GC-X360S-W GC-X360S-B Game Console Security Cover for Xbox 360S 1 date:01/22/13 #:125-9401
WARNING ENG - This product was designed to be installed on wood stud, solid concrete or cinder block walls. Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is intended for indoor use only.
Tools Needed for Assembly.
Parts List Part Description Quantity Part Number (-B) Part Number (-W) A cover plate 1 125-P1455 125-2455 B 1/4-20 x 1.75" carriage bolt 4 520-1017 520-1017 C #14 2 2.5" hex head wood screw 2 500-1005 500-1005 D 1/4-20 x 1.
1 Wood stud wall. Concrete/Cinder block. 1a 1b Drywall.
1a WARNING When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that the woods studs are a minimum of 2”X4” nominal size. When installing to more than one stud, insure the spacing between studs is at least 16” but does not exceed 24”. Do not install over gypsum board thicker than 5/8”. 1a-1 Use stud finder to locate and mark stud center lines. 1a-2 Level cover plate. Mark mounting holes on stud center lines.
1a-3 Drill mounting holes into supporting surface (2.5" (64 mm) minimum depth required). 2.5" (64mm) 5/32" (4mm) 5/32" (4mm) Mounting hole must center on stud. 1a-4 Level cover plate. Install using wood screws provided. 3/8" (10mm) Maximum 80 in. • lb (9 N.M.).
1b WARNING ENG • When installing Peerless wall mounts on a concrete wall, the wall must be at least 8” thick with a minimum compressive strength of 2000 psi. • When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90 specifications and have a minimum nominal width of 8”. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1” (25 mm) minimum from the side of the block.
1b-3 E Insert anchor flush to concrete. E 1b-4 Level wallplate. Install using concrete anchors and wood screws provided. 3/8" (10mm) Maximum 80 in. • lb (9 N.M.).
WARNING • Drywall must be 1/2" or thicker. • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. 1c-1 Level cover plate and mark the center of the four mounting holes. Drill four 1/2" holes through drywall. NOTE: It may be necessary to drill 5/32" pilot holes prior to drilling 1/2" holes. 2.5" (64mm) 1/2" (12mm) 1c-2 fig. 1.3 1 drill 1/2" hole I Pivot end of toggler (I). 2 I Push into hole.
1d-1 B Level cover plate and mark the center of four rectangular mounting holes Drill four 5/16” (8 mm) dia. holes through desktop ounting surface 5/16" (8 mm) F J BOTTOM OF DESK NOTE: Avoid jamming both slope nuts (F) together, doing so may make it difficult to remove slope nut used for tightening. After slope nut is secure remove bottom slope nut.
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product's manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
