Quick Start Guide Cisco WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access Point
Welcome Thank you for choosing the Cisco WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access Point. The Cisco WAP571E is an outdoor dual radio 802.11ac + 802.11n access point. This guide is designed to familiarize you with the general layout of the access point, describe how to deploy the device in your network, and describe how to configure the device. Your access point has more features and functionality than what is described in this guide. For additional information, see the Administration Guide.
2 Cisco WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access Point Features Front Panel The front panel of the device consists of a single system LED. For a full description of the colors of the light and its indications, see Verifying the Hardware Installation. A Kensington lock slot is found under the lights. Back Panel The back panel of the device has a water proof RJ-45 Ethernet port and reset bottom. Facing the side of the device, the right port (labeled "ETH0/PD") is an 802.3at and 802.
3 Mounting the Cisco WAP571E WirelessAC/N Premium Dual Radio Outdoor Access Point You can place your access point at an outdoor location and mount it on a wall or pole. Placement Tips • Ambient Temperature—To prevent the access point from overheating, do not operate it in an area that exceeds an ambient temperature of 122°F (55°C). • Mechanical Loading—The device should be level, stable, and secure to prevent it from sliding or shifting out of position.
WARNING Insecure mounting might damage the device or cause injury. Cisco is not responsible for damages incurred by insecure wall or pole mounting. Pole-mounting: To mount the Cisco WAP 571E device on a pole: STEP 1 Fix Holder_1 and GND wire on WAP571E by 4 M6*10 screws and screw washers. GND wire can provide better ESD protection. STEP 2 Fix Holder_2 and Holder_3 on Pole by 4 M6*130 screws and screw washers. STEP 3 Fix WAP571E and Holder_1 to Holder_2 by 4 M6*10 Screws and screw washers.
Wall-mounting: To mount the Cisco WAP 571E device on a wall: STEP 1 Fix Holder_1 and GND wire on WAP571E by 4 M6*10 screws and screw washers. GND wire can provide better ESD protection. STEP 2 Fix HOLDER_3 on wall by 4 anchors.
STEP 3 Fix Holder_2 and Holder_3 by 4 M6*10 screws and screw washers. STEP 4 Fix WAP571E and Holder_1 to Holder_2 by 4 M6*10 Screws and screw washers.
7 Cisco WAP571E Wireless Access Point
4 Connecting the Cisco WAP571E WirelessAC/N Premium Dual Radio Outdoor Access Point You can perform the initial configuration using either a wired or wireless connection. The default configuration of the WAP 571 has the Wi-Fi radio turned on. To connect the WAP 571E to the wired network: STEP 1 Connect the Ethernet cable to the Ethernet port of a PoE switch. STEP 2 Connect the other end of the network Ethernet cable to the Ethernet port (PoE) of the wireless access point.
5 Verifying the Hardware Installation To verify the hardware installation, complete the following tasks: • Check the cable connections. • Check the state of the indicator lights. Label Power Activity Off Solid (Green) Solid (Blue) Flashing (Blue) Solid (Red) Description The WAP571E is out of power. The Cisco WAP571E is normal; no wireless client connected. The Cisco WAP571E is normal; at least one wireless client connected. The Cisco WAP571E is upgrading the firmware.
Getting Started with the Configuration 6 To configure the wireless access points, you can either use Ethernet or wireless. Please follow these steps to access the Wizard and then the web-based configuration utility from your computer by Ethernet: STEP 1 Ethernet: Connect the wireless access point to the same network (IP subnet) as your computer. The factory default IP address configuration of the access points is DHCP. Make sure your DHCP server is running and can be reached.
STEP 5 Enter the default user name of cisco and password of cisco in the User Name and Password fields. STEP 6 Click Login. The Wireless Access Point Setup Wizard appears. STEP 7 Follow the Setup Wizard instructions to finish the WAP device installation. We strongly recommend that you use the Setup Wizard for the first installation. The Setup Wizard turns on the Wi-Fi radio, which allows you to connect wirelessly. For more advanced configurations, see the Administration Guide.
Suggested Next Steps 7 Smart PoE Smart PoE is designed for detecting the power level from the PSE (Power Sourcing Equipment) side; it does not matter whether 802.3at or 802.3af mode, the WAP571 will operate at the appropriate mode automatically. Smart PoE ensures that the WAP571E remains functional once powered by 802.3af PSE, and intelligently to adjust operations below: • Second Ethernet port disabled • 2.4-GHz 802.11n radio in 2x2:2 spatial-stream mode • 5-GHz 802.
If it fails, you should get a reply similar to the following: Pinging 192.0.2.10 with 32 bytes of data: Request timed out. Possible Cause of Installation Failure No Power • Power up the switch and your computer if they are turned off. • Make sure your PoE switch is powered on and the lights indicate that you have a link. See Verifying the Hardware Installation. • Verify that the devices on your network are not plugged into a switchable outlet.
If the wireless access points do not receive a DHCP response (there is no DHCP server on your network) after 60 seconds, the access points will fallback to the following default static IP address: 192.168.1.245 and a default mask of 255.255.255.0. To reach that IP address, be sure that your computer is on the 192.168.1.xxx network.
Cisco Firmware Downloads www.cisco.com/go/smallbizfirmware Cisco Open Source Requests www.cisco.com/go/ smallbiz_opensource_request Cisco Partner Central (Partner Login Required) www.cisco.com/web/partners/sell/smb Select a link to download firmware for Cisco Products. No login is required. Product Documentation Cisco WAP571E Administration Guide www.cisco.com/go/300_wap_resources Cisco Power Adapters www.cisco.
Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices) This document provides domestic and international regulatory compliance and safety information for the Cisco WAP571/571E Wireless Access Point EMC Class B Devices. Use this document in conjunction with the documentation available online for the Wireless Access Points.
Translated Safety Warnings • Statement 1—Power Disconnection Warning • Statement 248—Unit Mounting Warning • Statement 1004—Installation Instructions • Statement 1005—Circuit Breaker • Statement 1040—Product Disposal • Statement 1044—Port Connections • Statement 1072—Shock Hazard from Interconnections • Statement 1073—No User-Serviceable Parts • Statement 1074—Comply with Local and National Electrical Codes Statement 1071—Warning Definition Warning IMPORTANT SAFETY INSTRUCTIONS This war
Translated Safety Warnings Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.
Translated Safety Warnings ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
Translated Safety Warnings Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Translated Safety Warnings Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices) 78-20515-02 6
Translated Safety Warnings Statement 1—Power Disconnection Warning Warning Waarschuwing Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord. Voordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT te schakelen en de stekker van het netsnoer uit het stopcontact te halen.
Translated Safety Warnings Varoitus Ennen kuin teet mitään sellaiselle järjestelmälle, jossa on kaksiasentokytkin, katkaise siitä virta ja kytke virtajohto irti. Attention Avant de travailler sur un système équipé d'un commutateur marche-arrêt, mettre l'appareil à l'arrêt (OFF) et débrancher le cordon d'alimentation. Warnung Bevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen das Netzkabel aus der Steckdose.
Translated Safety Warnings Statement 248—Unit Mounting Warning Warning Waarschuwing This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Deze eenheid dient aan een wand te worden bevestigd. Lees voordat u met de installatie begint, de instructies voor wandmontage aandachtig door.
Translated Safety Warnings Statement 1004—Installation Instructions Warning Waarschuwing Varoitus Read the installation instructions before connecting the system to the power source. Statement 1004 Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen. Attention Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Translated Safety Warnings Statement 1005—Circuit Breaker Warning Waarschuwing Varoitus This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 15 A, 125 Vac, or 10A, 240 Vac. Statement 1005 Dit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting (overstroom). Controleer of de beschermingsinrichting niet meer dan: 15 A, 125 Vac, or 10A, 240 Vac is.
Translated Safety Warnings Aviso ¡Advertencia! Varning! Este produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga). Assegure-se de que o fusível ou disjuntor não seja superior a: 15 A, 125 Vac, or 10A, 240 Vac. Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 15 A, 125 Vac, or 10A, 240 Vac.
Translated Safety Warnings Avvertenza Advarsel Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali. Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og bestemmelser. Aviso Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais. ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Translated Safety Warnings Statement 1044—Port Connections Warning Waarschuwing For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection. 10/100/1000 Ethernet Statement 1044 Voor aansluitingen buiten het gebouw waar de apparatuur wordt geïnstalleerd, dienen de volgende poorten aangesloten te worden via een goedgekeurde netwerkafsluiteenheid met integrale circuitbescherming.
Translated Safety Warnings Aviso Para ligações fora do edifício onde o equipamento está instalado, é necessário ligar as seguintes portas através de uma unidade de terminal de rede aprovada com protecção de circuito integral. 10/100/1000 Ethernet ¡Advertencia! Para realizar conexiones en el exterior del edificio en el que esté instalado el equipo, deberá conectar los puertos especificados a continuación a una unidad terminal de red aprobada que cuente con protección de circuitos integrales.
Translated Safety Warnings 10/100/1000 Ethernet 10/100/1000 Ethernet 10/100/1000 Ethernet Statement 1072—Shock Hazard from Interconnections Warning Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.
Translated Safety Warnings Attention Les tensions existant sur les alimentations utilisant la technologie PoE (Power over Ethernet) peuvent constituer un risque d'électrocution si les interconnexions sont effectuées en utilisant des terminaux, conducteurs ou contacts métalliques exposés non isolés.
Translated Safety Warnings Varning! Det kan finnas spänningar på PoE-kretsarna (Power over Ethernet) som utgör risk för stötar om sammankopplingarna görs med ej isolerade, exponerade kontakter, ledare och/eller terminaler av metall. Undvik att använda sådana sammankopplingsmetoder, såvida inte de exponerade metalldelarna finns i en plats med begränsad åtkomst. Användare och servicepersonal som tillåts inom platsen med begränsad åtkomst måste vara medvetna om risken.
Translated Safety Warnings Varoitus Ei sisällä käyttäjän huollettavissa olevia osia. Älä avaa. Attention Aucune pièce se trouvant à l'intérieur ne peut être réparée ou remplacée par l'utilisateur. Ne pas ouvrir. Warnung Enthält keine Teile, die vom Benutzer gewartet werden müssen. Bitte nicht öffnen. Avvertenza Advarsel Aviso Non contiene parti riparabili dall'utente. Non aprire. Inneholder ingen deler som kan repareres av brukeren. Må ikke åpnes. Sem peças sujeitas a manutenção pelo utilizador.
Translated Safety Warnings Statement 1074—Comply with Local and National Electrical Codes Warning Waarschuwing Varoitus Installation of the equipment must comply with local and national electrical codes. Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften. Laitteisto tulee asentaa paikallisten ja kansallisten sähkömääräysten mukaisesti. Attention L'équipement doit être installé conformément aux normes électriques nationales et locales.
Translated Safety Warnings Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices) 78-20515-02 21
Product Usage Restrictions Product Usage Restrictions The Cisco CISCOWAP571/571E WAP571 Wireless Access Point Points are intended for indoor only.use only. The Wireless Access are intended for use indoor Declaration of Conformity Statements The Declaration of Conformity statements for this product can be found at the following URL: http://www.ciscofax.
European Directives Français [French]: Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC. Hrvatski: [Croatian] Ova oprema je u sukladnosti s bitnim zahtjevima i drugim relevantnim odredbama Direktive 1999/5/EC. Íslenska [Icelandic]: Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.
EU Battery Disposal and Recycling Türk [Turkish]: Bu cihaz 1999/5/EC Direktifi'nin temel gereklerine ve ilgili di?er hükümlerine uygundur. Svenska [Swedish]: Declaration of Conformity with Regard to the Directives 2006/95/EC and 2004/108/EC This equipment complies with the essential requirements and other provisions of Directives 2006/95/EC and 2004/108/EC. For more information, please refer to the Declaration of Conformity. EU Battery Disposal and Recycling This product may contain a battery.
EMC Class B Notices and Warnings Table 1 (continued) Specification Description EMC 47CFR FCC Part 15B Industry Canada ICES-003 EN 301 489-1, EN 301 489-17 EN 300 386 EN55022 EN55024 EN61000-3-2 EN61000-3-3 CISPR 22 CISPR 24 AS/NZS CISPR22 Radio 47CFR FCC Part 15C Industry Canada RSS-247 RSS-210 EN 300 328 EN 301893 AS/NZS 4268 RF Exposure FCC OET 65, Supplement C RSS-102 EN 50385 For specific details about the years, revisions and relevant amendments please refer to the
EMC Class B Notices and Warnings • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
EMC Class B Notices and Warnings Class B Notice for Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Statement 295—Class B Warning for Korea Warning This is a Class B Device and is registered for EMC requirements for residential use. This device can be used not only in residential areas but in all other areas.
Japanese Electric Appliance and Radio Laws Japanese Electric Appliance and Radio Laws Statement 571/571E—Power Cable and AC Adapter Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a fire.
Radio Guidelines for Operating Cisco WAP571/571E Wireless Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco WAP571/571E Wireless Access Points in Japan. These guidelines are provided in both English and Japanese. Statement 391—Warning for Low-Power Radio Data Communications Systems (-STD) Warning This equipment shares a frequency band with a wide range of equipment: e.g.
Radio Administrative Rules for Cisco Wireless Devices in Taiwan This section provides administrative rules for operating Cisco wireless access products in Taiwan. The rules are provided in both Chinese and English. Wireless Devices with IEEE 802.11a/b/g Radios Chinese Translation English Translation This equipment is limited for indoor use.
Generic Discussion on RF Exposure English Translation Administrative Rules for Low-Power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units, or users should not change its frequencies, increase its power, or change its original features and functions.
Obtaining Documentation and Submitting a Service Request EU This system has been evaluated for RF exposure for Humans in reference to the ICNIRP (International Commission on Non-Ionizing Radiation Protection) limits.
