Installation

ManualsBrandsPeerless-AV ManualsHardwareVPM25-W

ISSUED: 05-19-04 SHEET #: 081-9031-2 08-31-04

For customer service call 1-800-729-0307 or 708-865-8870.

Visit the Peerless Web Site at www.peerlessindustries.com

1 of 5

This product is intended for use with UL

Listed products and must be installed by a

qualified professional installer.

Read instruction sheet before you start installation and assembly.

Maximum Load Capacity:

50 lb (22.7 kg)

Models: VPM 25-W,

SVPM 25-W

DVD/DVR/VCR Mount for

Slimline

Standard Wall Mount

Installation and Assembly -

DVD/DVR/VCR MOUNT

SLIMLINE WALL MOUNT

Installing a Single DVD/DVR/VCR Mount .......................................................................................................... page 4

Installing Multiple DVD/DVR/VCR Mounts ......................................................................................................... page 5

WIDTH (W) HEIGHT (H) MAXIMUM MINIMUM

13.25" - 17.25" 1.5" - 2.75" 17.25" x 2.50" 13.25" x 1.5"

(337 mm - 438 mm) (38 mm - 70 mm) (438 mm x 64 mm) (337 mm x 38 mm)

INSIDE DIMENSIONS MEDIA PLAYER DIMENSIONS

Summary of content (5 pages)

PAGE 1
Installation and Assembly - R DVD/DVR/VCR Mount for Slimline® Standard Wall Mount Models: VPM 25-W, SVPM 25-W Maximum Load Capacity: 50 lb (22.7 kg) This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Read instruction sheet before you start installation and assembly. Installing a Single DVD/DVR/VCR Mount ..........................................................................................................
PAGE 2
Parts List A B C D E F G H I VPM 25-W Description Qty. Part DVD/DVR/DVR mount 1 081-0072 hanger bracket 1 1245-271 M5 x .8 x 12 mm phillips screw/washer combo 4 520-1030 #10-24 x 1/2" carriage bolt 4 520-9523 #10-24 nylock nut 4 530-9341 #10 SAE washer 4 540-9400 M5 x 1" penta-pin™ tool driver 1 – 1.5" x 4.5" x .125" adhesive foam 2 599-1122 .375" x 12.75" x .
PAGE 3
Peel and place four pieces of adhesive foam (H, I) on the horizontal cross support and vertical adjusters as shown in figure 1.1 and 1.2. I VERTICAL ADJUSTER HORIZONTAL CROSS SUPPORT H fig 1.2 fig 1.1 Slide hanger bracket (B) onto arm, underneath the tray. Attach DVD/DVR/VCR mount (A) to hanger bracket (B) using four M5 x 12 mm screw/washer combos (C) as shown below. SLIMLINE WALL MOUNT B A C 3 of 5 Visit the Peerless Web Site at www.peerlessindustries.
PAGE 4
Installing a Single DVD/DVR/VCR Mount Adjust size of DVD/DVR/VCR mount (A) to fit media player by loosening vertical and horizontal adjustment screws where shown in figure 2.1 on both sides. Insert media player and align front of player with front of TV on Slimline® wall mount. Tighten vertical and horizontal adjustment screws where shown in figure 2.2 on both sides until player securely fits in mount. Note: TV and Slimline wall mount not shown in illustrations.
PAGE 5
Installing Multiple DVD/DVR/VCR Mounts If adhesive foam (H) is covering slots, trim foam (H) to expose slots. Insert four carriage bolts (D) into slots of upper DVD mount (A). Loosely attach lower DVD mount (A) using four #10 SAE washers (F) and #10-24 nylock nuts (E). This will allow access to the vertical adjustment screws of the upper mount by being able to easily move the lower mount. Note: TV and TV mount not shown in illustrations.