Installation Guide

Preparation/Assembly
• Adjustable wrench
• Groove joint plier
• Flat screwdriver
• Phillips screwdriver
• Pipe tape
• Hex Wrench
• Hacksaw
Steps 1-3
Installation
Temperature Limiting Device
3
1A
Position face of plaster guard flush with face of finish
wall.
5
For tub installation only: install nipple for spout. Nipple
should extend approximately beyond finished wall.
1. Shut off water supply by turning
check valves. Extract right handle
(the escutcheon with Hot/Cold
mark) and retainer nut. Then, you
will see the limiting device on the
extension.
2. Adjust limiting device to select opti-
mum temperature and to avoid acci-
dental scalding.
1 2
3
H125 x W120mm
2
Apply pipe tape onto thread and connect water supply
tube to valve assemblies. Make sure that the valves’ hot
and cold inlets are on an accurate horizontal plane.
Installation
Parts diagram
4
6
Install shower arm.
8
Install tub spout. Tu rn on water and check for leaks.
9
Install shower flange.
Installation
Steps 7-10
10
Install escutcheon and diverter handle onto valve.
11
Screw in escutcheon and install handle set.
Installation
Steps 11-14
12-3
Keep the distance (B-1/16”) and cut off the extra
cartridge.
13
Adjust the cartridge to be fixed clockwise. Assemble the
handle vertically.
14
Install showerhead and tighten with wrench. Tu rn on
water supply.
12-1
Measure the distance between handle and canopy.
(distance B) (For fiberglass wall
skip step 12)
12-2
Leave 1/16” between canopy & handle head.
Apply pipe tape on all pipe threads. Install elbow at one
end. Connect other end to shower diverter.
Determine whether you’re mounting into
a. Drywall or drywall with tile (See figure A & step 1A)
b. Fiberglass Wall (See figure B & step 1B)
1B
Position plaster guard flush with back of fiberglass wall.
Steps 4-6
7
Before installing escutcheon, remove the plastic cap
from plaster guard by twisting cap to the clockwise.
1A
1B
2
3
4
5
6
7
8
10
9
11
12-1
12-2
12-3
13
14
a. Remove the two white plastic toothed cams from the
valve stem.
b. Tu rn the valve stem so that the round dimple on the
stem is at the top. Thisis the closed position is at the top.
(Thisisthe valve closed position with normal plumbing
hook-up).
"F": DIMPLE
up!!
Install cam (A) onto valve stem
a. Dimple (D) on valve stem and notch (C) on cam A should
both point upward. The flat side of cam A should go
against the stop (B)
b. Rotate valve stem so that cam A is tight to the Stop (B).
A BASE CAM
B TEMPLIMIT CAM
C FIXED STOP
D VA LV E STEM
E ROUND DIMPLE MARK ON STEM
F SLOT IN TEMPLIMIT CAM B
D
G
A
C
CAM A
CAM A
4
Tr ouble-Shooting
PROBLEM
Leaks underneath handle.
CAUSE
Retainer nut has come loose or O-ring on cartridge is dirty or
twisted.
ACTION
Tighten the retainer nut. Clean or replace o-ring.
PROBLEM
Water will not shut off completely.
CAUSE
Rubber valve seat is dirty or broken.
ACTION
Remove handle and cartridge to check the rubber valve seat.
Clean or replace it.
PROBLEM
Water temperature can not be adjusted
by limiting device, or no hot or cold water.
CAUSE
Dirty balance spool.
ACTION
Tu rn off water supply. Unscrew the balance spool and remove
piston and clean with a brush and vinegar water for both
parts.
Per centage of hot water
Recommended
Temperatur e limiting device opened at eight notches is recommended
high temperature
setting
Average tempera-
ture setting
Low temperature
setting
Install temp limit cam (B)
a. The word "up" should face out
b. Installcam onto valve stem so that it fits onto cam A so
that there are no tooth gaps between A & B. Thisallows
valve to rotate from closed to full hot position.
c. See instructions below to adjust temperature limit stop.
CAM B
a. With water on to valve, rotate valve stem counter-clock-
wise to desired high temperature. Letwater run for at least
one minute to confirm temperature.
b. Set cam "B" so that the flat side is flush with the stop (C).
c. Shut off water and re-installhandle assembly.
Indented mark
inbetween "C"
and "H" on
#04901.
Sharp end of
#04900..
E
F
A
C
B
5
6
7
installation
Tools:
Safety Tips
Things You May Need
Important points
Maintenance
What you need to know
Need help?
For additional assistance or service call:
1 888 328-2383 USA 1 800 487-8372 CAN
8 a.m. to 8 p.m. EST Monday-Friday
9 a.m. to 5 p.m. EST Saturday & Sunday
Your new bathroom faucet is designed for
years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft
cloth. Avoid abrasive cleaners, steel wool and harsh chemicals
as these will dull the finish and void your warranty.
Prior to beginning installation, turn off the cold and hot water
lines and open the old faucet to release build-up pressure.
When installing your new faucet, turn the connector nuts finger-
tight, then use one wrench to anchor the fitting and a second
wrench to tighten the nut one additional turn. Connections that
are too tight will reduce the integrity of the system.
Wrap all threaded connections with pipe tape available at
your local hardware or plumbing supply store. Always wrap in
a clockwise direction.
a
• If soldering during faucet installation, the seats cartridges
and washers will have to be removed before using flame.
Otherwise, warranty will be void on these parts.
• Protect your eyes with safety glasses when cutting or
soldering water supply line.
• Cover your drain to avoid loosing parts.
All installations can vary depending on how your previous faucet was installed. Not all supplies for faucet
installation are included; however they are available wherever plumbing supplies are sold. When
choosing your installation supplies, make sure they are IAPMO and/or CSA approved products.
For models: 459849,459885
1/16"
For tub installation only: repeat step 2 for tub spout.
CAUTION: In order to assure proper function, piping
from the bottom port of valve to tub spout outlet MUST
be either 1/2” nominal copper pipe or 1/2” iron pipe.
CAUTION: In order to assure proper function, piping
from the bottom port of valve to tub spout outlet MUST
be either 1/2” nominal copper pipe or 1/2” iron pipe.
F1325700YP F1228100YP_HDK5
10.
9.
7.
8.
6.
5.
4.
19.
20.
11.
12.
13.
14.
15.
16.
17.
18.
21.
1.
2.
3.
1 Shower Head S11B0204
2 Shower Arm A020002
3 Shower Arm Flange A019298
4 Handle Cap A66D803
5 Metal Handle Assembly A66E591H
6 Screw Set(3/16" -24 * 2-15/16" L) A668209
7 Screw Set(3/16" -24 * 1-5/8" L) A608232
8 Plaster Guard A127006
9 Base Nut A009281
10 Retainer Nut A103034
11 Sleeve A217031
12 Temperature Limiting Device A603570
13 Cartridge Assembly A603567
14 Seat & Spring Set A603177
15 Check Valve A603120
16 Pressure Balance Spool A507041
17 Diverter Assembly A607223
18 Escutcheon Assembly A66F114
19 Spout Escutcheon A303071
20 Spout A523265
21 Hex Wrench (H3.18 *20 mm L * 90 mm L) A031017NI