A L L A T I O N FT8308/FR8308 Fiber Transmitter and Receiver Eight-Channel Digitally Encoded Video C1647M-A (6/06)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. C1647M-A (6/06) CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Product Overview DESCRIPTION The FT8308/FR8308 fiber transmitter and receiver provide the ability to transmit up to eight composite video channels over one optical fiber (refer to Figure 1). EIGHT VIDEO OUTPUTS EIGHT VIDEO INPUTS FT8308 TRANSMITTER ONE FIBER FR8308 RECEIVER Figure 1.
MODELS The FT8308/FR8308 fiber transmitter and receiver consist of the following series of models: Multimode Models:* FT8308MSTR Eight-channel fiber optic video transmitter; multimode, ST connector FR8308MSTR Eight-channel fiber optic video receiver; multimode, ST connector Single-Mode Models:* FT8308SSTR Eight-channel fiber optic video transmitter; single-mode, ST connector FR8308SSTR Eight-channel fiber optic video receiver; single-mode, ST connector FT8308SFCR Eight-channel fiber optic video tra
FRONT PANEL The front panel of the FT8308 transmitter and the FR8308 receiver provides LED indicators that allow you to monitor signal status, laser status (transmitter only), and operating power. The following sections provide a view of the front panel of the FT8308 transmitter and the FR8308 receiver. FRONT PANEL - FT8308 TRANSMITTER Figure 2 illustrates the front panel of the FT8308 transmitter. 8 4 7 3 6 2 5 1 Figure 2.
FRONT PANEL - FR8308 RECEIVER Figure 3 illustrates the front panel of the FR8308 receiver. 8 4 7 3 6 2 5 1 Figure 3. Front Panel of FR8308 Receiver VIDEO PRESENT LEDs 1-8 OPTIC FAULT LED, optical signal status indicator POWER LED (Pelco badge) For detailed information about the front-panel indicators, refer to the Troubleshooting section.
REAR PANEL Connections to the FT8308 transmitter and the FR8308 receiver are made to the rear panel of the modules. The following sections provide a view of the rear panel of the FT8308 transmitter and the FR8308 receiver. REAR PANEL - FT8308 TRANSMITTER Figure 4 illustrates the rear panel of the FT8308 transmitter. 8 7 6 5 Figure 4.
REAR PANEL - FR8308 RECEIVER Figure 5 illustrates the rear panel of the FR8308 receiver. 8 7 6 5 Figure 5.
Installation PACKAGE CONTENTS The following items are supplied: 1 FT8308 transmitter or FR8308 receiver 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4-40 x 0.
MOUNTING THE TRANSMITTER/RECEIVER TO A WALL The FT8308 transmitter/FR8308 receiver can be mounted to a wall in the following ways: • Using the supplied wall clip for attachment of a single module to a wall. For installation instructions, refer to the Mounting the Transmitter/Receiver Using the Wall Clip section below. • Using the optional WM5002 wall mount kits, which are designed for mounting of doublewidth fiber optic modules. The WM5002-3U base kit allows mounting of a single module to a wall.
UPPER FLANGE VERTICAL MOUNTING HOLE (2) HORIZONTAL MOUNTING HOLE (2) TRANSMITTER/ RECEIVER SCREW, PHILLIPS PAN HEAD WITH LOCK WASHER (2) WALL CLIP LOWER FLANGE Figure 6.
CONNECTIONS Connections to the FT8308 transmitter and the FR8308 receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTES: – A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a stand-alone module. A 12 VDC power supply is provided. If a 24 VAC power supply is used, the power supply must be a Listed Direct Plug-In Power Unit marked as Class 2 and rated as 24 VAC, 500 mA (minimum output).
Troubleshooting LED indicators on the front panel of the FT8308 transmitter/FR8308 receiver (refer to Figure 2 and to Figure 3, respectively) allow you to monitor signal status, laser status (transmitter only), and operating power. Table A provides information about the front-panel indicators and associated troubleshooting guidelines. Table A. Troubleshooting with Front-Panel Indicators Indicator Color Meaning Possible Cause Corrective Action Power LED (Pelco badge) Blue Pelco logo lights.
Table A. Troubleshooting with Front-Panel Indicators (Continued) Indicator Color Meaning Possible Cause Corrective Action Video Present LED (Continued) Red on receiver Incoming video signal is not present on the channel. Optical signal is not being received from the transmitter. Optic Fault LED is also red. Refer to the Optic Fault LED Receiver section in this table. Video source is not powered on. Check power connection to the video source. Video source is not connected to the transmitter.
Table A. Troubleshooting with Front-Panel Indicators (Continued) Indicator Color Meaning Possible Cause Corrective Action Optic Fault LED - Receiver Green The optical signal is being received from the transmitter. Red The optical signal is Transmitter is not powered not being received on. from the transmitter. — Fiber optic cable is not connected. No action required. Check power connections. Replace power supply if necessary. Check fiber optic connections.
Specifications VIDEO Number of Channels Modulation Type Video Input (FT8308)/ Video Output (FR8308) Bandwidth Gain Crosstalk Differential Gain Differential Phase Tilt Signal-to-Noise Ratio GENERAL Operating Temperature Input Power Requirements LED Indicators Dimensions Unit Weight MECHANICAL Connectors Video Rack Power/Alarm Stand-Alone Power Fiber Optic 20 8 Pulse code modulation, 8-bit resolution 1.0 Vp-p, 75 ohms; NTSC, PAL, and SECAM 6.5 MHz Unity -50 dB typical at 3.58 MHz <1% <1.
OPTICAL POWER BUDGET, TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT Model No. Transmitter Compatible Receiver Wavelength Optical Power Budget Maximum Transmission Distance Laser Class 1 Limit* 1 km (0.6 mi)‡ <15.6 mW Multimode (62.5/125 µm) FT8308MSTR FR8308MSTR 1310 nm 20 dB† Single-Mode (9/125 µm) FT8308SSTR FR8308SSTR 1310 nm 20 dB 30 km (18.6 mi)§ <15.6 mW FT8308SFCR FR8308SFCR 1310 nm 20 dB 30 km (18.6 mi)§ <15.
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
