User's Manual
Table Of Contents
- Notice à l’attention des installateurs de réseaux câblés
- Mitteilung für CATV-Techniker
- Aviso a los instaladores de sistemas CATV
- IMPORTANT SAFETY INSTRUCTIONS
- Power Source Warning
- Ground the Product
- Protect the Product from Lightning
- Verify the Power Source from the On/Off Power Light
- Eliminate AC Power/Mains Overloads
- Handling Disposable Batteries
- Provide Ventilation and Select a Location
- Operating Environment
- Protect from Exposure to Moisture and Foreign Objects
- Service Warnings
- Check Product Safety
- Protect the Product When Moving It
- Telephone Equipment Notice
- United States FCC Compliance
- Introducing the DOCSIS Wireless Residential Voice Gateway
- Purpose
- Installing the DOCSIS Wireless Residential Voice Gateway
- Installation Preparations
- Install the Wireless Residential Voice Gateway
- Introduction
- Operation of Front Panel Indicators
- Introduction
- Maintaining the Battery
- Introduction
- Troubleshooting the DOCSIS Wireless Residential Voice Gateway
- Frequently Asked Questions
- How Do I Configure TCP/IP Protocol?
- How Do I Renew the IP Address on My PC?
- What if I Don't Subscribe to Cable TV?
- How Do I Arrange for Installation?
- How Does the Wireless Residential Voice Gateway Connect to My Computer?
- After My Wireless Residential Voice Gateway Is Connected, How Do I Access the Internet?
- Can I Watch TV and Surf the Internet at the Same Time?
- Can I Use my Existing Phone Number with the Wireless Residential Voice Gateway?
- How Many Telephones Can I Connect?
- Common Troubleshooting Issues
- I don't understand the front panel status indicators
- The Wireless Residential Voice Gateway does not register an Ethernet connection
- The Wireless Residential Voice Gateway does not register an Ethernet connection after connecting to a hub
- The Wireless Residential Voice Gateway does not register a cable connection
- There is no dial tone when I lift the handset
- Tips for Improved Performance
- Frequently Asked Questions
- Introduction
- Customer Information
- Introduction
- Index
Chapter 1 Introducing the DOCSIS Wireless Residential Voice Gateway
6 OL-30505-01
7 WIRELESS ON/OFF (Optional)—Press this button to activate and turn on the
Wireless feature. This feature allows users to transfer data over the wireless
connection. When the WIRELESS indicator is ON, it indicates that the Wireless
Access Point is operational. BLINKING indicates that data is being transferred
over the wireless connection. OFF indicates that the Wireless feature has been
disabled.
8 WIRELESS SETUP—Press this button to activate the Wireless Setup feature.
This feature allows users to add new Wireless Protected Setup (WPS) compliant
wireless clients to the home network. When the SETUP indicator is OFF (normal
condition), it indicates that the wireless setup is not active. BLINKING indicates
the user has activated wireless setup to add new wireless clients on the wireless
network.
9 TEL1—ON indicates telephony service is enabled. Blinks when line 1 is in use.
OFF indicates that phone service for TEL 1 is not enabled.
10 TEL2—ON indicates telephony service is enabled. Blinks when line 2 is in use.
OFF indicates that phone service for TEL 2 is not enabled.
11 BATTERY (optional model only)—ON indicates that the battery is charged.
Blinking indicates that the battery charge is low. Off indicates that the unit is
operating from battery power, that the battery charge is depleted, or the battery
is defective or missing.
Notes:
After the residential gateway is successfully registered on the network, the
POWER, DS, US, and ONLINE LEDs illuminate continuously to indicate that the
residential gateway is active and fully operational.
The high-speed data operation is disabled when operating on battery power;
only the telephone service (if available on this model) is active when operating
on battery power.
LEDs may behave differently when the residential gateway is running on battery
power (without AC power). Most LEDs are disabled if the unit is operating on
battery power. In this mode, the POWER LED blinks to indicate that the unit is
operating under battery power.
The residential gateway should only run on battery power when AC power has
failed. If the POWER LED indicates that the unit is running on battery power,
but the AC power has not failed, verify that the power cord is plugged into a
working AC outlet.