Installation and Assembly: Flat Panel Display Cart Models: SC590, SC590-S ACC964 (sold separately) Max Load Capacity: 300 lb (136.1 kg) 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.
Before you begin, make sure all parts shown are included with your product. Parts List A B C D E F G H I J K L M N Q R S T U V W X Description mount bracket hook plate M10 x .402 ID lock washer base universal plate adapter bracket upright top cover 1/4-20 x 12mm decorative screw 1/4-20mm nut M10 x 15 mm socket screw 3/8-16 x 2.5" socket screw 7/32" allen wrench 6 mm allen wrench 4 mm allen wrench right leg left leg wheel caster wheel caster/brake joint connector nut 3/8-16 x 1.
Parts may appear slightly different than illustrated. Parts List continued I J K M L T R N Q U V W S X Security Tilt Bracket Fasteners M4 x 12mm (6) (510-1079) M4 x 25mm (4) (510-1082) M5 x 12mm (4) (520-1064) M5 x 25mm (4) (520-1122) M6 x 12mm (4) (520-1050) .75" spacer (540-1059) (4) M6 x 20mm (4) (520-9554) M8 x 15mm (6) (520-1068) M6 x 25mm (4) (520-1211) M8 x 25mm (4) (520-1101) M6 x 30mm (4) (520-1067) M8 x 40mm (4) (520-1152) 4 of 12 multi-washer (6) (580-1036) .
1 Insert right leg (R) into base housing (D) as shown in fig. 1.1. Then align holes in right leg with holes in base housing (D). Fasten base housing to right leg using two 3/8-16 x 1.5" bolts (W) and two joint connectors (V). NOTE: Left and right legs can be identified by looking at the cart from the front. Repeat for left side with left leg (S). fig. 1.1 fig. 1.2 S V D R R FRONT OF CART FRONT OF LEG 2 W Insert casters (U & T) into holes of support legs (R & S) and hand thread to secure.
3 Attach uprights (G) to base (D), as shown below using six 3/8-16 x 2.5" socket screws (L) and M10 x .402ID lock washers (C). Tighten all screws. fig. 3.1 G D C L 4 Loosely attach six 1/4-20 x 12 mm screws (I) and 1/4-20 nuts (J) to mount bracket (A). 5 Repeat with second mount bracket (A) Slide mount bracket (A) onto upright (G) so that 1/420 nuts (J) slide into slots of upright (G) as shown in figure 5.1 and detail 1.
6 7 Snap top cover (H) onto upright (G). Insert two 1/4-20 x 12 mm screws (I) into mount bracket (A), leaving 3/16" of exposed thread as shown in figure 7.1 and detail 2. fig. 7.1 H I G 3/16" DETAIL 2 A Attaching Universal Adapter Plate 8 Attach one universal plate (E) to two hook plates (B) using eight M10 x 15 mm socket screws (K). Tighten screws using 6 mm allen wrench (N). 9 Attach hook plate (B) to mount bracket (A).
10 Insert two 1/4-20 x 12 mm screws (I) into holes indicated below for desired display orientation. Tighten all screws using 4 mm allen wrench (Q).
Installing Adapter Brackets WARNING • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to display or product may fail.
For Flat Back Display 11-1 Begin with the shortest length screw, hand thread through multi-washer and adapter bracket (F) into display as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
Mounting and Removing Flat Panel Display WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel display. 12 Hook adapter brackets (F) onto universal plate (E), then slowly swing display in as shown. Turn safety screws, using security allen wrench (Q), clockwise at least six times to prevent display from being removed as shown in detail 3. NOTE: To lock the display down, tighten safety screws to wall plate as shown in cross section.
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
