Installation and Assembly: 2 X 2 Wall Matrix Model: DS-VW646-2X2, DS-VW660-2X2 MAX 1 of 10 600 lb (272 kg) ISSUED: 09-22-11 SHEET #: 125-9248-3 04-01-13
PARTS LIST A B C D E F G H I J K L M N O P Q R S T U V B A DS-VW646-2X2 Description wall plate left connection bracket right connection bracket hook on bracket top adapter bracket bottom adapter bracket M6 x 12 mm phillips screw M8 x 15 mm phillips screw #14 x 2.
WALL PLATE ASSEMBLY 1 Attach two wall plates (A) together using left and right connection brackets (B and C) with eight M5 x 12 mm phillips screws (N), #10 flat washer (S), #10 lock washer (R) as shown below.
Installation to Wall Stud WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
3 NOTE: Determine Display being used and select orientation below. Fasten eight M5 x 12 mm phillips screws (N) into each hook on bracket (D) leaving 1/8" of exposed thread as shown below. Repeat step for all hook on brackets (D). D D OR N N 1/8" 4 1/8" Hook one bottom adapter bracket (F) onto exposed threads on hook on bracket (D) as shown below. Hook one top adapter bracket (E) onto exposed threads on hook on bracket (D) as shown below. NOTE: Do not tighten screws on hook on bracket (D).
ATTACHING ADAPTER BRACKETS TO DISPLAYS 5 Attach top and bottom adapter brackets (E and F) to back of displays using eight M6 x 12 mm phillips screws (G) with nylon shoulder washer (L), or eight M8 x 15 mm phillips screws (H), or eight M6 x 16 mm phillips screws (U) as shown below. NOTE: Make sure that nylon shoulder washer (L) is position as shown in detail 1. G, H or U L D E DISPLAY DETAIL 1 6 Un-hook hook on bracket (D) from top and bottom adapter brackets (E and F) as shown below.
7 Attach two hook on brackets (D) onto wall plate (A) as shown. Determine screen VESA mounting pattern and use measure plate (T) to space hook on bracket as show below. Repeat step with remaining two hook on brackets (D). 19.69" (500mm) 23.62" (600mm) ALIGN HOLES 7.87" (200mm) A D 3.94" (100mm) 15.75" (400mm) 11.81" (300mm) T MEASURE PLATE DETAIL 8 A Hook bottom adapter brackets (F) onto exposed threads on hook on bracket (D) as shown below. Repeat step with second display.
Hook one top adapter bracket (E) onto exposed threads on hook on bracket (D) as shown below. Repeat step with second display. E D E 10 Secure top adapter brackets (E) to hook on brackets (D) using four M5 x 10 mm socket pin type-F screws (M) in positions as shown below.
DS-VW646-2X2 11 Once displays are in desired position, secure using four security screws located on bottom of hook on brackets (D) as shown in detail 3. D SECURITY SCREW DETAIL 3 DS-VW660-2X2 11 Fasten four M5 x 25 mm socket pin screw (V) into bottom of hook on brackets (D) as shown in detail 4.
