Installation User guide

ManualsBrandsPeerless-AV ManualsHardwareGC-PS3S

1 of 7

ISSUED: 1-17-11 SHEET #: 125-9181-1

Model: GC-PS3S

Installation and Assembly:

Lock Down Plate for PlayStation

3 Slim

Maximum Load Capacity:

10 lb (5.3 kg)

Peerless is a registered trademark of Peerless Industries, Inc.

Other parties’ marks are the property of their respective owners.

Peerless has no afliation with Sony Corporation of America.

Summary of content (7 pages)

PAGE 1
Installation and Assembly: Lock Down Plate for PlayStation® 3 Slim Model: GC-PS3S Maximum Load Capacity: 10 lb (5.3 kg) © 2011 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark of Peerless Industries, Inc. Other parties’ marks are the property of their respective owners. Peerless has no affiliation with Sony Corporation of America.
PAGE 2
A PARTS LIST A B C D E F G H I J B Description Qty. lock down plate 1 1/4-20 x 1.75" carriage bolt 4 #14 x 2.5" hex head wood screw 2 1/4-20 x 1.5" socket pin screw 4 concrete anchor 2 1/4-20 slope nut 3 plastic screw cap 4 4 mm allen wrench 1 1/4-20 plastic toggler 4 1/4-20 nylock nut 2 C D Part # 125-1217 520-1017 500-1005 520-1256 590-0320 530-0035 590-1294 560-9646 560-9708 530-9413 E H F I G J Installation to Wood Stud Wall..................................................................
PAGE 3
Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
PAGE 4
Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
PAGE 5
Installation to Metal Studs WARNING • Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker. • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. • Make sure that togglers are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended. 1 Using a stud finder, locate and mark the edges of the metal stud used in mounting this product.
PAGE 6
Installation to Drywall WARNING • Drywall must be 1/2" or thicker. • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. 1 Using lock down plate (A) as a template mark the center of the four mounting holes. Drill four 1/2" holes through drywall. NOTE: It may be necessary to drill 5/32" pilot holes prior to drilling 1/2" holes. Install togglers (I) as shown in figure 1.3. Loosely fasten lock down plate (A) to wall using four 1/4-20 x 1.
PAGE 7
Desktop Mounting Surface Lock down Installation 1 Place lock down plate (A) onto mounting surface as a template. Level, and mark the center of four rectangular mounting holes. Drill four 5/16” (8 mm) dia. holes through desktop mounting surface. Secure using four carriage bolts (B) though lock down plate (A) and mounting surface as shown in figure 1.1. Secure two 1/4-20 x 1 3/4” carriage bolts (B) using two 1/4-20 nylock nuts (J) in corners as shown in figure 1.1.