DOG TRAINING COLLAR User Manual Model: PE-18 *Please read this manual before use
Contents 1. Warranty .......................................................................................... 01 2. Important safety information ...................................................... 01 3. Components .................................................................................... 03 4. Function ........................................................................................... 04 4.1 Remote transmitter.................................................................... 04 4.
info pecole.vip www.pecole.vip 1. Warranty This product has a warranty period of 1 year. The full details of the warranty and its terms applicable to this product can be found in www.pecole.vip. If you have any questions, please attach your order number to us: support@pecole.vip in your email and we will reply as soon as possible. Scan the QR code for more details. www.pecole.vip 2. Important safety information The warning and caution are used to remind you of potential dangers.
info pecole.vip www.pecole.vip Safety during training: your dog should have a strong leash. The leash should have a certain length, so as to enable your dog to chase an object and prevent your dog from reaching the road or other unsafe places. When your dog tries to chase, you must also have enough physical strength to restrain it. Dog training collar is not a toy, please keep it out of the reach of children. Caution It indicates a dangerous situation that, if not avoided, may cause injuries to your pet.
info pecole.vip www.pecole.vip 3. Components Remote transmitter Used to remotely control the receiver collar to train pets. Receiver collar Wear it on your dog to receive the command from the remote transmitter. USB charging cable Used to charge the remote transmitter and receiver collar. Wrist strap Install it on the remote transmitter to prevent loss. User manual Test light tool Detailed product specifications.
info pecole.vip www.pecole.vip Contact points 2 long contact points for dogs with thick hair 2 short contact points for dogs with short hair Sleeve on the contact point to Conductive silicone prongs make the contact point softer. 4. Function 4.1.
info pecole.vip www.pecole.vip Static Channel Display (1-4) Static Level Display(00-99) Warning Beep Battery Status (Receiver collar) Vibration Keypad Battery Status Level(0-9) Lock (Remote transmitter) 4.2.
info pecole.vip www.pecole.vip 4.3. Key definitions The remote transmitter rotates the switch ON&OFF switch knob and controls the strengthof (level regulator) vibration and shock.
info pecole.vip www.pecole.vip 4.4.
info pecole.vip www.pecole.vip 5. Product setting steps *In accordance with the following product steps before using the dog training collar. 5.1. Remote transmitter and receiver collar charging When the charging is completed, the green light will be on. 5.2. Installation of contact points and conductive silicone prongs 1. Select the correct contact points and length of conductive silicone prongs according to your dog's hair type.
info pecole.vip www.pecole.vip 3A 3B 5.3. Adjustable receiver collar 1. Untie the strap from the slide buckle (4A). 2. Adjust the slide buckle according to the size of the dog (4B). 3. Pass the strap through the slide buckle (4C). 4. Thread the excess strap through the buckle (4D). 4A 4B 4C 4D 5.4. Test 1. Turning on the receiver collar Press receiver collar button for 5 seconds until the green LED light flickers quickly.
info pecole.vip www.pecole.vip 2. Turning off the receiver collar Press receiver collar button for 3 seconds until the red LED light appear. Note: in order to prolong the battery life, please turn off the receiver collar when not in use. 3. Note: First press the vibration/beep/shock button next to the controller, and then adjust the strength through the switch knob of the controller to adjust the strength for vibration/beep/shock.
info pecole.vip www.pecole.vip 5.5. How to use the test light tool 1. Shock function test - Turn on the receiver collar. - Attach the contactor of the test light tool to the contact points (or conductive silicone prongs). - Press the shock button, and the test light tool will light up. It will light up according to the increase of shock degree. 2. As a tool for tightening or loosening the contact points 5.6.
info pecole.vip www.pecole.vip 3. Controller pairing: press and hold the channel selection button D to pair the receiver collar. D 4. Pairing succeeded: the receiver collar will beep and the green light will flash slowly. 5.7. Installing the receiver collar NOTE: The contact point must directly contact the skin of the dog's neck, check the tightness of the receiver collar, and insert two fingers tightly between the receiver collar and neck.
info pecole.vip www.pecole.vip 5.8. Turning on the remote transmitter and receiver collar Rotating the regulator A “A” to turn on the remote transmitter Press the button to turn on the receiver collar, the green LED flashes When the collar is not used, please turn off the remote transmitter and receiver collar to increase the battery life. (Press the button for 3 seconds to turn off the receiver collar) 5.9.
info pecole.vip www.pecole.vip 5.10. Three training mode instructions 1. Beep instruction Give an instruction to the receiver collar to beep at a unadjustable volume 2. Vibration instruction A B Give a vibration instruction to the receiver collar. Adjustment of vibration strength: hold down the vibration level button B and simultaneously rotate the level regulator A of the remote transmitter.
info pecole.vip www.pecole.vip 3.Shock instruction A C Static Static + 5.11. Multiple receiver collar systems (NOTE: If you only use one receiver collar, please skip this step. This setting only applies to multiple receiver collar with one remote transmitter.) Step 1: Pairing the 2nd, 3rd or 4th receiver collar. (NOTE: You should buy an extra receiver collar.) Receiver collar: Make sure the receiver collar is turned off. Press and hold the switch for 5 seconds until the green light flashes quickly.
info pecole.vip www.pecole.vip Step 2: Receiver collar switching You can train 4 dogs by switching channels. Press and hold the pairing/channel selection button D, and simultaneously rotate the level regulator A to select the dogs to be trained. A 4 D Press and hold Step 3: Reset all paired receiver collars. Make sure the remote transmitter is "ON". Press and hold the button B and C, turn the regulator switch A from OFF to ON.
info pecole.vip www.pecole.vip 5.12. Matters needing attention in pet training 1. Select contact points andconductive silicone prongs. For the best effect, please choose the right contact point according to your dog's coat. For dogs with thick hair, please use 2 long contact points and conductive silicone prongs. For dogs with short hair, please use 2 short contact points and conductive silicone prongs. 2.
info pecole.vip www.pecole.vip 6. Frequently asked questions The answers to these questions may help you solve most of the problems on the dog training collar. If your problems cannot be solved, please contact our customer service center. 1. My pet doesn't respond - Check whether the receiver collar is turned on. when I press the beep, - Please check whether the battery in the reremote transmitter is low. vibration or shock button. - Put the test light tool provided in the kit on the receiver collar.
info pecole.vip www.pecole.vip 7. Replacement parts and accessories Replacement parts or accessories for your dog training collar can be purchased by visiting www.pecole.vip or by contacting our Customer Care Center at support@pecole.vip.
Scan the QR code for more details. www.pecole.vip service pecole.vip PECOLE Dog Training Collar Model: PE-18 Manufacturer: Dongguan Dirui Electronic Technology Co., Ltd.
