DS-C555-4X3 46" - 55" (117 - 140 cm) MAX 1200 lb (545 kg) ENG 1 2015-06-24 #:009-9118-2 (2015-10-15)
This page intentionally left blank.
WARNING Do not begin to install product until you have read and understood the instructions and warnings contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product must be installed onto flat, hard, level surface to prevent tipping. The cart or stand is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. Displays must be removed before moving cart.
Parts (Before beginning, make sure you have all parts shown below).
M (6) N (1) O (1) dual cross support computer cover computer shelf P (3) R (3) extension adaptor bracket, 4x2 configuration Q (6) cord bracket S (6) knurled knob T (244) U (80) V (36) W (26) X (34) M8 x 16mm M8 square nut cover clip M5 x 10mm bar nut Y (1) 1/4" power bit Z (1) AA (48) BB (48) CC (1) 5mm allen wrench nylon shoulder washer M6 x 12mm 4mm allen wrench 5 2015-06-24 #:009-9118-2 (2015-10-15)
1-1 x6 B Z A (5mm) T (4) 1-2 x6 Do not fully tighten hardware U (2) T (2) SIDE VIEW 6 2015-06-24 #:009-9118-2 (2015-10-15)
2 x3 Z U (2) (5mm) U (2) D F T (4) U (4) U (2) F T (4) 7 2015-06-24 #:009-9118-2 (2015-10-15)
3 x3 TIGHTEN CONNECTING HARDWARE ENG FLUSH EDGES ENG Casters must be flush to end of horizontal leg support.
5-1 TIGHTEN CONNECTING HARDWARE x2 H 5-2 TIGHTEN CONNECTING HARDWARE Assemble middle support bracket.
6-1 x3 Do not fully tighten hardware T (4) P 6-2 X (2) TIGHTEN CONNECTING HARDWARE I (3) P (3) 10 2015-06-24 #:009-9118-2 (2015-10-15)
7 LOCK WHEELS TIGHTEN CONNECTING HARDWARE E E 8 x6 U (4) 1/8" (3mm) 1/8" (3mm) T (6) L 11 2015-06-24 #:009-9118-2 (2015-10-15)
9 a Use metric formula below and diagram to right to determine hole pattern required for center vertical support bracket. Repeat (x2). b All dimensions are metric.
10 L (3) R (3) DIS TIGHTEN CONNECTING HARDWARE PL AY H EIG HT L (3) DIS PL TIGHTEN CONNECTING HARDWARE AY H EIG HT 13 2015-06-24 #:009-9118-2 (2015-10-15)
11-1 TIGHTEN CONNECTING HARDWARE M (2) 14 2015-06-24 #:009-9118-2 (2015-10-15)
11-2 TIGHTEN CONNECTING HARDWARE M (2) 15 2015-06-24 #:009-9118-2 (2015-10-15)
11-3 TIGHTEN CONNECTING HARDWARE M (2) 16 2015-06-24 #:009-9118-2 (2015-10-15)
12 TIGHTEN CONNECTING HARDWARE T (2) K U (2) 17 2015-06-24 #:009-9118-2 (2015-10-15)
13 Center adaptor brackets vertically on back of screen. X .98" (25mm) 7.87" (200mm) 3.94" (100mm) 2.50" (63mm) 15.75" (400mm) X 2.50" (63mm) 0.
14-1 Must hang displays to bottom row first; Secure pin in "locked" position. "LOCKED" POSITION 14-2 Must hang displays on top row last; Secure pin in "locked" position.
14-3 Must hang displays on top row last; Secure pin in "locked" position. "LOCKED" POSITION 11-4 CC OPTIONAL: Insert M5 x 10mm type-F socket pin screws to lock latches.
Display Adjustment IN OUT SIDE SIDE TILT BACKWARD SIDE TILT RIGHT TILT LEFT TOP SIDE UP TILT FORWARD TOP DOWN ROTATE LEFT 21 ROTATE RIGHT 2015-06-24 #:009-9118-2 (2015-10-15)
12 TIGHTEN CONNECTING HARDWARE Q S Q S TOP VIEW 22 2015-06-24 #:009-9118-2 (2015-10-15)
12 I 13 1/8" (3mm) O N W (2) TIGHTEN CONNECTING HARDWARE O 23 2015-06-24 #:009-9118-2 (2015-10-15)
14 Route cables through cord brackets.
22 Display Removal Pull down on bracket cords and hold. Swing screen away from cart and lift to remove. 23 Remove displays from top row first.
24 Repeat step 22 to remove displays from middle row second. "UNLOCKED" POSITION 25 Repeat step 22 to remove displays from bottom row last.
This page intentionally left blank.
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product's manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
