User's Manual
Table Of Contents
- QSG_571_EN-ok
- Where to Go From Here
- Before You Begin
- Cisco WAP571 Wireless-AC/N Premium Dual Radio Access Point with PoE Setup Features
- Mounting the Cisco WAP571 Wireless-AC/ N Premium Dual Radio Access Point with PoE Setup
- Connecting the Cisco WAP571 Wireless- AC/N Premium Dual Radio Access Point with PoE Setup
- Verifying the Hardware Installation
- Getting Started with the Configuration
- Suggested Next Steps
- Rebooting the Devices or Returning them to their Factory Default Settings
- WAP571_ClassB_RCSI (For FCC only)_20150819-ok
- Translated Safety Warnings
- Statement 1071—Warning Definition
- Statement 1—Power Disconnection Warning
- Statement 248—Unit Mounting Warning
- Statement 1004—Installation Instructions
- Statement 1005—Circuit Breaker
- Statement 1040—Product Disposal
- Statement 1044—Port Connections
- Statement 1072—Shock Hazard from Interconnections
- Statement 1073—No User-Serviceable Parts
- Statement 1074—Comply with Local and National Electrical Codes
- Product Usage Restrictions
- Declaration of Conformity Statements
- European Directives
- EU Battery Disposal and Recycling
- Standards Compliance
- EMC Class B Notices and Warnings
- Japanese Electric Appliance and Radio Laws
- Radio
- Generic Discussion on RF Exposure
- Obtaining Documentation and Submitting a Service Request
- Translated Safety Warnings
17
Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)
78-20515-02
Translated Safety Warnings
Attention
Les tensions existant sur les alimentations utilisant la technologie PoE (Power over Ethernet)
peuvent constituer un risque d'électrocution si les interconnexions sont effectuées en utilisant
des terminaux, conducteurs ou contacts métalliques exposés non isolés. Évitez d'utiliser de telles
méthodes d'interconnexion à moins que les pièces métalliques exposées ne se trouvent dans un
emplacement d'accès restreint et que les utilisateurs et les responsables du service autorisés
dans cet emplacement d'accès restreint ne soient conscients du danger. Une zone d'accès
restreint peut être accédée uniquement à l'aide d'une clé, d'un outil et d'un verrou spécial, ou
d'autres moyens de sécurité.
Warnung
Bei Power-over-Ethernet-(PoE-)Schaltkreisen besteht u.U. Stromschlaggefahr, wenn
Verbindungen unter Verwendung nicht isolierter, freiliegender Metallkontakte, Leiter oder
Anschlussklemmen hergestellt werden. Vermeiden Sie das Herstellen solcher Verbindungen, es
sei denn, die freiliegenden Metallteile befinden sich an Orten mit beschränktem Zugang, und
Personen, die Zugang dazu haben, sind ausdrücklich über diese Gefahr informiert worden. Ein
Ort mit beschränktem Zugang ist nur mit Hilfe eines speziellen Werkzeugs, Schloss und
Schlüssels oder anderen Sicherheitseinrichtungen zugänglich.
Avvertenza
Nei circuiti con alimentazione via Ethernet (PoE) possono verificarsi pericoli di scosse elettriche
se si creano connessioni con contatti metallici, conduttori o terminali scoperti. Evitare di
utilizzare i metodi di connessione sopraelencati a meno che le parti metalliche esposte non si
trovino in una zona riservata e gli utenti e il personale di assistenza, che sono autorizzati ad
accedere nella suddetta zona, siano stati messi al corrente del pericolo. È possibile accedere alla
zona riservata solamente utilizzando gli appositi elementi di sicurezza.
Advarsel
I strømkretser med PoE (Power over Ethernet) kan det være spenninger som kan utgjøre
støtfare hvis det blir foretatt sammenkoblinger med uisolerte, eksponerte kontakter, ledere
eller terminaler av metall. Unngå å bruke slike sammenkoblingsmetoder med mindre de
eksponerte metalldelene er i et område med begrenset tilgang, og brukere og servicepersonell
som har tilgang til det begrensede området, blir gjort oppmerksom på faren. Et område med
begrenset tilgang kan bare åpnes ved hjelp av spesialverktøy, nøkkel eller andre
sikkerhetstiltak.
Aviso
Pode haver voltagens que representam perigo de choque em circuitos PoE (Power over
Ethernet) se as interconexões forem feitas utilizando-se terminais, condutores ou contatos de
metal exposto e sem isolamento. Evite utilizar tais métodos de interconexão a não ser que as
partes de metal expostas estejam em um local de acesso restrito e os usuários e o pessoal de
serviço com acesso autorizado a este local restrito estejam cientes do perigo. Uma área de acesso
restrito só pode ser acessada com o uso de uma ferramenta, fechadura e chave especial ou de
outros meios de segurança.
¡Advertencia!
Puede haber voltajes con riesgo de shock en circuitos de alimentación sobre el cableado
Ethernet (PoE), si para las interconexiones se utilizan contactos, conductores o terminales
metálicos descubiertos. Evite tales métodos de interconexión, a menos que las partes metálicas
descubiertas se encuentren en un lugar de acceso restringido y tanto los usuarios como el
personal de servicios en dicho lugar sean conscientes de la existencia de tal riesgo. Sólo se puede
tener acceso a una zona de acceso restringido mediante el uso de una herramienta especial, un
candado y una llave u otros medios de seguridad.










