Print Vendor Remove Before Printing Printing Specifications Cable Modem and Residential Gateway Quick Start Product Bulletin – NAM/LATAM 78-4043672-01D0 INLET Page Size: Color process: Paper weight: Paper type: Varnish: Number of Pages: A4 Black (1/1) double sided 20# Opaque N/A 1 page (N/A--signatures) COVER N/A BINDING Fold to A7 size, bar code must be visible for scanning. See fold diagram on next page.
Print Vendor Remove Before Printing NOTE: Content of document in this example, except for bar code placement, may not match document to be printed.
This illustration is shown as an example to help you locate the MAC address and serial number for your device. If asked, provide the technician or service provider with the serial number and MAC address as listed on the label of your device. Product Family (Families are Cable Modem, EMTA, Gateway, and Voice Gateway) 5 POWER: Connect the barrel end ( ) of the power adapter (included) to the POWER input on the back of the device. Then, plug the adapter into a wall outlet.
Esta ilustración se muestra a modo de ejemplo para ayudarle a localizar la dirección MAC y el número de serie de su dispositivo. En caso de que el técnico o proveedor de servicios le pida el número de serie y la dirección MAC, proporciónele estos datos tal como aparecen en la etiqueta del dispositivo.
Safety instructions • Read these instructions. • Keep these instructions. • Heed all warnings and cautions. • Follow all instructions. Climatic conditions This product: • Is intended for in-house stationary use; the maximum ambient temperature must not exceed 40 °C (104 °F); the relative humidity must be between 20 and 80 %. • Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation.
Handling batteries This product may contain disposable batteries. CAUTION There is danger of explosion if the battery is mishandled or incorrectly replaced. Replace only with the same or equivalent type of battery. Do not disassemble it or attempt to recharge it outside the system. Do not disassemble, crush, puncture, short the external contacts, dispose of in fire, or expose to fire, water or other liquids. • Insert batteries correctly.
In case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it may only use channels 1 to 11 (2412 to 2462 MHz) on Canada territory. In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it is for indoor use only. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination.
an ou d N Fo ts O r A id T PP e fo R T rd O ec i V hn str AL ic ib ol ut or io !!! n • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
SAFETY INSTRUCTIONS AND REGULATORY NOTICES BEFORE YOU START INSTALLATION OR USE OF THIS PRODUCT, CAREFULLY READ ALL SAFETY INSTRUCTIONS Applicability These Safety Instructions and Regulatory Notices apply to: • Technicolor Cable Modems & Gateways Using equipment safely When using this product, always follow the basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the following: • Always install the product as described in the documentation that is included w
Safety instructions • Read these instructions. • Keep these instructions. • Heed all warnings and cautions. • Follow all instructions. Climatic conditions This product: • Is intended for in-house stationary use; the maximum ambient temperature must not exceed 40 °C (104 °F); the relative humidity must be between 20 and 80 %. • Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation.
Water and moisture Do not use this product near water, for example near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. Transition of the product from a cold environment to a warm one may cause condensation on some of its internal parts. Allow it to dry by itself before using the product. Electrical powering The powering of the product must adhere to the power specifications indicated on the marking labels.
• If liquid has been spilled into the product. • If the product has been exposed to rain or water. • If the product does not operate normally. • If the product has been dropped or damaged in any way. • There are noticeable signs of overheating. • If the product exhibits a distinct change in performance. • If the product is giving off smoke or a burning smell. Protect the product when moving it Always disconnect the power source when moving the product or connecting or disconnecting cables.
• Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
