INSTALLATION/OPERATION IX Series Network Camera Sarix™ Technology C2950M-E (8/10)
Contents Important Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Legal Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . .
Imaging Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Configuring the Orientation of the Scene. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Changing the Digital Processing Settings . . . . . . . . . . . . . . . . . . . . . . . .
List of Illustrations 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Camera Connections and Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Remove Back Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Notices LEGAL NOTICE SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS.
Introduction The IX Series camera is a network-based camera with a built-in, Web-based viewer for live streaming to a standard Web browser (Microsoft® Internet Explorer® or Mozilla® Firefox®). All camera models are preloaded with Pelco’s Camera Sabotage behavior, which can be configured and enabled using a standard Web browser.
ACT PRODUCT OVERVIEW 24V~ RELAY ALARM ACC RESET LINK PoE R1 A1 (FRONT COVER OPENED) F V Figure 1. Camera Connections and Features ì î ï ñ ó r s t u 8 RJ-45 Network Port: Connects the camera to the IP network. Also supplies power to the camera through the network using PoE. If PoE is not available, the camera is prewired for 24 VAC. Ethernet Activity LED: Flashes green to indicate that data is being transmitted or received by the camera.
~í ~â ~ä Auto Iris Lens Connector: Controls the amount of light allowed through the lens. Insert the 4-pin connector from the DC drive auto iris lens into this connector Auto Back Focus Button: Sets the auto back focus mechanism. Press the button once to center the auto back focus mechanism and to fully open the iris. Press and hold the button for three seconds to start the auto back focus mechanism and to focus the camera. NTSC/PAL Button: Toggles the service port between NTSC and PAL formats.
Installation NOTE: Megapixel lenses are designed and tested to deliver optimal image quality to megapixel cameras. A standard definition lens installed on a megapixel camera will limit the resolution of the camera and create poor image quality. 1. Install the lens. a. Remove the cover from the lens mount. b. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the lens and the imager.
4. For FCC Class B installations, attach the supplied ferrite to the network cable (refer to Figure 5.) The ferrite should be installed on the cable approximately 1 inch (2.54 cm) from the camera’s RJ-45 network port. Figure 5. Ferrite Installation WARNING: The ferrite must be installed for the camera to meet FCC Class B compliance standards. Failure to correctly install the ferrite might cause harmful interference to radio communications. 5.
SERVICE CABLE The camera includes a service port that outputs camera video. Use it at the installation site to set up the field of view and to focus the camera. Pelco offers an optional service cable (IX-SC) that connects directly to the service port. The service cable has a male BNC output for most standard viewers. NOTE: The ICS-SC and CST150 are not compatible with this camera.
WIRING CAT5 CABLE Connect a Cat5 cable to an RJ-45 network connector (not supplied). The 8-pin connector includes video and PoE for the camera. PoE (IEEE 802.3af) injects power over the same cabling that carries the network data, eliminating the need for a separate power supply. This simplifies the installation and operation of the camera without affecting network performance. NOTE: The camera will autosense and configure itself to use either a crossover cable or a straight cable.
ALARM, RELAY, AND 24 VAC CONNECTOR Single Camera Wiring If PoE is not available: 1. Connect the alarm, relay, and 24 VAC wires to the supplied mating connector (refer to Figure 8). NOTE: Only use the 24 VAC wires if PoE is not available. 2. When finished, attach the mating connector to the green connector on the back of the camera. Multiple Camera Wiring If you are operating the camera using 24 VAC and you are wiring more than one camera to the same transformer: 1.
Connecting Alarms The camera provides an alarm input for external signaling devices, such as door contacts or motion detectors. Both normally open and normally closed devices are supported. Supervised Alarms When an alarm is configured as a supervised alarm, the camera maintains a constant electrical current through the alarm circuit (3.3 VDC, 1 ohm). If the alarm circuit length changes, due to an electrical short or a bypass, the voltage fluctuates from its normal state and activates an alarm.
Unsupervised Alarms When an alarm is configured as an unsupervised alarm, the camera only activates an alarm when the normal alarm state (open or closed) changes. Figure 12 illustrates the alarm and no alarm conditions of an unsupervised alarm input. NORMALLY CLOSED NO ALARM GND NORMALLY OPEN +V NO ALARM GND +V ALARM GND +V ALARM GND +V ALARM GND +V NO ALARM GND +V +V ALARM GND CUT NO ALARM GND CUT +V BYPASS BYPASS Figure 12.
Operation CAMERA CONFIGURATION SEQUENCE Once the device is installed and power is applied, the device will start a configuration sequence: the green LED flashes five times per second for approximately two minutes and then glows solid green, indicating that the boot cycle is complete and the device is on line. NOTE: If the device is not connected to a Dynamic Host Configuration Protocol (DHCP) server and DHCP is enabled, the configuration sequence might take up to five minutes to complete.
ACCESSING THE IP CAMERA The first time you access the camera, the live video page appears. By default, you are viewing the video as a public user and only have access to the single stream live view. If, for security purposes, users should not be allowed to view video without first logging on to the camera, change the permissions for public users. LOGGING ON TO THE CAMERA 1. Open the Web browser. 2. Type the camera’s IP address in the browser address bar.
Live Video Page The live video page allows you to manage the way you view live video and capture images. You can also view live video from this page and access menus on the navigation bar (based on user permissions). Figure 15.
LIVE VIDEO PAGE ICONS Viewable icons are based on user permissions. Show Device List: Displays a list of viewable cameras connected to the same virtual local area network (VLAN) as the camera to which you are logged on. Disable Viewer: Closes the live view window. 1 x 1 Mode: Displays a single video pane. 2 x 2 Mode: Displays 4 video panes in rows of two. 3 x 3 Mode: Displays 9 video panes in rows of three. 4 x 4 Mode: Displays 16 video panes in rows of four.
SELECTING A STREAM 1. Click the Select Stream button. 2. Select one of the following stream options from the Select Stream page: Primary Stream: To select this stream, click the button next to Primary Stream. Secondary Stream: To select this stream, click the button next to Secondary Stream. QuickView Stream: To select this stream, click the button next to QuickView Stream. Event Stream: To select this stream, click the button next to Event Stream.
EVENT STREAM The Event Stream displays a list of alerts triggered by a running behavior (analytic). The alert includes a screen capture, the profile that was triggered, and the zone where the alert was detected. For the Event Stream to work you must have a behavior profile running. To set up and run behaviors, use the Analytic Configuration page located in the drop-down menu of the Events Tab. UNICAST A unicast transmission sends a separate video stream to each user that is requesting data.
Settings Page Depending on user permissions, the Settings page allows you to manage camera system settings, set up users, configure events, and control the camera. NOTE: The Settings menu might not be available if the user does not have permission to access this feature. ACCESSING THE CAMERA MENUS 1. Log on to the camera. 2. Click the Settings link in the navigation bar located in the upper-right corner of the page; a list of menu tabs appears. 3.
System Tab Use the System tab to change the device name, configure the time settings, set up the text overlay for the live view, and display system information. You can also use the System tab to generate a system log, reboot the camera, or to restore the camera's factory default settings. General Settings The General Settings page includes configurable fields for the device name, time server, and text overlay settings.
CONFIGURING THE TIME SETTINGS If the camera is connected to a Dynamic Host Configuration Protocol (DHCP) network that has time server properties configured, the camera will synchronize automatically with the time server. If the DHCP network’s time server properties are not configured or the network does not have a time server, you need to configure the DHCP settings manually. 1. Click the System tab. 2. Select General Settings from the drop-down menu. 3.
RESTORING ALL CAMERA DEFAULTS WARNING: This process cannot be undone; all user and custom settings will be lost. 1. Click the System tab. 2. Select General Settings from the drop-down menu. 3. Click the Restore All Camera Defaults button to restore the camera’s factory default settings. NOTE: If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) network, the IP address settings for the camera will be lost and the server will not recognize the camera.
Network Tab Use the Network tab to change the camera’s general network settings, select the Secure Sockets Layer (SSL) settings, enable Secure Shell (SSH), configure 802.1x port security, and select Simple Network Management Protocol (SNMP) settings. General Network Settings The General Network page includes configurable and read-only fields for network communication settings. Available settings include the Hardware Address, Hostname, IP Address, Subnet Mask, Gateway, and DNS Servers.
CHANGING THE HOSTNAME 1. Place your mouse pointer over the Network tab. 2. Select General from the drop-down menu. 3. Click in the Hostname box and highlight the text. 4. Type a user-friendly name into the Hostname box (1 to 21 characters) using any combination of alphanumeric characters. A user-friendly name makes it easier to recognize the device on the network. 5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.
SELECTING THE SECURE SOCKETS LAYER MODE Figure 16. SSL Configuration Page 1. Place your mouse pointer over the Network tab. 2. Select SSL from the drop-down menu. 3. Select one of the following modes: Required: A signed Secure Sockets Layer (SSL) certificate must be installed, and a secure URL that begins with the protocol name “https:” must be used to access the camera. Sensitive data is always encrypted during transmission.
GENERATING A CERTIFICATE REQUEST 1. Place your mouse pointer over the Network tab. 2. Select SSL from the drop-down menu. 3. Click the Install Certificate button located at the bottom of the SSL Configuration page. The Select Certificate Install Method option buttons appear on the page. 4. Select Generate Certificate Request, and then click Next. The Certificate Request Form opens. 5. Fill in all of the fields, and then click Generate Request.
ENABLING SECURE SHELL Figure 17. SSH Settings Page 1. Place your mouse pointer over the Network tab. 2. Select SSH from the drop-down menu. 3. Select the Enabled check box. NOTE: The username is always root and cannot be changed. The username and password are required when accessing the camera through a third-party SSH client. 4. Click in the Password box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive. 5. Click in the Re-type Password box and retype your password. 6.
SELECTING SNMP SETTINGS WARNING: The Simple Network Management Protocol (SNMP) settings are advanced controls. Consult your network administrator to obtain the required information to configure SNMP settings. 1. Place your mouse pointer over the Network tab. 2. Select SNMP from the drop-down menu. 3. Select the SNMP Version: None, V2c, or V3. None disables the SNMP configuration and is the default setting.
CONFIGURING SNMP V3 Figure 19. SNMP V3 Settings 1. Place your mouse pointer over the Network tab. 2. Select V3 as the SNMP Version. 3. Type the SNMP user name in the SNMP user field. 4. Select the encryption algorithm for authentication from the Authentication drop-down menu: None, MD5, or SHA. If you use authentication method MD5 or SHA, type a password in the text box to the right of the selected Authentication encryption. 5.
Imaging Tab Use the Imaging tab to change the camera’s general image settings, adjust the camera exposure, program the focus mechanism, adjust the tone map settings to increase scene detail, tune the white balance settings for scenes with fluctuating lighting conditions, or define window blanking privacy areas. General Imaging Settings General imaging settings include adjustments for camera orientation and digital processing.
Window Blanking Settings Window blanking is used to conceal user-defined privacy areas. A blanked area appears on the screen as a solid gray window. The camera can handle up to four blanked windows as long as the total blanked area does not exceed 50 percent of the field of view.
CHANGING THE DIGITAL PROCESSING SETTINGS Figure 21. Digital Processing Page 1. Place your mouse pointer over the Imaging tab. 2. Select General from the drop-down menu. 3. Select the mode: Manual or Auto. Auto is the default. 4. Move the slider to the left or right to change the following settings: Sharpness Adjust/Sharpness: Controls the clarity of detail in a scene. Move the slider to the right to increase the sharpness; move the slider to the left to decrease the sharpness.
SELECTING AUTO EXPOSURE SETTINGS Figure 22. Auto Exposure Page 1. Place your mouse pointer over the Imaging tab. 2. Select Exposure from the drop-down menu. 3. Select the Auto mode. 4. Select the Light Control method: Digital Exposure or Auto-Iris Exposure. Digital Exposure: This setting automatically adjusts the sensor exposure time depending on the light level at the scene.
5. Select the Exposure Optimization setting: Normal or Action. These are optimizations of the Digital Exposure control. Normal: This setting is for very bright scenes and exposure time is very short. As the scene becomes less bright, the exposure time is increased until the maximum exposure time is reached. Normal is the default setting. Action: This setting operates similar to Normal except the short exposure times are used for both bright and mid-level lighting.
SELECTING MANUAL EXPOSURE SETTINGS Figure 23. Manual Exposure Page 1. Place your mouse pointer over the Imaging tab. 2. Select Exposure from the drop-down menu. 3. Select the Manual mode. 4. Move the Analog Gain slider to the desired position. Increasing the gain increases the brightness of the image, but it also increases the amount of noise in the image. The analog gain range is 1.00 to 15.75; the default setting is 1.00. 5. Move the Exposure Time slider to the desired position.
DAY NIGHT SETTINGS The Day Night mode controls the position of the IR cut filter, which determines the color or black-white setting of the camera. The Day Night mode settings change depending on the Exposure settings. If the camera is set to Auto Exposure mode, the Day Night mode can be set to Auto or Manual and all of the respective settings are available.
CONFIGURING AUTO FOCUS SETTINGS Figure 24. Auto Focus Page 1. Place your mouse pointer over the Imaging tab. 2. Select Focus from the drop-down menu. 3. Select the Auto mode. 4. Set the Temperature Change Refocus setting. The camera is programmed to run a quick automatic focus sequence when the internal temperature sensor of the camera detects an environmental temperature change of 41°F (5°C). This focus sequence adjusts the center focal point of the scene to maintain optimal focus.
CONFIGURING MANUAL FOCUS SETTINGS Figure 25. Manual Focus Page NOTE: It is recommended to set the focus to Manual when using analytics. If the focus is set to Auto, significant background changes will occur when the camera automatically adjusts to different points within a scene resulting in frequently changing image sharpness. This may cause problems with scene recognition, which will suspend analytics operation or cause false alarms. 1. Place your mouse pointer over the Imaging tab. 2.
SETTING TONE MAP OPTIONS Figure 26. Tone Map Page 1. Place your mouse pointer over the Imaging tab. 2. Select Tone Map from the drop-down menu. 3. Select the Optimization setting: Normal (H.264): If the compression standard for the primary stream is H.264, set Optimization to Normal (H.264). This is the default setting. Photographic (JPEG): If the compression standard for the primary stream is JPEG, set Optimization to Photographic (JPEG). 4.
SELECTING AUTO WHITE BALANCE SETTINGS Figure 27. Auto White Balance Page 1. Place your mouse pointer over the Imaging tab. 2. Select White Balance from the drop-down menu. 3. Select the Auto mode. 4. Move the sliders to adjust the following settings in Auto mode: Red Gain Adjust: Adjusts the image output in the red range. Move the slider to the right to increase the red level; move the slider to the left to decrease the red level. As you move the slider, you will see the color change on your monitor.
SELECTING MANUAL WHITE BALANCE SETTINGS Figure 28. Manual White Balance Page NOTE: Manual white balance is recommended only for indoor applications that have a single, unchanging primary light source. 1. Place your mouse pointer over the Imaging tab. 2. Select White Balance from the drop-down menu. 3. Select the Manual mode. 4. Move the sliders to adjust the following settings in Manual mode: Red Gain: Adjusts the image output in the red range.
TURNING ON WINDOW BLANKING Figure 29. Window Blanking Page 1. Place your mouse pointer over the Imaging tab. 2. Select Window Blanking from the drop-down menu. 3. Select the On option for Window Blanking. 4. Draw a window in the Live Preview area of the page: a. Hold down the left mouse button. b. Drag the mouse diagonally across the area you want to blank. c. A color-coded box appears in the Edit Window section of the page that is the same color as the window drawn in the Live Preview area.
A/V Streams Tab Use the A/V Streams tab to configure the video and audio streams for the camera. The A/V Streams tab includes a Video Presets page, a Video Configuration page, and an Audio Configuration page. Video Presets The Video Preset page includes three fully-configured video presets, which include primary and secondary video stream settings for easy setup. These presets may also be used as a starting point for a custom video configuration. These preset configurations vary depending on camera model.
SELECTING A VIDEO PRESET CONFIGURATION Figure 30. Select Video Preset Configuration Page 1. Place your mouse pointer over the A/V Streams tab. 2. Select the Video Preset option from the drop-down menu. 3. Click the button next to the video preset stream configuration (High, Medium, or Low) that you want to select. 4. Click the Save button to save the settings, or click the Reset button to clear your selection without saving it.
CONFIGURING A CUSTOM VIDEO STREAM CONFIGURATION Figure 31. Custom Video Stream Configuration Page 1. Place your mouse pointer over the A/V Streams tab. 2. Select Video Configuration from the drop-down menu. 3. Click both of the Clear buttons to delete the primary and secondary streams settings. 4. Optional: In the Primary Stream section, type a user-friendly name in the Name box (2 to 64 characters). A user-friendly name makes it easier to recognize the stream (for example, Live and Recording). 5.
COMPRESSION STANDARDS JPEG: A commonly used video compression scheme, also known as MJPEG. JPEG has the least impact on the camera’s processor, but it requires the most bandwidth. MPEG-4 (available only with 0.5 megapixel model): A full-motion video standard used by most DVD recorders. MPEG-4 is less processor-intensive than JPEG, but it uses more bandwidth than H.264. H.264: A new version of MPEG-4 compression used in high-definition video players such as Blu-ray™ and HD-DVD. H.
BIT RATE The bit rate is the quality of the video stream (rendered in kilobits per second). The higher the value, the higher the video quality and bandwidth required. NOTE: When you change any of the video stream configuration settings, the camera automatically adjusts the bit rate. If you manually reduce the bit rate lower than the camera's automatic setting, the image quality might be reduced and the stream selection options might be limited.
SELECTING THE AUDIO CONFIGURATION SETTINGS To use audio with the camera you must have an audio device connected to the accessory port located on the back of the camera. Once the device is connected, audio can only be enabled through the primary stream. Audio and video may not be synced when viewing and listening to the primary stream through a Web browser. You may experience a three-second delay in video when viewing the primary stream with audio.
Users Tab Use the Users tab to create and manage user accounts and to change the way the camera manages the users settings. General Settings Use the general settings page to set the public user access level. This access level is a predefined set of user permissions that allow the camera to be accessed without logging on. The permission levels are Operator, Viewer, and Disabled. The General Settings page also allows you to change the way the camera manages users and groups settings.
SELECTING THE USERS AND GROUPS SETTINGS Figure 33. General Settings Page for Users WARNING: The Node and Mixed settings are advanced controls. Consult your network administrator to obtain the required information. 1. Place your mouse pointer over the Users tab. 2. Select General Settings from the drop-down menu. 3. Select an access level from the Public User Access Level drop-down menu. Disabled: The public user has no permissions and cannot access the live view page without a password.
CREATING A NEW USER Figure 34. Users Page 1. Place your mouse pointer over the Users tab. 2. Select Users from the drop-down menu. 3. Select the Access Level for the user. Admins: This user has access to all camera settings. Managers: This user has access to all settings except they cannot modify a user’s permissions or restore factory default settings. Operators: The permissions for this user are view video, PTZ functions, and API access.
EDITING A USER 1. Place your mouse pointer over the Users tab. 2. Select Users from the drop-down menu. 3. Click the user profile that you want to edit from the box on the left side of the page. 4. If required, select a different Access Level for the user. 5. Double-click in each of the text boxes to highlight the text. Type the new information in each text box. NOTE: The Username cannot be modified; this text box is read-only. 6.
Events Tab Use the Events tab to configure camera events and analytics. Events are activated by user-defined event sources that tell the device how to react when an event occurs. Event handlers are the actions that the device takes when an event occurs. For example, a system source can be configured to send email to an operator if the system shuts-down and restarts. Sources The camera supports one physical input alarm source, a system source, and a timer source.
SOURCES Figure 35. New Event Source Page An event is a preprogrammed camera function that is automatically activated by an event source. The camera supports the following types of event sources: Alarm Source: The camera supports one alarm source. The sources are the camera inputs for external signaling devices, such as door contacts or motion detectors. System Source: A system source is activated when the camera restarts. Timer Source: A timer source is a user-defined event.
CREATING A SYSTEM EVENT SOURCE 1. Place your mouse pointer over the Events tab. 2. Select Sources from the drop-down menu. 3. Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters). 4. Select System from the Type drop-down menu. 5. Select the Boot check box to activate an event when the camera reboots. 6. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it. CREATING A TIMER EVENT SOURCE 1.
HANDLERS Figure 36. New Event Handler Page Event handlers are the actions that the camera takes when an event occurs. The camera supports the following event handlers: Send Email: Sends an email to a defined email address when an event is activated. The Simple Mail Transfer Protocol (SMTP) server must be configured to accept the camera’s IP address. Write JPEG to SD Card: Saves a JPEG of the activated event to an SD card. An SD card must be installed in the device for this handler to function.
CREATING AN EVENT HANDLER: SEND EMAIL NOTE: To use email notification, the camera must be connected to a local area network (LAN) that maintains an SMTP mail server. Consult your network administrator for information on configuring email notification on your local network. 1. Configure the SMTP server to send email. 2. Place your mouse pointer over the Events tab. 3. Select Handler from the drop-down menu. 4. Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters). 5.
CREATING AN EVENT HANDLER: WRITE JPEG TO SD CARD 1. Install an SD card in the SD card slot located on the back of the camera. NOTE: The SD card must be formatted as FAT32. Other formats are not compatible with the camera. 2. Place your mouse pointer over the Events tab. 3. Select Handlers from the drop-down menu. 4. Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters). 5. Select “Write JPEG to SD Card” in the Type drop-down menu. 6.
CREATING AN EVENT HANDLER: OPEN/CLOSE RELAY 1. Place your mouse pointer over the Events tab. 2. Select Handlers from the drop-down menu. 3. Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters). 4. Select Open/Close Relay in the Type drop-down menu. 5. Move the On Time slider to set the amount of time that the relay will remain open. The time range is 0.1 to 200 seconds; the default setting is 0.1. 6.
EXAMPLE HANDLER FILTER SETUP If you do not want a handler activated every time an event occurs, use the filter fields to limit handlers. For example, you only want a handler activated when an event occurs after business hours. Your business is open Monday through Saturday, 8:00 a.m. to 6:00 p.m., and it is closed on Sunday. 1. Create a handler for Monday through Saturday: a. Select the day filter fields Monday through Saturday. b. Type 0000 in the Start box and 0800 in the End box. c.
ANALYTIC CONFIGURATION Figure 37. Analytic Configuration Page To configure the Camera Sabotage behavior using a standard Web browser, you must create a profile, activate the behavior, and select the behavior-specific settings for the profile. Camera Sabotage uses the following behavior-specific settings: Delay before alarm: Defines the delay between the time a violation is detected and the actual trigger of an alarm. If the violation stops within the delay period, no alarm is triggered.
CREATING A NEW PROFILE 1. Place your mouse pointer over the Events tab. 2. Select Analytic Configuration from the drop-down menu. 3. Click the plus button (+) located in the Select Profile section. 4. Type a descriptive name for the profile in the Name box located in the Profile Settings section. NOTE: Consider naming profiles based on their function. A more descriptive name makes it easier to recognize and locate a profile. 5.
Specifications IXS0 SERIES MODELS IXS0C SVGA 0.5 megapixel network color camera IXS0DN SVGA 0.
VIDEO Video Encoding H.264 base profile, MPEG-4, and MJPEG Video Streams Up to 2 simultaneous streams; the second stream is variable based on the setup of the primary stream Frame Rate Up to 30, 25, 24, 15, 12.5, 12, 10, 8, 7. 5, 6, 5, 4, 3, 2.5, 2, 1 (dependent upon coding, resolution, and stream configuration) Available Resolutions Resolution MPx 0.5 Supported Protocols Users Unicast Multicast Width Height Maximum IPS Aspect Ratio MJPEG H.264 Base Profile MPEG-4 4:3 30 25 N/A 800 600 0.
IX10 SERIES MODELS IX10C 1.3 megapixel network color camera IX10DN 1.3 megapixel network day/night camera GENERAL Imaging Device 1/3-inch (effective) Imager Type CMOS Imager Readout Progressive scan Maximum Resolution 1280 x 1024 Signal-to-Noise Ratio 50 dB Auto Iris Lens Type DC drive Electronic Shutter Range 1 ~ 1/100,000 sec Wide Dynamic Range 60 dB White Balance Range 2,000° to 10,000°K Sensitivity Color (33 ms) Color SENS (500 ms) Mono (33 ms) Mono SENS (500 ms) f/1.
VIDEO Video Encoding H.264 base profile and MJPEG Video Streams Up to 2 simultaneous streams; the second stream is variable based on the setup of the primary stream Frame Rate Up to 30, 25, 24, 15, 12.5, 12, 10, 8, 7. 5, 6, 5, 4, 3, 2.5, 2, 1 (dependent on the coding, resolution, and stream configuration) Available Resolutions Resolution MPx Supported Protocols Width Height Maximum IPS Aspect Ratio MJPEG H.264 Base Profile 5:4 20 8 1.3 1280 1024 1.2 1280 960 4:3 20 8 0.
IX30 SERIES MODELS IX30C 3.1 megapixel network color camera IX30DN 3.1 megapixel network day/night camera GENERAL Imaging Device 1/3-inch (effective) Imager Type CMOS Imager Readout Progressive scan Maximum Resolution 2048 x 1536 Signal-to-Noise Ratio 50 dB Auto Iris Lens Type DC drive Electronic Shutter Range 1 ~ 1/100,000 sec Wide Dynamic Range 60 dB White Balance Range 2,000° to 10,000°K Sensitivity Color (33 ms) Color SENS (500 ms) Mono (33 ms) Mono SENS (500 ms) f/1.
VIDEO Video Encoding H.264 base profile and MJPEG Video Streams Up to 2 simultaneous streams; the second stream is variable based on the setup of the primary stream. Frame Rate Up to 30, 25, 24, 15, 12.5, 12, 10, 8, 7. 5, 6, 5, 4, 3, 2.5, 2, 1 (dependent on the coding, resolution, and stream configuration) Available Resolutions Resolution Supported Protocols Maximum IPS MPx Width Height Aspect Ratio MJPEG H.264 Base Profile 3.1 2048 1536 4:3 10 3 2.1 1920 1080 16:9 15 6 1.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
www.pelco.com Pelco, Inc.