Installation Owner's manual

ManualsBrandsPeerless-AV ManualsHardwarePLP-UNM-S

1 of 5

ISSUED: 06-01-06 SHEET #: 202-9145-4 08-08-12

Installation and Assembly - Universal Adapter

Bracket for 22" - 46" LCD Screens

Models: PLP-UNM, PLP-UNM-S,

PLP-UNMP, PLP-UNMP-S

IMPORTANT! Read instruction sheet before you start installation and assembly.

Used with specific

mounts only

PLP-UNM PLP-UNM-S PLP-UNMP PLP-UNMP-S

Description Qty Part # Part # Part # Part #

adapter plate 1 201-1016 201-4016 201-1016 201-4016

adapter bracket 2 201-1512 201-4512 201-1515 201-4515

allen wrench 1 560-9646 560-9646 560-0072 560-0072

M5 x 10mm screw 4 520-1063 520-1063 520-9250 520-9250

Parts List

Before you begin, make sure all parts shown are included with your product.

Summary of content (5 pages)

PAGE 1
Installation and Assembly - Universal Adapter Bracket for 22" - 46" LCD Screens Models: PLP-UNM, PLP-UNM-S, PLP-UNMP, PLP-UNMP-S IMPORTANT! Read instruction sheet before you start installation and assembly. Before you begin, make sure all parts shown are included with your product.
PAGE 2
Security Adapter Bracket Fasteners M4 x 12 mm (4) 510-1079 M5 x 12 mm (4) 520-1064 M6 x 12 mm (4) 520-1050 M4 x 25 mm (4) 510-1082 I.D. .26" (6.6 mm) (4) 540-1058 M5 x 25 mm (4) 520-1122 M6 x 25 mm (4) 520-1211 I.D. .203" (5.16 mm) (4) 540-1040 Phillips Adapter Bracket Fasteners M4 x 12 mm (4) 504-9013 M5 x 12 mm (4) 520-1027 M6 x 12 mm (4) 520-1128 M4 x 25 mm (4) 504-1015 I.D. .26" (6.6 mm) (4) 540-1058 M5 x 25 mm (4) 520-9543 M6 x 25 mm (4) 520-1208 I.D. .203" (5.
PAGE 3
Installing Adapter Brackets WARNING • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.
PAGE 4
For Flat Back Screen 1-1 Begin with the shortest length screw, hand thread through washer and adapter bracket into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws. NOTE: Spacers may not be used, depending upon the type of screen. fig. 1.
PAGE 5
Mounting and Removing Flat Panel Screen WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. Refer to mount instruction sheet for attachment of adapter plate to mount. 2 Hook adapter brackets (BB) onto adapter plate (AA), then slowly swing screen in as shown. Turn screws clockwise at least six times to prevent screen from being removed as shown in detail 1. NOTE: Tighten screws using allen wrench (CC).