I N S T A L L A T I O N FR8302A Fiber Receiver Two-Channel Digitally Encoded Video C1649M (1/06)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. C1649M (1/06) CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules.
Product Overview DESCRIPTION The FR8302A fiber receiver provides the ability to accept two composite video channels over two optical fibers. The FR8302A receiver is compatible with the FT8301A transmitter and is also backward compatible with the FT8301 transmitter. Each of two transmitters can send a single independent video channel to one FR8302A receiver (refer to Figure 1).
MODELS The FR8302A fiber receiver consists of the following series of models: Multimode Models:* FR8302AMSTR-2 Two-channel fiber optic video receiver; multimode, ST connector; transmission distance up to 2 km; compatible with FT8301AMSTR, FT8301AMST, and FT8301MST transmitters FR8302AMSTRE-2 Two-channel fiber optic video receiver; multimode, ST connector; transmission distance up to 6 km (extended distance); compatible with FT8301AMSTRE, FT8301AMSTE, and FT8301MSTE transmitters Single-Mode Models:* FR8302
FRONT PANEL The front panel of the FR8302A receiver provides LED indicators that allow you to monitor signal status and operating power (refer to Figure 2). Figure 2. Front Panel of FR8302A Receiver VIDEO PRESENT LED (per channel) OPTIC FAULT LED (per channel) POWER LED (Pelco badge) For detailed information about the front-panel indicators, refer to the Troubleshooting section.
REAR PANEL Connections to the FR8302A receiver are made to the rear panel of the module (refer to Figure 3). Figure 3.
Installation PACKAGE CONTENTS The following items are supplied: 1 FR8302A receiver 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4-40 x .
NOTE: The WM5001 wall mount kits can be used with the WM5002 wall mount kits, which are designed for mounting of double-width fiber optic modules. If mounting a mix of single-width and double-width modules is desired, it is recommended that a maximum of two single-width modules and one double-width module be mounted in combination with one another. For mounting instructions using the wall mount kits, refer to the WM5000 Series Wall Mount Kit Installation manual.
CONNECTIONS Connections to the FR8302A receiver are made on the rear panel of the module and consist of the following: • Power connection NOTES: – A 12 VDC or 24 VAC power supply can be used to power the receiver when used as a standalone module. A 12 VDC power supply is provided. If a 24 VAC power supply is used, the power supply must be a Listed Direct Plug-In Power Unit marked as Class 2 and rated as 24 VAC, 200 mA (minimum output).
Troubleshooting LED indicators on the front panel of the FR8302A receiver (refer to Figure 2) allow you to monitor signal status and operating power. Table A provides information about the front-panel indicators and associated troubleshooting guidelines. NOTE: For troubleshooting information indicated by the LEDs on the associated FT8301A/FT8301 transmitter, refer to the manual supplied with the transmitter. Table A.
Table A. Troubleshooting with Front-Panel Indicators (Continued) Indicator Color Meaning Possible Cause Corrective Action Optic Fault LED Green The optical signal is being received from the transmitter. – No action required. Red The optical signal is not being received from the transmitter. Transmitter is not powered on. Check power connections. Replace power supply if necessary. Fiber optic cable is not connected. Check fiber optic connections.
Specifications VIDEO Number of Channels Modulation Type Video Output Bandwidth Gain Differential Gain Differential Phase Tilt Signal-to-Noise Ratio GENERAL Operating Temperature Input Power Requirements LED Indicators Dimensions Unit Weight MECHANICAL Connectors Video Rack Power/Alarm Standalone Power Fiber Optic 16 2 Pulse code modulation, 8-bit resolution BNC, 1.0 Vp-p, 75 ohms or UTP, 100 ohms; NTSC, PAL, and SECAM 6.
OPTICAL POWER BUDGET, TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT FR8302A Receiver Compatible Transmitters Wavelength Optical Power Budget Maximum Transmission Distance Laser Class 1 Limit* 2 km (1.2 mi)†† <0.78 mW Multimode (62.5/125 µm) FR8302AMSTR-2 FT8301AMSTR FT8301AMST FT8301MST 850 nm 20 dB† Multimode - Extended Distance (62.5/125 µm) FR8302AMSTRE-2 FT8301AMSTRE FT8301AMSTE FT8301MSTE 1310 nm 26 dB† 6 km (3.7 mi)†† <15.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex® Series products (multiplexers, server, and keyboard).
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
