User Guide XTREME™ HIGH BRIGHT OUTDOOR DISPLAY MODEL:XHB432, XHB492, XHB552 ENG 1 2018-05-30 #:180-9116-1
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS Electrical Code Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of the National Electric Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the facility. Outlet shall be installed near the equipment and shall be easily accessible.
FCC CAUTION To assure continued compliance and possible undesirable interference, ferrite cores may be used when connecting this display to video equipment; maintain at least 400mm (15.75 inches) spacing to other peripheral devices. FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
GENERAL SAFETY PRECAUTIONS Read before operating equipment Thank you for purchasing our product. Before using it, please read this user guide carefully and follow the instructions for safe operation. Please keep this manual for future reference and always include it when transferring or transporting this product to a different location.
• • • • • • • • WARNING Never apply pressure to the exterior of the LCD screen. If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care. Do NOT climb on the product. Do NOT install within five feet from a body of water. Do NOT use if ambient air temperature exceeds the operating limits. The product is to be secured to building before operation. Product must be carried and supported by at least two persons.
CONTENTS System Installation And Electrical Requirements ...................................................................................2 Electrical Code................................................................................................................................2 Power Source .................................................................................................................................2 FCC Caution......................................................................
SET UP INSTRUCTIONS Parts List Qty 1 1 1 1 1 4 1 1 1 1 XHB432 Part # 180-W1663 410-0049 600-0711 410-0163 560-9646 560-D1734 180-9116 180-9020 983-0721 983-0738 A (1 ) XHB492 Part # 180-W1664 410-0049 600-0711 410-0163 560-9646 560-D1734 180-9116 180-9020 983-0721 983-0738 XHB552 Part # 180-W1665 410-0049 600-0711 410-0163 560-9646 560-D1734 180-9116 180-9020 983-0721 983-0738 B (1 ) display remote POWER TV SOURCE MUTE DVD CBL VCR SAT AUX 1 2 3 4 5 7 8 9 .
Removing Cord Cover 1. 2. Remove (2) M6 low-profile hex screws and rear cover plate using 4mm allen wrench (E). Do not disconnect lanyard. Remove (6) M5 hex screws and cord cover using 4mm allen wrench (E).
Installing Power Cord Insert female end of power cord (D) into power port located inside the input compartment. D Installing Ambient Light Sensor (ALS) Extender (Optional) Installing IR Extender (Optional) Insert the 3.5mm end of the included 5V IR extender into the IR Extender port on the input panel of the display. IR extender port may not be compatible with other 3rd party extenders. Insert the 3.
Connecting Cords Connect source devices to appropriate display input. Make all connections prior to powering on the display. The USB 2.0 Data port is for service and media only. For 5VDC power, use the 5VDC power port. 18 4 ALS IR Extender Extender 17 14 LAN Antenna or Cable 15 16 Mini AV Mini AV Component 1 ___ 12V --- 2500mA RS232C 3 Audio Out USB 2.0 Data Display Port HDMI 1 HDMI 2 HDMI 3 VGA Audio In S/PDIF Optical 5 6 7 8 9 10 11 12 13 USB ___ Power 5V --- 2400mA 2 1.
Connecting Cords 11. VGA – Connects an analog source device with the display and allows FHD video signals to be output to the display. VGA does not support audio. When using a VGA connection the audio output from the source device will need to be connected to the 3.5mm Audio In port on the display. 12. 3.5mm Analog Audio In – Accepts the incoming stereo analog audio signal coming from a VGA connected source device. 13.
Replacing Cord Cover 1. 2. 3. 1 Run power and signal cords through notches. To prevent unwanted interference, route the power cord through the left most notch (see image 1 below). Place the cord cover over the cords being careful not to pinch any of the cords. Loosely install (6) M5 hex cap screws then tighten screws on the cord cover using 4mm allen wrench (E) until the gasket on the cover is fully compressed to the cord gasket .
Replacing Handle Hardware Optional: If removing handles, replace with harware provided. F (4 ) Connect To The Power Source Connect power cord to GFCI outlet.
Prepare The Display For Mounting Install cords prior to mounting your display. Input panel may be obstructed once the display is mounted. A mounting solution is sold separately. Contact your Peerless-AV representative for an outdoor rated mounting solution for your particular application. For your safety, only install an outdoor-rated mount that is suitable for the application and supports the weight of the display.
Prepare The Display For Mounting Model A B C D E F XHB432 39.50" (1003mm) 23.28" (591mm) 37.06" (941mm) 20.84" (529mm) 42.51" (1080mm) 0.33" (8mm) XHB492 44.72" (1136mm) 26.22" (666mm) 42.27" (1074mm) 23.78" (604mm) 48.50" (1232mm) 0.33" (8mm) XHB552 50.07" (1272mm) 29.23" (742mm) 47.62" (1210mm) 26.79" (680mm) 54.64" (1388mm) 0.42" (11mm) A C E B D FRONT VIEW 1.51" (38mm) 1.22" (31mm) 1.
Remote Control Battery Installation And Replacement The remote control is powered by two 1.5V AAA batteries installed at the factory. To install or replace batteries: 1. To remove the battery module of the remote control, remove the two screws on the end of the battery module. Slide the battery module out1 of1 2the12 3 remote control. 23 3 4 4 5 45 6 56 6 2. Insert two new “AAA” size batteries into the 7 7 8 78 9 89 9 . . 0 module. battery 0. 0 3.
OPERATING INSTRUCTIONS Power On/Off The Display Power on your display by using the remote control or the power button on the bottom, left-hand side of the display. The display will power on but image may not appear for several seconds as it completes its power up sequence.
Navigating The On Screen Menu Channel Picture Air / Cable Choose between antenna and cable Picture Mode Theater Personal Standard Dynamic Auto Scan Searches for available channels Favorite Color Temp.
Navigating The On Screen Menu Time Sleep Timer off 5 min 10 min 15 min 30 min Time Zone Atlantic Eastern Central Mountain Time Format Setup Menu English Languages Spanish French 60 min 90 min 120 min 180 min 240 min Transparent (Menu Transparency) Pacific Alaska Hawaii Korean Closed Caption 12-hour 24-hour CC Mode Auto Sync On / Off Clock Wake Up 0% 25% 50% 75% 100% Restore Defaults Enter Current Time CC Off / CC On / CC On Mute Factory reset all options Setup Wizard Enter desired time when
Navigating The On Screen Menu Lock System Lock Enter Password to enter System Lock settings Defaut Password: 0000 Change Allows the password to be password changed System Lock On / Off Input Block TV, AV, Component, DP, HDMI 1, HDMI 2, HDMI 3, PC, USB US Canada TV, MPAA Canadian English, Canadian French RRT Setting Reset RRT Unrated On /Off Hotel Mode Enter password to enter hotel mode settings Defaut Password: 0000 Hotel Mode On / Off Change Allows the password to be Password changed Picture Mode St
USB Functionality 1 2 ENG Insert USB flash drive into USB 2.0 Data ENG Select USB source to access content. port on the input panel of the display. Input Source TV AV Component DP HDMI1 USB 2.
USB Functionality 3 ENG Select media type and folder where content is stored. PHOTO PHOTO Return Return 4 POWER TV MUTE DVD CBL VCR MUSIC MUSIC MOVIE MOVIE TEXT TEXT C C Photos – To view a single photo, select photo and press play. To view a slide show, select multiple photos and press play. Use on screen menu to control slide show. Movies – To view a single video, select video and press play. To view a playlist, select multiple videos and press play. Use on screen menu to control playlist.
(RS-232C) Serial Control Of The Display Attach an RS-232C cable (straight through type) to the supplied D-Sub RS-232C for the connections. This operation system should be used by a person who is accustomed to using computers.
MAINTENANCE Care Of The Screen Do not rub or strike the screen with anything hard as this may scratch, mark, or even damage the screen permanently. Ensure that the display is installed in a location where it will be safe from abrasives and flying debris, which could damage the LCD panel. Never use ammonia or any product containing ammonia, as it will damage the anti-glare coating on the face of the display. Only use an approved screen cleaner to clean the display face.
PRODUCT SPECIFICATIONS Specifications subject to change without notice. Display Display Controller Features Screen Size XHB432: 43" (diagonal) XHB492: 49" XHB552: 55" Aspect Ratio Analog Display NTSC Digital Display ATSC / QAM 256 / MPEG4 / H.
Mechanical Display Size: XHB432 XHB492 XHB552 Enclosure Color VESA Mount Net Weight XHB432 XHB492 XHB552 Shipping Size XHB432 XHB492 XHB552 Shipping Weight: XHB432 XHB492 XHB552 Glass Input/Output Connections Display Input Coax (x1), 75 ohm, NTSC, ATSC, H.264, QAM 256 (W x H x D) 39.5" x 23.28" x 4.89" (1003 x 591 x 124mm) 44.72" x 26.22" x 3.92" (1136 x 666 x 100mm) 50.07" x 29.23" x 3.
LIMITED TWO-YEAR WARRANTY TWO-YEAR PARTS & LABOR LIMITED WARRANTY • The LCD is a Class 2 ISO panel. As such, the Pixel Fault for Class II Panels states: Type 1 = Hot Pixel (always on – white); Type 2 = Dead Pixel (always off – black); or Type 3 = A Stuck Pixel (one or more sub-pixels (red, blue or green) are always on or always off.
Peerless-AV 2300 White Oak Circle Aurora, IL 60502 Email: tech@peerlessmounts.com Ph: (800) 865-2112 Fax: (800) 359-6500 www.peerless-av.com Peerless-AV Europe Unit 3 Watford Interchange, Colonial Way, Watford, Herts, WD24 4WP, United Kingdom Customer Care 44 (0) 1923 200 100 www.peerless-av.com Peerless-AV de Mexico Ave de las Industrias 413 Parque Industrial Escobedo Escobedo N.L Mexico 66062 Servicio al Cliente 01-800-849-65-77 www.peerless-av.com © 2018, Peerless Industries, Inc.
