Installation and Assembly: Back to Back Ceiling Mount Model: DST965 * SEE NOTE * NOTE: DST965 WILL NOT WORK WITH ADJUSTABLE EXTENSION COLUMNS AEC006009, OR AEC012018 Maximum Load Capacity: 300 Ib (136 kg) 2300 White Oak Circle • Aurora, IL 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.
Before you start make sure all parts listed are included with your product. PARTS LIST Description A main cover B side cover C cable assembly D adapter bracket E component shelf clamp F bottom bracket G component shelf H M5 x 10 mm socket pin type-F screw I 1/4-20 X 2" socket screw J cable wire clamp K cable bracket L safety belt (not shown) M adapter plate N 4 mm security driver tool O interface bracket P tilt bracket Q M10 x 1.5 x 15 mm penta-pin™ screw R M5 x .
Some parts may appear slightly different than illustrated. J I K O M P N R Q S T U W V X Security Adapter Bracket Fasteners M4 x 12 mm (12) 510-1079 M5 x 12 mm (8) 520-1064 M4 x 25 mm (8) 510-1082 M6 x 30 mm (8) 520-1067 M6 x 12 mm (8) 520-1050 M6 x 25 mm (8) 520-1211 M8 x 15 mm (12) 520-1068 M6 x 20 mm (8) 520-9554 M8 x 25 mm (8) 520-1101 M8 x 40 mm (8) 520-1152 I.D. .22" (5.6 mm) (8) 540-1057 M5 x 25 mm (8) 520-1122 multi-washer (8) 580-1036 I.D. .34" (8.
1 Note: Notch indicates bottom of interface bracket (O) as shown in detail 1. Slide interface bracket (O) onto adjustable extension column (not supplied) and attach using fiber washer (V) and retaining collar (W) as shown in figure 1.1. Carefully thread retaining collar (W) onto end of extension column. Tighten retaining collar (W) at least four complete turns ending with one of the small holes aligned with slot in the end of extension column.
2 Screw eight M10 x 15 mm penta-pin screws (Q) into interface bracket (O) leaving approximately 1/4" of exposed thread as shown below and in detail 3. Q O O 1/4" Detail 3 Q Attaching Component Shelf 3 Secure two component shelves (G) to adjustable extension column (not supplied) using two component shelf clamps (E) and four 1/4-20 X 2" socket screws (I). NOTE: Make sure that component shelves are in the orientation as shown in detail 4.
4 Secure four M10 x 15 mm penta-pin screws (Q) through cable bracket (K), tilt plate (P), main cover (A), and adapter plate (M), and as shown below. Repeat with second support assembly. Q K P A TO P M 5 Hook tilt plate (P) and support assembly onto M10 x 15 mm penta-pin screws (Q). Repeat with second support assembly.
6 Run cable assembly (J) down through extension column around and through two cable brackets (K) as shown below. Secure cable to itself using u-bolt, clamp and nuts from cable wire clamp (J). CABLE C U-BOLT CLAMP NUT K 7 K Secure bottom bracket (F) to support assemblies using M5 x 10 mm socket pin Type F screws (H) as shown below.
Installing Adapter Brackets WARNING • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.
For Flat Back Screen 8-1 Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws. NOTE: Spacers may not be used, depending upon the type of screen.
Mounting and Removing Flat Panel Screen WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. 9 Hook adapter brackets (D) onto adapter plate (M), then slowly swing screen in as shown. Turn safety/security screws clockwise at least six times to prevent screen from being removed as shown in detail 5. Tighten using wrench (X). Screen can be adjusted horizontally if desired as shown in figure 9.1.
10 Secure PC component to component shelf (G) with safety belt (L) through slots on component shelf (G) using instructions provided with safety belt. PC COMPONENT 11 Thread four M5 x 10 mm socket pin Type F screws (H) into support assemblies leaving 1/8" of exposed thread. Repeat with second side. G SLOTS L H H 1/8" 12 Hook side cover (B) keyholes onto exposed screws.Tighten all M5 x 10 mm socket pin Type F screws (H). Repeat with second side cover.
