I N S T A L L A T I O N ® ExSite Series Explosionproof Pan and Tilt System C1302M-F (11/08)
C1302M-F (11/08)
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Methods of Installation . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the supply circuit before opening. Keep assembly tightly closed when in operation. 7. The maximum ambient temperature range is -76° to 140°F (-60° to 60°C). 8.
Getting Started Thank you for purchasing Pelco’s ExSite® Series explosionproof integrated positioning system. This manual includes instructions for installing all the components of the ExSite Series system. Once the system installation is complete, refer to the operation/programming manual shipped with the camera module for instructions on how to operate and program your system. METHODS OF INSTALLATION The system can be installed in a standard or inverted position.
Install the Power Module Attach the power module to the mounting surface. Use only installation methods and materials capable of supporting four times the maximum specified load of the system (220 lb/100 kg). NOTE: If required, install the optional TXB translator, fiber module, or UTP board before installing the power module. Refer to the installation instructions supplied with the TXB translator, fiber module, or UTP board for installation instructions.
CONNECT WIRING Refer to the following information to connect the wires and cables as required. WARNING: When installing this unit, provide access to the communication wires (TX+ and TX-) to allow connection to the system for future software upgrades. Connectors must be installed so that the integrity of the hazardous location is maintained. These communication wires are required even if the system uses Coaxitron® control. Maximum wire distance for RS-422 data wires is 4,000 ft (1,219 m).
DIP SWITCH SETTINGS Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these settings are located on the top of the power module. NOTE: No DIP switch settings are required for Coaxitron control. Figure 3 shows the default settings for the DIP switches. Refer to the following to configure the ExSite system settings. SW1-1 is set to the ON position. All other switches are set to the OFF position.
Table A.
Table B.
Table B.
Table B.
Install the Camera Module To install the camera module do the following: 1. Refer to Figure 4. Loosen the set screw at the back of the enclosure with the provided 1.5 mm Allen wrench. SET SCREW Figure 4. Loosen Set Screw 2. Use the supplied spanner wrench to loosen the back of the camera enclosure (refer to Figure 5). Once the back is loose, use your hands to continue to loosen it until it can be removed. WARNING: To avoid thread damage carefully remove the back of the camera enclosure.
3. Slide the camera module into the enclosure. Refer to Figure 6 to position the camera module properly in the enclosure. Carefully mate the camera’s power connector to the mating connector located inside the enclosure. Models with a wiper: The tab located inside the enclosure must be pointing down before installing the camera module (refer to Figure 6). To position the tab, place the wiper located at the front of the enclosure in the center of the viewing window (refer to Figure 7).
4. Refer to Figure 8 and do the following to install the arm of the wiper: a. Place the supplied green bushing on the stud located behind the handle of the camera module. The bushing should be in the same orientation as shown in Figure 8. b. Install the wiper arm. Place the ridge of the arm in the notch of the enclosure tab and the slot of the arm over the green bushing. 5. Secure the arm of the wiper and the camera module with the supplied 8-32 Phillips flat head screw (refer to Figure 8).
Install the Pan and Tilt Unit 1. Check for proper seating of the power module seal. Make sure the seal is fully seated in the groove on the top of the power module. POWER MODULE SEAL POWER MODULE Figure 9. Factory-Installed Power Module Seal WARNING: Use caution when attaching the enclosure unit to the power module. If the grooves on the top of the power module are damaged, the integrity of the unit could be compromised. 2. Refer to Figure 10 and attach the pan and tilt unit to the power module.
Install the Sun Shroud 1. Place the supplied nylon washers on the 6-32 Phillips pan head screws. Refer to Figure 11. 2. Align the mounting holes of the sun shroud with the holes on top of the enclosure. 3. Use the supplied nylon washers and screws to secure the sun shroud to the enclosure. NYLON WASHER 6-32 PHILLIPS PAN HEAD SCREW SUN SHROUD Figure 11.
Maintenance CAMERA MODULE REPLACEMENT DANGER: To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the power supply before opening. Keep assembly tightly closed when operating. To replace the camera module do the following: 1. Remove the back cap of the camera enclosure. Refer to Figure 12 and do the following: a. Loosen the set screw with a 1.5 mm Allen wrench. b. Use the supplied spanner wrench to loosen the back cap of the camera enclosure.
3. For models with wipers, also remove the wiper arm and the green bushing from the unit (see Figure 13). 4. Slide the camera module out of the enclosure. WARNING: Never force the camera module into the enclosure. 5. Install the new camera module by doing the following: Slide the camera module into the enclosure. Refer to Figure 14 to position the camera module properly in the enclosure. Carefully mate the camera’s power connector to the mating connector located inside the enclosure.
6. Refer to Figure 13 and do the following to reinstall the arm of the wiper: a. Reinstall the green bushing on the stud located behind the handle of the camera module. b. Reinstall the wiper arm. Place the ridge of the arm in the notch of the enclosure tab and the slot of the arm over the green bushing. 7. Secure the camera module and the wiper arm with the 8-32 Phillips flat head screw (refer to Figure 13). WARNINGS: • To avoid thread damage, carefully install the back cap to the enclosure.
Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VAC Input Voltage Range ±10% Power Consumption Maximum 60 W (120 VA) per system Electrical Connections 6-foot wire harness with connections for power, video, data control, alarm inputs, and auxiliary outputs MECHANICAL Cable Entry One 0.75-inch (1.91 cm) NPT threaded opening Pan Movement 360° continuous pan rotation Vertical Tilt Unobstructed +90° to -90° Variable Pan/Tilt Speed Pan Tilt 0.1° to 40°/sec variable-speed operation 0.
CAMERA/OPTICS Camera Signal Format Scanning System Image Sensor Effective pixels NTSC PAL Horizontal Resolution NTSC PAL Lens Zoom Zoom Speed Horizontal Angle of view Focus Maximum Sensitivity at 35 IRE NTSC PAL Sync System White Balance Shutter Speed NTSC PAL Iris Control Gain Control Video Output Video Signal to Noise Day/Night (23X) Color NTSC, PAL 2:1 Interlace 1/4-inch progressive scan CCD LowLight™ (22X) Color NTSC, PAL 2:1 Interlace 1/4-inch EXview HAD™ CCD 768 (H) x 494 (V) 752 (H) x 582 (V) 7
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
www.pelco.com Pelco, Inc.
