® CCC4000 Series CCD Color Camera Installation/ Operation Manual C1925M (3/99) Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3 DESCRIPTION ................................................................................................................... 3 MODELS .................................................................................................................... 3 LOCATION OF PARTS AND CONTROLS ......................................................................... 4 INSTALLATION ...........
IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installation personnel. 2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials. 3. Use only installation methods and materials capable of supporting four times the maximum specified load.
LOCATION OF PARTS AND CONTROLS FRONT VIEW BACK-FOCUS LOCKING RING CS-MOUNT RING 1/3-INCH CCD ELEMENT REAR VIEW POWER CONNECTOR IRIS CONNECTOR CAMERA MOUNT (1/4-20 UNC) VIDEO OUTPUT (BNC) IRIS CONNECTOR PINOUTS V-PHASE ADJUSTMENT POWER CONNECTOR PINOUTS AC DC– 4 2 3 1 AC DC+ GND PIN 1 = CONTROL COIL + (DAMPING COIL –) PIN 2 = CONTROL COIL – (DAMPING COIL +) PIN 3 = DRIVE COIL + PIN 4 = DRIVE COIL – Figure 1.
INSTALLATION CAMERA MOUNTING Mount the camera using a 1/4–20 mounting screw that does not exceed .197" (4.5 mm ±.2 mm) in length (refer to Figure 2). An optional CA1750 Mount Adapter is supplied to attach the camera to a ceiling mount. CAUTION: Be careful not to damage the camera by screwing the adapter too far onto the threaded stud. As soon as the stud threads appear through the adapter captive nut, tighten the knurled nut. To install the adapter (refer to Figure 3): 1.
POWER REQUIREMENTS An external power supply (not provided) is required when using CCC4000 Series cameras. This camera will accept either AC or DC power in accordance with the chart immediately below. A safety ground terminal ( ) is provided on the connector block to connect the camera to ground potential. Maximum voltage between the supply inputs and the safety ground must be less than 50 volts.
LENS INSTALLATION GENERAL LENS INFORMATION CCC4000 Series cameras are factory adjusted to the CS-mount standard. Fixed iris, manual iris, or passive (DC controlled) auto-iris lenses may be used. Passive (DC controlled) auto-iris lenses require a standard 4-pin square connector (type D4-152N, not supplied) that is standard on all Pelco lenses. C-mount lenses are also compatible by using a Pelco PCMA40 C/CS-mount adapter. Refer to Figure 4.
LENS MOUNTING Do not release the back-focus locking ring unnecessarily. Back-focus adjustment has been set at the factory to the standard CS-mount back-focus distance. To mount a lens: 1. Remove the black protection cover from the CS-mounting ring. 2. If using a C-mount lens, mount a C/CS-mount adapter between lens and camera. Refer to Figure 4. 3. Screw the lens on the camera. Be careful to prevent dust from entering the space between the lens and the CCD element.
b. Adjust the lens and the CS-mount ring together until picture is sharpest. c. Hold the lens and CS-mount ring in place and turn the back-focus locking ring clockwise to tighten. Motorized Zoom Lenses 1. With the camera operating, position the camera to view an object at a distance not less than 45 feet (15 meters) away. 2. Using the camera controller, set the lens in the following manner: 3. a. Zoom out as far as possible (zoom wide). b. Focus on the distant object (focus far). c.
2. Select a second camera that is out of synchronization with the first camera. 3. To shift the V-phase, use a sharp pencil, a toothpick, or some other pointed device capable of being inserted into the V-phase adjustment opening. Each press of the Vphase button will shift the AC linelock by 60 degrees. 4. Switch the cameras back and forth, observing the “roll” between the cameras when they are switched. 5.
SPECIFICATIONS CCD Sensor: Color 1/3-inch interline transfer Pixels NTSC: PAL: 512 H x 492 V 512 H x 582 V Sensing Area: 4.7 x 3.5 mm (3/16 x 1/8 in.) Sync System: Free running/line lock (when AC powered) Horizontal Resolution: 400 TV lines Lens Mount: CS mount Light Sensitivity: 3.5 lux (≥ 50 ire/-6 dB) at f/1.
REGULATORY NOTICES NOTE: This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
