User Manual

CATALOG NUMBER
SPECIFICATIONS
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com
SPECIFICATIONS
Type: ________________________
Project: ______________________
1
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Classic Round” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
9” Diameter T8
LD9 Classic Round
Construction
One- or two-piece nominal 9” diameter
housing is extruded aluminum. Die-cast aluminum
end plates are mechanically attached with no
exposed fasteners.
Reflectors
Formed steel with white finish.
Shielding
Bae: One piece white painted aluminum bae
with snap-on feature.
Upper Lens: Linear prismatic virgin acrylic with snap
on feature. Lens has interior longitudinal prisms and
smooth exterior.
Lower Lens: Linear prismatic virgin acrylic with snap
on feature. Lens has exterior longitudinal prisms and
smooth interior.
Finish
C041 White white (low gloss) standard; custom
colors available, consult factory.
Electrical
Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.
Luminaire Length
4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’ and 12’. Using internal
joiners 4’, 8’, and 12’ sections can be joined to form
longer rows.
Examples: LD9 030203 T8 12FT R4 120 GEB10PS 1SE EC SCT LP830 F1/24 C100 DL
Suspended / Wall LD9
Classic Round
9” Diameter T8
__________ __________ __________ _________ __________ __________ __________ __________
Luminaire
LD9
LD9W
Light Direction/# of Lamps
Up/# of Lamps Down/Shielding
020202
030203
102102
102201
103103
103202
Lamp Type
32 32W T8
(T5, T5HO available with some
shielding options. Consult
factory for more information.)
Luminaire Row
Length, Special
X FT
Maximum
Section Length
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)
Voltage
120
277
347
Ballast Type
GEB10PS <10% THD Electronic
ADEZ Advance Mark 10 dim
DMHL3D Lutron Hi-Lume dim
ADZT Advance Mark 7 0-10V dim
Reference Ballast Wizard on website
or consult factory for other options.
# of Emergency
Modules
(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections
______________ ________________ ________________ ______________ ______________ ______________ _________________________________
Emergency Type
1
(Blank) None
EC Emergency
circuit
EL Emergency
battery pack
EN Emergency
battery pack
w/night light
circuit
Switching
SCT Single circuit
DCT Dual circuit
Lamp Color
L/LP No lamp
L/LPE No lamp. Wired
for energy saving
lamps.
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI
Reference Lamp Chart on
website or consult factory
for other options.
Mounting Type /
F1/ T-bar ceiling (universal
mounting bracket)
F1A/ T-bar ceiling (UMB with
integrated J-box)
F2/ Hard ceiling (horizontal
J-box)
F3/ Rigid stem
Overall Suspension
24 24”
48 48”
96 96”
144 144”
XX XX”
Overall suspension is
measured from ceiling to
bottom of luminaire.
Finish
C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish
Options
CP Chicago plenum (available
with F1A only)
DL Damp location label
ELH Emergency through wiring w/
separate feed
ELS Emergency through wiring w/
single feed, shared neutral
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NYC New York City code
RIF Radio interference filter
Notes:
1 EL and EC are installed in last 4’ of luminaire sections and are not available concurrently.
Separate feed required for each EL, EC or EN unless ELH or ELS is specified
222201
222750
223202
Solid/Bae Lens/Lens Lens/Solid