Installation

ManualsBrandsPeerless-AV ManualsHardwareWSP701

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 10-06-09 SHEET #: 095-9301-2 09-25-10

80 lbs. (36 kg) 25 lbs. (11 kg)

SA740P SA730P

SP740P SP730P

PA740 PA730

PP740 PP730

SA746P SA735P

SP746P SP735P

PA746F PA735F

Installing Wall Plate to Wood Stud Walls

for:

PA730, PP730, SA730P, SP730P, PA740, PP740, SA740P,

SP740P, SP735P, SA735P, PA735F, SP746P, SA746P, PA746F

Models: WSP700, WSP701

NOTE: Read entire instruction sheet before you start installation and assembly.

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

Parts List WSP700 WSP701

Description Qty. Part Numbe

Part Numbe

wall plate 1 024-P1050 024-P1051

B wood screw #14 x 2.5 phillips hex head 4 5S1-015-C03 5S1-015-C03

C phillips screw, 1/4 - 20 x .5 blac

2 520-1209 520-1209

Tools Needed for Assembly

• stud ﬁ nder ("edge to edge" stud ﬁ nder is recommended)

• phillips screwdriver

• drill

• 5/32" (4 mm) bit for wood stud wall

• level

WSP700

WSP701

Max UL Load Capacity

WSP700

WSP701

USC

Summary of content (6 pages)

PAGE 1
Installing Wall Plate to Wood Stud Walls for: PA730, PP730, SA730P, SP730P, PA740, PP740, SA740P, Models: WSP700, WSP701 SP740P, SP735P, SA735P, PA735F, SP746P, SA746P, PA746F Max UL Load Capacity 80 lbs. (36 kg) SA740P SP740P PA740 PP740 SA746P SP746P PA746F 25 lbs. (11 kg) SA730P SP730P PA730 PP730 SA735P SP735P PA735F C UL © US WSP701 WSP700 NOTE: Read entire instruction sheet before you start installation and assembly. Before you begin, make sure all parts shown are included with your product.
PAGE 2
1 Wood Stud Installation WARNING Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Draw a vertical line down the center of each stud. Place wall plate (A) on wall as a template. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2 1/2" (64 mm) deep. Attach wall plate (A) using four wood screws (B).
PAGE 3
Instalación de la placa de apoyo en paredes con montantes de madera: PA730, PP730, SA730P, SP730P, PA740, Modelos: WSP700, WSP701 PP740, SA740P, SP740P, SP735P, SA735P, PA735F, SP746P, SA746P, PA746F Máxima UL capacidad de carga 80 lbs. (36 kg) SA740P SP740P PA740 PP740 SA746P SP746P PA746F 25 lbs. (11 kg) SA730P SP730P PA730 PP730 SA735P SP735P PA735F C UL © US WSP701 WSP700 NOTA: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.
PAGE 4
Español 1 Instalación en una pared con montantes de madera dobles Utilice un localizador de montantes para ubicar los bordes de los montantes. Se recomienda usar un localizador de montantes de “borde a borde”. Trace una línea vertical por el centro de cada montante. Coloque la placa de apoyo (A) en la pared para usarla como plantilla. Nivele la placa y marque el centro de los cuatro agujeros. Asegúrese de que los agujeros de montaje se encuentren en la línea central de los montantes.
PAGE 5
Installation d’une plaque murale sur des murs à montants montants en bois: PA730, PP730, SA730P, SP730P, PA740, PP740, Modéles: WSP700, WSP701 SA740P, SP740P, SP735P, SA735P, PA735F, SP746P, SA746P, PA746F Capacité UL de charge maximale préconisée 80 lbs. (36 kg) SA740P SP740P PA740 PP740 SA746P SP746P PA746F 25 lbs. (11 kg) SA730P SP730P PA730 PP730 SA735P SP735P PA735F C UL © US WSP701 WSP700 REMARQUE: lisez entièrement la fiche d’instructions avant de commencer l’installation et l’assemblage.
PAGE 6
Français 1 Installation sur un mur à doubles montants en bois Utilisez un localisateur de montants pour repérer les bords des montants. L’usage d’un localisateur bord à bord est fortement conseillé. Tracez une ligne verticale le long du centre de chaque montant. Utilisez la plaque murale (A) comme gabarit et placez-la sur le mur. Mettez la plaque de niveau et marquez le centre des quatre trous de montage. Assurez-vous que les trous de montage se trouvent sur les axes des montants.