Install Instructions

ManualsBrandsPeco Controls ManualsHeating SuppliesPerformance PRO T8000 Programmable 2H/2C Thermostat



Thank you for choosing a PECO



Performance PRO™ thermostat. The Performance

PRO T8000 Series is intended for use in residential and commercial environments. It

is designed for and can support up to 3-HEAT/ 2-COOL con gurations in conventional

systems and in heat pump applications. The Performance PRO also provides the

capability to meet the requirements for ASHRAE 90.1-2004 and California Building Code

Title 24 (2008 edition).

The Performance PRO T8000 Series is comprised of the T8000 non-programmable

thermostat models and the T8500 programmable thermostat models. The T8000 Series

features an 8 square inch blue backlit display with dynamic menus, accessed using soft

keys. All Performance PRO T8000 Series offer the following standard features: auto-

changeover, temporary override, optional remote sensors, occupancy sensors, three

levels of keypad lockout, a PIN access code, a furnace  lter change reminder, and a heat/

cool Demand Indicator. In addition, the T8500 programmable models contain: up to four

scheduled events per day, a 365-day calendar, 20 holidays, holiday override, temporary

override, a Power Harvesting feature to preserve battery life (also known as “power

stealing”), Secure Digital (SD) card capability (card not included), and optional humidity

control (T8532-IAQ only).

The T8000 Series can be powered by 24 VAC or batteries or both (recommended). The

T8000 Series can control up to 7 outputs and monitor three external sensors. The T8000

Series mounts onto any PECO Performance PRO Series wallplate.



The PECO Performance PRO thermostat is intended for use in conventional and heat

pump applications.

• System mode selections: Off-Heat-Cool-Auto-Emergency

• Stages: 1 Heat/1 Cool, 2 Heat/1 Cool, 1 Heat/2 Cool; 2 Heat/ 2 Cool; 3 Heat/ /2 Cool

• Fan control: Cycling (Auto) or Continuous (On); 1 Speed

• Permanent memory: All device settings are stored in permanent memory.

• Connections for Remote Sensors (indoor, outdoor, and occupancy)

• SD card capability (card not included)



• 

• 

• 





Temperature Control

Range: 50° to 90° F (10° to 32° C)

Differential: 1° F (0.5°C)

Input Power: 24 VAC (20-30 VAC) 50/60 Hz (+/- 10%) or AA alkaline batteries

(both recommended); 5mm terminals accept 14-24 AWG

stranded or solid wire.

Operating Temperature: 0° to 120°F (-17° to 48°C)

Shipping Temperature: -20° to 130°F (-28° to 54°C)

Operating Humidity: 5% to 95% RH, non-condensing

Physical Dimensions: T8000/T8500 Thermostat: 4.3” H x 5.7” W x 1.3”D

with 3.2” x 2.5” / 8 square inch liquid crystal display (LCD)

Output Ratings

Voltage (50/60 Hz): 20-30 VAC

Current: 0.02-1.0 A per terminal; W1 (B/O), W2 (AUX), G, A, E, Y1, Y2.

Note: Collectively, total current draw must not exceed 2.5 A.



Select an appropriate thermostat location

Locate the thermostat about four feet (1.2m) above the  oor on a wall in an area with good

ventilation and an average temperature, where it will be responsive to changes in room

temperature.

The Performance PRO T8000 Series may be mounted on a:

• Horizontal or vertical 2” X 4” device box

• Horizontal 4” X 4” device box

• Flat surface

Do  locate the thermostat where it can be affected by:

• Direct sunlight

• Drafts or dead areas behind doors

• Radiant heat from appliances

• Concealed pipes or chimneys

• Outside walls or unheated/uncooled areas

Required components (not included, unless otherwise speci ed):

• Two new AA batteries (included)

• Screws and wall anchors (included)

• Screwdrivers: Phillips (for wallplate); small  athead (for terminal blocks)

• Drill with 3/16” drill bit (or 7/32” for plaster)

• Wirecutter and stripper

• Level

• Performance PRO T8000 Series Thermostat (included)

• Performance PRO T8000 Series Thermostat Operating Manual (included)













• READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL,

OPERATE OR SERVICE THIS THERMOSTAT.

• Failure to observe safety information and comply with instructions could result in

PERSONAL INJURY, DEATH AND/OR PROPERTY DAMAGE.

• To avoid electrical shock or damage to equipment, disconnect power before

installing or servicing and use only wiring with insulation rated for full thermostat

operating voltage.

• To avoid potential  re and/or explosion do not use in potentially  ammable or

explosive atmospheres.

• Retain these instructions for future reference.

• This product, when installed, will be part of an engineered system whose

speci cations and performance characteristics are not designed or controlled

by PECO. Review applications and national and local codes to assure that the

installation will be functional and safe.

▲



▲



Mounting holesMounting holes

Figure 2. T8000/T8500 Thermostat

back view (with wallplate attached).

Wiring passage

Digital display with blue backlight

Override key

Keypad Lockout,

Battery Indicator,

Service

Indicator,

SD Card

System Mode

System key

Temperature

(indoor)

Current day

Up and Down

keys ▲/ ▼

Fan key

More key

Current time

Demand

indicator

Fan (On/Auto)

Recovery mode

Setpoint

temperature

Figure 1. T8000/T8500 Thermostat

(Home Display)

Summary of content (12 pages)

PAGE 1
PerFormance Pro t8000 serIes InstallatIon GUIDe ▲warnInG the Peco PerFormance Pro thermostat ! Thank you for choosing a PECO® Performance PRO™ thermostat. The Performance PRO T8000 Series is intended for use in residential and commercial environments. It is designed for and can support up to 3-HEAT/ 2-COOL configurations in conventional systems and in heat pump applications. The Performance PRO also provides the capability to meet the requirements for ASHRAE 90.
PAGE 2
Part I: Install the wallPlate 1. Position the wallplate on the wall with the directional arrow pointing up (see Fig. 3) and terminal blocks facing outward. Figure 3: Position wiring passage the wallplate on the wall. Pull wires through wiring passage.
PAGE 3
System Type 11: 3H/2C Heat Pump System Type 12: 3H/1C Conventional TERM Function TERM Function C Common C Common B/O Reversing Valve W1 Heat 1 AUX Auxiliary Heat W2 Heat 2 G Fan G Fan A Economizer/Damper A Economizer/Damper E Emergency Heat E Heat 3 Y1 Compressor 1 Y1 Cool 1 Y2 Compressor 2 Y2 RH Power for Heating RH Power for Heating RC Power for Cooling RC Power for Cooling Part Iv: Install BatterIes & remove taB 1.
PAGE 4
3. Part vIII: moUnt the t8000 onto the wallPlate 1. Position the thermostat slightly above the mounted wallplate (see Fig. 9), then secure the hooks on the back side of the thermostat to the hinge pockets on the wallplate. note: the top back side of the thermostat should slip into the hinge pockets easily. Do not use excessive force. In Service Menu 610, press ▲/ ▼to select option “01,” Heat Stage 1 (see Fig.12).
PAGE 5
taBle 2. aDvanceD conFIGUratIon: servIce menUs To access Service Menus, simultaneously press lower left and lower right keys. Changed values are automatically retained. Service Menu availability is dependent upon system type and upon system configuration. menU FeatUre oPtIons stD. moDel DeFaUlt DescrIPtIon / comments 100* Schedule Format 0-3 1 Select the schedule format on the T8000 Series. (Menu not available on non-programmable thermostats.
PAGE 6
taBle 2. aDvanceD conFIGUratIon servIce menUs (cont.) menU FeatUre oPtIons stD.moDel DeFaUlt 290 Range Low 50-90 °F or 10-32°C 50°F (10°C) Choose the lowest selectable temperature setpoint value. 300 Range High 50-90 °F or 10-32°C 90°F (32°C) Choose the highest selectable temperature setpoint value. 310 Setback Low Off; 50-82°F or 11-27°C 55°F (13°C) Select the heat setpoint for setback mode.
PAGE 7
taBle 2. aDvanceD conFIGUratIon servIce menUs (cont.) menU FeatUre oPtIons stD.moDel DescrIPtIon / comments DeFaUlt 450 Cycles Per Hour (CPH) Emergency Heating & Stage 3 Heat 0-12 CPH 5 CPH Defines the number of cycles per hour for heating. Select 0 to enable ON-OFF control for Emergency Heating & Stage 3 Heat. 460 Heat Recovery Rate 0-18°F/Hr 0-10°C/Hr 5°F/Hr Defines the rate at which the device achieves the heat comfort setpoint. Select 0 to disable ramp recovery.
PAGE 8
taBle 3. troUBleshootInG & FreqUentlY askeD qUestIons In case of difficulty, try one of the following suggestions below. symptom Potential cause(s) solution If display screen is blank • Thermostat is not being powered • Check to assure connection between Common (C) and (RC) for 24 VAC. • Check to assure that the metal jumper connects “RC” and “RH” (on single transformer system only). • Check to assure AA batteries are installed properly and are charged.
PAGE 9
Part X: set PIn access For servIce menUs (oPtIonal) t8000 serIes PerFormance Pro accessorIes: sensors Creating a PIN access code allows the installer to restrict access to Service Menus. First, a PIN access must be enabled in Service Menu 341; second, a three-digit code must be created in Service Menu 342. After these two Service Menus are properly configured, the thermostat requires the user to enter a PIN access code to enter the Service Menus.
PAGE 10
locate & moUnt Peco InDoor remote Zone sensor (sP155-017) 2. mount subbase. Remove Zone Sensor cover from the subbase, and mount subbase on the wall or in a 2’ X 4” device box. Route the wires through the wire access hole in the subbase (see Fig. 22). Seal the hole in the wall behind the subbase. ▲ ! warnInG Figure 22. Mounting the SP155-017 Indoor Remote Zone Sensor. Wall mounting • READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE, OR SERVICE THIS SENSOR.
PAGE 11
If the Indoor Remote Zone Sensor is working properly, the primary display (center) shows the correct temperature taken at the location where Indoor Remote Zone Sensor is currently installed (see Fig. 25). InstallatIon Use the following steps to mount the Outdoor Remote Sensor. steP 1 Figure 25. Thermostat Display shows temperature from Zone Sensor if working properly. steP 2 troUBleshootInG: InDoor remote Zone sensor If the thermostat Home Display appears as follows (see Fig.
PAGE 12
wIre Peco oUtDoor remote sensor heat PUmP temPeratUre lockoUts note: The options available in Service Menu 140 (below) are dependent on the selected System Type, Service Menu 110. 1. Wire the PECO Outdoor Remote Sensor (P/N 70327) to Terminal S3 and Sensor Common (SC) on the thermostat backplate (see Fig. 27). note: See Table 1 for terminal designations for the Indoor Remote Zone Sensor. 2. Assure that Step 6 (previous section) is complete and the PECO Outdoor Remote Sensor is secure. 3.