Installation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400 Model: HT642 Max Load Capacity: 100 lb (45.4 kg) 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer service at 1-800-729-0307. • This product should only be installed by a qualified professional.
Before you start make sure all parts listed are included with your product. A PARTS LIST A B C D E F G H I J K L M5 x 12 mm socket pin serrated washer head screw #14 x 2.5 wood screw 1 1 4 6 6 201-1601 201-1725 520-9521 510-1064 5S1-015-C03 4 mm security allen wrench M6 x 20 mm phillips pan screw spacer washer concrete anchor toggler 6-32 NYLOCK nut 1 4 1 4 6 4 4 560-1129 520-9402 590-1050 540-1008 590-0320 560-9708 530-1006 wall plate adapter bracket #14 x 2.
Attaching Adapter Bracket to Screen 1 Attach adapter bracket (B) to back of plasma screen using four M6 x 20 mm phillips screws (G). Screen 400 mm 400 mm B WARNING For installing HCS5610 Pay-Per-View Box, see step 2. For installing LST-4100B IP Interface Module, see step 3. 2 • Do not overtighten. Overtightening may cause permanent damage to the screen. Torque to 26-35 in • lb (30-40 kg • cm).
3 Installing LST-4100B IP Interface Module to Attachment Plate Note: Rubber grommets on the mounting tabs of LST-4100B will have to be removed before installing. Place LST-4100B onto the threaded studs on adapter plate (A) and secure with four 6-32 nylock nuts (L) using a 5/16" socket wrench. SCREEN L B LG MODEL LST-4100B (WITH FOUR MOUNTING TABS ATTACHED) Installation to Wood Stud Walls Use a stud finder to locate center of studs.
Installation to Solid Concrete and Cinder Block Wall WARNING A 5 concrete surface 1 5/16" (8 J J E Drill holes and insert anchors (J ). I A 2 WARNING E I J Place plate (A) over anchors (J ) and secure with screws (E). 3 WARNING Tighten all fasteners. not fig 5.3 J CUTAWAY VIEW INCORRECT concrete wall plate plaster/ dry wall CORRECT concrete wall plate I E plaster/ dry wall A fig 5.
Installation to Metal Stud WARNING • Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker. • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. 6 Using a stud finder, locate and mark the edges of the metal stud used in mounting this product. Use of an edge to edge stud finder is highly recommended. Use a level to draw a level, vertical line down the center of the stud.
Attaching Mounting Bracket Using Hook On Option 7 Attach four M5 x 12 mm serrated washer head socket pin screws (D) to the holes on the sides of mounting bracket (A) using the 4mm security allen wrench (F) provided. 7-1 Position slots of adapter brackets (B) onto the four M5 x 12 mm serrated washer head socket pin screws (D) attached to mounting bracket (A).
Mounting Bracket Using Tilt Option 8 Remove top two M5 x 12 mm socket pin serrated washer head screws (D) attached to wall plate (A). Loosen two M5 x 12 mm socket pin serrated washer head screws (D) in slot as shown in Detail 1. Once desired tilt is established tighten two M5 x 12 mm socket pin serrated washer head screws (D) in slots. D D D B D SLOT A Detail 1 9 of 9 ISSUED: 08-18-08 SHEET #: 125-9012-4 12-19-13 © 2010 Peerless Industries, Inc. All rights reserved.
