Installation Owner's manual

ManualsBrandsPeerless-AV ManualsFurniturePM610

1 of 10

Model: PM 610

PM 610S

PM 610W

Installation and Assembly - Electronics Tower

Maximum Load Capacity (Each Shelf):

15.00 lb (7.0 kg)

Installations:

To Wood Stud Walls ........................................................................................................ page 2

To Solid Concrete, Cinder Block, and Brick Walls ........................................................ page 3

IMPORTANT! Turn to the appropriate page for your wall installation.

Read instruction sheet before you start installation and assembly.

WARNING

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware

and components.

PUBLICATION: 12-20-99 SHEET#: 021-9003-3 03-23-05

Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.

Summary of content (10 pages)

PAGE 1
Model: PM 610 PM 610S PM 610W Installation and Assembly - Electronics Tower Maximum Load Capacity (Each Shelf): 15.00 lb (7.0 kg) Read instruction sheet before you start installation and assembly. WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block.
PAGE 2
Before you start make sure all parts listed are included with your product. Parts List A B C D E F G H Description wall bracket shelf bracket equipment support #14 x 2.
PAGE 3
WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
PAGE 4
3 Attach shelf bracket (B) to wall bracket (A) with four screws (E) using allen wrench. E A B 4 Snap eight end caps (G) into four equipment supports (C). Attach four equipment supports (C) to shelf bracket (B). Additional equipment supports can be ordered under model ACC102. B C G G 4 of 10 Visit the Peerless Web Site at www.peerlessindustries.com PUBLICATION: 12-20-99 SHEET#: 021-9003-3 03-23-05 For customer service call 1-800-729-0307 or 708-865-8870.
PAGE 5
Attach eight strips of adhesive foam (F) to tops of equipment supports (C). C F C 5 of 10 Visit the Peerless Web Site at www.peerlessindustries.com © 2004 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners. PUBLICATION: 12-20-99 SHEET#: 021-9003-3 03-23-05 For customer service call 1-800-729-0307 or 708-865-8870.
PAGE 6
Instalación y ensamb laje - Tor a equipos electrónicos ensamblaje orrre par para Modelo: PM 610 PM 610S PM 610W NOTA: Lea toda la hoja de instrucciones antes de iniciar la instalación y el montaje. ADVERTENCIA • El concreto tiene que tener una densidad mínima de 2,000 psi. Es posible que un concreto de menos densidad no sostenga el anclaje para concreto. • Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los fijadores y componentes.
PAGE 7
Antes de comenzar, coteje la lista de piezas para asegurarse de que se han incluido todas las piezas. Parts List A B C D E F G H Descripción soporte de pared soporte para repisas soporte para el equipo #14 x 2.5" tonillo 1/4-20 x 3/8" tonillo espuma para vídeograbadoras cubiertas para extremos 5/32" llave allen Cantidad 1 1 4 5 4 8 8 1 PM 610 N.o de pieza 021-1035 021-1027 021-1031 5S1-015-C03 520-2015 599-3802 590-1077 560-9706 PM 610S N.
PAGE 8
ADVERTENCIA • El concreto tiene que tener una densidad mínima de 2,000 psi. Es posible que un concreto de menos densidad no sostenga el anclaje para concreto. • Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los fijadores y componentes. Instalación en paredes de concreto maciz o, de b loques de hor migón de macizo bloques hormigón escorias y de ladrillo Se necesitan dos juegos de anclajes para concreto alligator® (ACC 203).
PAGE 9
3 Fije el soporte para repisas (B) al soporte de pared (A) con cuatro tornillos (E) usando una llave allen. E A B 4 Coloque ocho cubiertas para extremos (G) en cuatro soportes para el equipo (C). Coloque cuatro soportes para el equipo (C) en el soporte para repisas (B). Puede ordenar más soportes para el equipo bajo el modelo ACC102. B . C G G 9 of 10 Visite el sitio Web de Peerless en www.peerlessmounts.
PAGE 10
5 Pegue ocho tiras de espuma adhesiva (F) a la parte superior de cada soporte para el equipo (C). C F C 10 of 10 Visite el sitio Web de Peerless en www.peerlessmounts.com © 2004 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.