User guide

ManualsBrandsPeerless ManualsOffice FurnitureDS-C560-2X2

2014-04-14 #:009-9082-3.1 (2014-08-19)

ENG

DS-C560-2X2

46"-60"

(117cm-152cm)

500 lb

(227 kg)

MAX

Summary of content (20 pages)

PAGE 1
DS-C560-2X2 46"-60" (117cm-152cm) MAX 500 lb (227 kg) ENG 1 2014-04-14 #:009-9082-3.
PAGE 2
This page intentionally left blank. 2 2014-04-14 #:009-9082-3.
PAGE 3
WARNING Do not begin to install product until you have read and understood the instructions and warnings contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product must be installed onto flat, hard, level surface to prevent tipping. The cart or stand is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. Displays must be removed before moving cart.
PAGE 4
Parts (Before beginning, make sure you have all parts shown below).
PAGE 5
K (1 ) M (2 ) L (1 ) computer shelf computer cover dual rail assembly N (4 ) locking tab O (4 ) cord bracket P (96) M8 x 16mm Q (56) M8 square nut R (24) cover clip S (10) M5 x 10mm U (1 ) V (1 ) 1/4" power bit 5mm allen wrench W (16) nylon shoulder washer T (4 ) M5 x 12mm X (16) M6 x 12mm Y (1 ) 4mm allen wrench 5 2014-04-14 #:009-9082-3.
PAGE 6
1 B Repeat for each caster assembly. Y A (5mm) P (4) Do not fully tighten hardware Q (2) P (2) SIDE VIEW 6 2014-04-14 #:009-9082-3.
PAGE 7
2 Repeat for each base leg assembly. Y Q (2) (5mm) Q (2) D F P (4) Q (2) Q (2) F P (4) 7 2014-04-14 #:009-9082-3.
PAGE 8
3 Repeat for each base leg assembly. TIGHTEN CONNECTING HARDWARE 4 Repeat for each base support (x6). Q (4) P (4) G SIDE VIEW 8 2014-04-14 #:009-9082-3.
PAGE 9
5 TIGHTEN CONNECTING HARDWARE Repeat for each side (x2). H 6 TIGHTEN CONNECTING HARDWARE E 9 2014-04-14 #:009-9082-3.
PAGE 10
7 Repeat for each vertical support bracket (x4). 1/8" (3mm) 1/8" (3mm) Q (4) P (4) J P (2) J (2) DIS J (2) PL 10 AY H EIG HT 2014-04-14 #:009-9082-3.
PAGE 11
8 M TIGHTEN HARDWARE (X2) TIGHTEN HARDWARE (X2) Cross supports must center on vertical leg supports. 11 2014-04-14 #:009-9082-3.
PAGE 12
9 TIGHTEN CONNECTING HARDWARE (X4) 12 2014-04-14 #:009-9082-3.
PAGE 13
14 N O T TIGHTEN CONNECTING HARDWARE N O OPTIONAL: Unlock wheels to move cart to desired location; Lock wheels before hanging screens. T TOP VIEW LOCK WHEELS 13 2014-04-14 #:009-9082-3.
PAGE 14
10 Center adapter brackets vertically on back of screen. X .98" (25mm) 7.87" (200mm) 3.94" (100mm) 2.50" (63mm) 15.75" (400mm) X 2.50" (63mm) 0.91" (23mm) W X P OR 14 x3 2014-04-14 #:009-9082-3.
PAGE 15
11 Hook on displays and secure pin in "locked" position. 15 2014-04-14 #:009-9082-3.
PAGE 16
Display Adjustment IN OUT SIDE SIDE TILT BACKWARD SIDE TILT RIGHT TILT LEFT TOP SIDE UP TILT FORWARD TOP DOWN ROTATE LEFT 16 ROTATE RIGHT 2014-04-14 #:009-9082-3.
PAGE 17
12 L 13 1/8" (3mm) L K S (2) TIGHTEN CONNECTING HARDWARE L 17 2014-04-14 #:009-9082-3.
PAGE 18
15 Repeat for each cover. R (4) C 18 2014-04-14 #:009-9082-3.
PAGE 19
16 Route cables through cord brackets. O O 19 2014-04-14 #:009-9082-3.
PAGE 20
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product's manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.