MOD-FW2KIT300 MOD-FW2KIT300-B 46" - 90" (117 - 229 cm) MAX 211 lb (96 kg) ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR 1 2014-02-04 #:203-9371-2 (2014-04-11)
WARNING ENG - Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury.
AVISO POR - Antes da instalação, certifique-se de que a superfície de suporte suporta a carga combinada do equipamento e das ferragens. Os parafusos têm de ser bem apertados. Não aperte em demasia, pois podem ocorrer danos ou falha do equipamento. Nunca exceda a capacidade de carga máxima. Este produto destina-se a utilização apenas em ambientes interiores. A utilização deste produto ao ar livre pode conduzir a falha do produto ou ferimentos pessoais.
ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR Parts (Before beginning, make sure you have all parts shown below). Piezas (antes de iniciar, asegúrese de tener todas las piezas siguientes). Pièces (avant de commencer, assurez-vous d’avoir toutes les pièces illustrées ci-dessous). Teile (Achten Sie vor Beginn der Arbeiten darauf, dass alle unten abgebildeten Teile vorhanden sind). Onderdelen (hoort u zich ervan te overtuigen dat u alle onderdelen hebt, die hieronder te zien zijn).
F (1) G (1) tilt box tilt plate H (2) horizontal rail I (2) vertical rail J (8) K (8) M5 x 10mm L (4) M8 x 15mm M8 x 55mm M (4) P (4) set screw M6 x 80mm Q (4) R (4) M5 x 16mm N (2 ) S (2 ) M6 nut support collar O (1) 4mm allen wrench 5mm allen wrench T (1) U (2) wall plate M5 x 10mm AA (4) BB (4) M6 x 12mm CC (4) M6 x 25mm DD (4) M8 x 12mm EE (8) M8 x 25mm FF (8) spacer M6/M8 washer 5 2014-02-04 #:203-9371-2 (2014-04-11)
ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR Tools Needed for Assembly. Herramientas necesarias para el ensamblaje. Outils nécessaires au montage. Für den Zusammenbau erforderliche Werkzeuge. Voor montage benodigd gereedschap. Attrezzi necessari per l’assemblaggio. Nástroje potřebné k montáži. Nástroje potrebné na montáž. Ferramentas necessárias para a montagem. Montaj İçin Gerekli Aletler. 7/32" (5.5mm) ENG To properly tighten screws: Tighten until screw head makes contact, then tighten another 1/2 turn.
1 ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR Wood stud wall. Pared de madera. Mur en bois. Holzwand. Houten muur. Parete di legno. Dřevěná stěna. Drevená stena. Parede de madeira. Ahşap duvar. 1a-1 Concrete/Cinder block. Concreto/Bloque de hormigón. Béton/bloc de béton. Beton/Porenbetonstein. Beton/B2-blokken. Calcestruzzo solido/forato. Betonový/škvárový blok. Betónový/škvarový blok. Betão/bloco de cimento. Beton/Briket.
1a-2 B 1a-3 T ENG Mark mounting holes on stud center lines. ESP Marque los orificios de montaje en las líneas centrales del montante. FRN Marquez les trous de fixation le long de la ligne médiane du montant. DEU Markieren Sie die Montagelöcher auf den NEL Ständer-Mittellinien. ITL Markeer montagegaten op het midden van de balken. ČEŠ Contrassegna i fori di montaggio sulle linee centrali dei montanti. SLK Na střední linii stěny vyznačte montážní otvory.
1a-4 3" (76mm) 3/16" (5mm) 3/16" (5mm) ENG Drill mounting holes into supporting surface (3" (76mm) minimum depth required). ESP Taladre los agujeros de montaje en la superficie de apoyo; se requiere una profundidad mínima de 3" (76mm). FRN Percez les trous de fixation dans la surface de support, une profondeur minimale de 3 po (76mm) est requise. DEU Bohren Sie Montagelöcher in die Montagefläche; Mindesttiefe von 76mm (3 Zoll) erforderlich.
1b WARNING ENG • When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum compressive strength of 2000 psi. • When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90 specifications and have a minimum nominal width of 8". Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block.
VÝSTRAHA SLK • Pri inštalácii nástenného držiaka Peerless na betónovú stenu musí mať táto stena hrúbku minimálne 20 cm a minimálnu pevnosť v tlaku 2000 psi (13,8 tisíc kPa). • Pri inštalácii nástenného držiaka Peerless na stenu zo škvarových tvárnic musia tieto tvárnice spĺňať špecifikácie ASTM C-90 a musia mať minimálnu nominálnu šírku 20 cm (8 palcov). Nevŕtajte do škár vyplnených maltou! Vždy musíte montovať do pevnej časti tvárnice, všeobecne najmenej 25 mm (1 palec) od okraja tvárnice.
1b-1 B 1b-2 T ENG Mark mounting holes on stud center lines. ESP Marque los orificios de montaje en las líneas centrales del montante. FRN Marquez les trous de fixation le long de la ligne médiane du montant. DEU Markieren Sie die Montagelöcher auf den NEL Ständer-Mittellinien. ITL Markeer montagegaten op het midden van de balken. ČEŠ Contrassegna i fori di montaggio sulle linee centrali dei montanti. SLK Na střední linii stěny vyznačte montážní otvory. POR Na stredné čiary steny vyznačte montážne otvory.
1b-3 3" (76mm) 3/8" (10mm) 3/8" (10mm) ENG Drill mounting holes into supporting surface (3" (76mm) minimum depth required). ESP Taladre los agujeros de montaje en la superficie de apoyo; se requiere una profundidad mínima de 3" (76mm). FRN Percez les trous de fixation dans la surface de support, une profondeur minimale de 3 po (76mm) est requise. DEU Bohren Sie Montagelöcher in die Montagefläche; Mindesttiefe von 76mm (3 Zoll) erforderlich.
1b-5 7/16" (11mm) T ENG Level wallplate. Install using concrete anchors and wood screws provided. ESP Nivele e instale. FRN Mettez à niveau et procédez au montage. DEU Waagerecht ausrichten und anbringen. NEL Installeer de schroeven waterpas. ITL Livella e installa. ČEŠ Vyrovnejte a namontujte. SLK Vyrovnajte a namontujte. POR Nivelar e instalar. TÜR Dengeleyin ve takın.
2-1 2-3 F N (10mm) 4mm wrench R (2) J C 2-2 F C P (2) B (2) 3-1 3-2 O 5mm wrench M (2) A L (2) 15 2014-02-04 #:203-9371-2 (2014-04-11)
4 1 C (10mm) 2 U (2) 3 C 4 P (2) R (2) 16 2014-02-04 #:203-9371-2 (2014-04-11)
5 ENG Level, mark mounting holes then refer to step 6a or 6b to secure mounting plate to floor. ESP Nivele, marque los agujeros de montaje y consulte el paso 6a o 6b para fijar la placa de montaje en el suelo. FRN Mettez-la à niveau, marquez les trous de fixation, puis reportez-vous aux étapes 6a ou 6b pour fixer la plaque de montage au plancher.
6a-1 7/32" (5.5mm) ENG Drill mounting holes into supporting surface (3" (76mm) minimum depth required). ESP Taladre los agujeros de montaje en la superficie de apoyo; se requiere una profundidad mínima de 3" (76mm). FRN Percez les trous de fixation dans la surface de support, une profondeur minimale de 3 po (76mm) est requise. DEU Bohren Sie Montagelöcher in die Montagefläche; Mindesttiefe von 76mm (3 Zoll) erforderlich.
6b-1 3/8" (10mm) ENG Drill mounting holes into supporting surface (3" (76mm) minimum depth required). ESP Taladre los agujeros de montaje en la superficie de apoyo; se requiere una profundidad mínima de 3" (76mm). FRN Percez les trous de fixation dans la surface de support, une profondeur minimale de 3 po (76mm) est requise. DEU Bohren Sie Montagelöcher in die Montagefläche; Mindesttiefe von 76mm (3 Zoll) erforderlich.
6b-3 2b-4 ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR Install using concrete anchors and wood screws provided. Nivele e instale. Mettez à niveau et procédez au montage. Waagerecht ausrichten und anbringen. Installeer de schroeven waterpas. Livella e installa. Vyrovnejte a namontujte. Vyrovnajte a namontujte. Nivelar e instalar. Dengeleyin ve takın. 7/16" (11mm) E (4) A ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR Maximum 80 in-lb (9 Nm). Máxima 80 in-lb (9 Nm). Maximum 80 in-lb (9 Nm). Maximale 80 in-lb (9 Nm).
8 8a 8b-1 8a x3 ENG Screws must get at least three full turns and fit snug. ESP Los tornillos tienen que dar, por lo menos, tres vueltas completas y quedar ajustados. FRN Il faut effectuer au moins trois tours de vis complets et bien serrer les vis. DEU Schrauben sind mindestens drei volle Umdrehungen einzudrehen und müssen fest anliegen. NEL De schroeven moeten ten minste drie hele slagen worden aangedraaid en stevig vastzitten. ITL Girare tre volte le viti che devono risultare aderenti.
8b-1 ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR Center adapter brackets vertically on back of screen. Centre verticalmente los soportes en la pantalla. Centrez les supports à la verticale de l’écran. Richten Sie die Halterungen senkrecht mittig an der Bildschirm. Centreer de beugels verticaal op de van het scherm. centra le staffe verticalmente sul dello schermo. vycentrujte konzoly svisle na zadní obrazovky. vycentrujte konzoly zvisle na obrazovky. centre os suportes verticalmente no do ecrã.
8b-3 H (2) 8b-4 N 4mm wrench G K (4) K (4) G 8b-5 N 4mm wrench J (4) 23 2014-02-04 #:203-9371-2 (2014-04-11)
9 N 4mm wrench +20°/-5° ENG ESP FRN DEU NEL ITL ČEŠ SLK POR TÜR 24 2014-02-04 Tighten. Apretar. Serrer. Anziehen. Aandraaien. Stringere. Utáhněte. Utiahnite. Apertar. Sıkmak.
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product's manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
BESCHRÄNKTEN FÜNFJÄHRIGEN GARANTIE Peerless Industries, Inc. („Peerless”) übernimmt gegenüber den ursprünglichen Endnutzern von Peerless®-Produkten die Gewährleistung, dass diese unter normalen Einsatzbedingungen für fünf Jahre ab Datum des Kaufs durch den ursprünglichen Endnutzer (aber in keinem Fall länger als sechs Jahre nach Herstellungsdatum des Produkts) frei von Material- und Verarbeitungsfehlern sind.
OMEZENÁ PĚTILETÁ ZÁRUKA Peerless Industries, Inc. (“Peerless”) zaručuje původním koncovým uživatelům výrobků Peerless®, že budou bez vad na materiálu a provedení, za podmínky běžného používání, po dobu pěti let od data nákupu původním koncovým uživatelem (ale v žádném případě ne déle než šest let po datu výroby výrobku). Společnost Peerless dle své volby opraví nebo vymění, anebo proplatí cenu nákupu jakéhokoliv výrobku, který nebude v pořádku ve stavu, který tato záruka pokrývá.
BEŞ YILLIK SINIRLI GARANTİ Peerless Industries, Inc. (bundan sonra “Peerless” olarak anılacaktır) Peerless® ürünlerinde normal kullanım koşulları altında orijinal son kullanıcının satın alma tarihinden itibaren beş yıl süreyle (ama her halükarda ürünün üretim tarihinden itibaren en fazla altı yıl süreyle) malzeme ve işçilik arızaları olmayacağını orijinal son kullanıcılara garanti eder.