DS-LED27BDL Series *Actual configuration may vary ENG Installation video for reference only. Read and follow instruction manual for full installation.
WARNING ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation. This product is designed to be installed on flat, unobstructed, vertical walls. Do not install on curved or angled walls. Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity.
ENG Tools Needed for Assembly. ENG To properly tighten screws: Tighten until screw head makes contact, then tighten another 1/2 turn. Do not overtighten screws. 1 2 5/32" (4mm) 3 3/8" (10mm) +1/2 4 2.
ENG Parts (Before beginning, make sure you have all parts shown below). A Parts List A B C D E F G H I J K L M N O P Q R S T B left column Description left column right column inside column vertical spacer horizontal spacer extrusion connector 3mm allen wrench two-tip T-handle M5 x 5mm set screw #14 x 1.
M top horizontal asy N bottom horizontal asy O P top left horizontal asy top right horizontal asy Q R bottom left horizontal asy bottom right horizontal asy 5 2020-04-13 #:146-9045-2 (2020-08-20)
1-1 G ENG Optional: If connecting two top horizontal extrusions, first remove inner hook-on brackets. M,O M,P ENG Remove and save hardware. 1-2 ENG Use extrusion connectors to connect top horizontal extrusions. 2.
1-3 G ENG Replace one hook-on bracket in between connected extrusions. M,O M,P ENG Use saved hardware. 2-1 G ENG Optional: If connecting two bottom horizontal extrusions, first remove inner hook-on brackets N,Q N,R ENG Remove and save hardware.
2-2 ENG Use extrusion connectors to connect bottom horizontal extrusions. 2.5mm N,Q F (3) H (6) N,R 2-3 G ENG Replace one hook-on bracket in between connected extrusions. N,Q N,R ENG Use saved hardware.
ENG This page intentionally left blank.
3 WARNING ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood may be covered by gypsum board (drywall) up to 5/8" thick. 3-1 ENG Use a laser level to keep mounting holes level.
3-2 7/8"(22mm) minimum for mounting clearance ENG Level top horizontal extrusion and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) 2.
3-3 1.75" (44mm) 5/32" (4mm) 5/32" (4mm) ENG Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). 3-4 ENG Level extrusion. Install using wood screws provided. 3/8" (10mm) I (5) N,P ENG Maximum 80 in. • lb (9 N.M.).
3-5 ENG Edges must be flush. ENG Secure vertical spacers to the wall flush with the horizontal extrusion.
3-6 ENG Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) 58.68" (149cm) D ENG Edges must be flush.
3-7 1.75" (44mm) 5/32" (4mm) 5/32" (4mm) ENG Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). 3-8 ENG Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then install using wood screws provided. 3/8" (10mm) I (5) N,R ENG Maximum 80 in. • lb (9 N.M.).
3-9 ENG Remove vertical spacer.
4-1 ENG Hook on and secure outer vertical columns. "L" and "R" markings designate left and right column. G ENG Tighten hardware.
4-2 ENG Hook on and secure all inside vertical columns. G ENG Tighten hardware.
5-1 G ENG Loosen hardware on vertical columns.
5-2 G ENG Plumb and level outer columns, then tighten hardware. Tighten hardware on four corner wall plates. ENG Tighten. ENG Tighten.
5-3 G ENG Tie a string between top slots on outer columns in order to level the depth of each vertical column. ENG Loosen, adjust, tighten. ENG Optional leveling for bowed walls ENG Loosen. ENG Insert. K ENG Tighten.
5-4 G ENG Tie a string between bottom slots on outer columns in order to level the depth of each vertical column. ENG Loosen, adjust, tighten. ENG Optional leveling for bowed walls ENG Loosen. ENG Insert. K ENG Tighten.
5-5 ENG Tighten or loosen to adjust height.
5-6 G ENG Adjust inner columns to fit horizontal spacers. Tighen column hardware after spacing. Start from the left column.
5-7 G ENG Continue adjusting inner columns to fit horizontal spacers until all are level.
5-8 ENG Remove all spacers.
6-1 G ENG Optional: For shallow depth installations, flip wall bracket orientation as shown. 2.25" (57mm) MIN 3.05" (77mm) MAX wall display tile wall display tile 2.60" (66mm) MIN 2.
6-2 ENG Level L brackets and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.
6-3 1.75" (44mm) 5/32" (4mm) 5/32" (4mm) ENG Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). 6-4 ENG Level L brackets. Install using wood screws provided. 3/8" (10mm) ENG Maximum 80 in. • lb (9 N.M.).
6-5 G ENG Tie a string between center slots on outer column in order to level the depth of each vertical column.
6-6 G ENG Adjust depth, then remove string. ENG Loosen, adjust, tighten.
7-1 T x3 S (4) ENG Display not included.
7-2 T ENG Attach display, tighten connecting hardware, and run cables one at a time starting from the bottom left.
7-3 T 21 16 22 11 17 23 12 18 7 13 6 24 19 25 14 8 9 15 10 34 2020-04-13 #:146-9045-2 (2020-08-20)
8 T ENG To remove, start from the top right.
ENG Warranty ITL Garanzia ESP Garantía ČEŠ Záruka FRN Garantie SLK Záruka DEU Garantie POR Garantia NEL Garantie TÜR Garanti̇ www.peerless-av.com/warranty Peerless-AV 2300 White Oak Circle Aurora, IL 60502 Email: tech@peerlessmounts.com Ph: (800) 865-2112 Fax: (800) 359-6500 www.peerless-av.com Peerless-AV Europe Unit 3 Watford Interchange, Colonial Way, Watford, Herts, WD24 4WP, United Kingdom Customer Care 44 (0) 1923 200 100 www.peerless-av.com Peerless-AV América Latina Av.
