Accessory List

ManualsBrandsPeco Controls ManualsHeating SuppliesRemote Sensor for TAC Erie Thermostat

CP-9301-xxx Series, CP-9302-xxx Series

Electronic Actuator Drive

Model Chart

Units with a “-2” suffix, e.g. MP-xxxx-xxx-2-x, include a built-in transformer (used for Microtherm

or with AE-504) with secondary leads wired externally to terminals 7 (Blue, 12 Vac) and 8

(Red, 24 Vac) of the actuator.

Caution:

When using the CP-9301 or CP-9302 with actuators containing an

internal transformer,

disconnect and tape off the red and blue leads before installing and powering the device.

Failure

to do so can result in damage to the actuator drive

Note:

Models prior to “-2” suffix had transformer wired directly to potentiometer. To disconnect the transformer, remove the back plate of the actuator, then disconnect and tape the transformer

leads.

The CP-9301 and CP-9302 electronic actuator drives

process a variable input signal from a controller to provide

proportional control of an electric gear train actuator. The

CP-9301 is preset at the factory for voltage input. The CP-

9302 is factory preset for current input and has additional

wiring for connection to an override switch, for those

applications requiring an external override of the input

signal. These drives are equipped with built-in jumpers

and adjustable potentiometers, so that the type of input

signal, deadband, input span, and start point may be reset

in the field when necessary.

Features:

• Mounts directly onto TAC proportional, electric, gear train actuators.

• Power is supplied directly from the actuator.

• Jumpers for selecting either voltage or current input, as well as 3%

or 5% deadband.

• Adjustable span and start point potentiometers.

Part Number

Input Signal

Override

Factory Jumper Settings Jumper Settings

Potentiometer

Adjustment Ranges

Input

Signal

Deadband Start Point Input Span

Input

Signal

Deadband Input Span Start Point

CP-9301

Not Available

Voltage

(6 to 9 Vdc)

3% of Input

Span

6 Vdc 3 Vdc

Voltage

Current

3% or 5% of

Input Span

3.0 to 16.5

Vdc or 8 to

16 mAdc

0 to 10 Vdc

or 2 to 16

mAdc

CP-9301-456

Voltage

(0 to 10

Vdc)

0 Vdc 10 Vdc

CP-9302 Available

(Use is

Optional)

Current

(4 to 20

mAdc)

4 mAdc 16 mAdc

CP-9302-702

5% of Input

Span

Typical Actuators.

Actuator Series

Power Torque

Stroke

Degrees

Spring

Return

Internal

Transformer

Vac

60 Hz

Amp Lb-in. N-m

MP-2113-500 24 2.2 50 5.6 180 ⎯ No

MP-361 24 2.5 50 5.6 180 CW No

MP-371 24 2.5 50 5.6 180 CCW No

MP-381 24 2.5 220 24.9 180 ⎯ No

MP-9713 24 4.0 800 90.3 180 ⎯ No

MP-465 120 0.5 50 5.6 180 CW Yes

MP-475 120 0.5 50 5.6 180 CCW No

MP-483 120 0.5 220 24.9 90 ⎯ Yes

MP-485 120 0.5 220 24.9 180 ⎯ Yes

MP-495 120 0.95 450 50.8 180 ⎯ Yes

MP-9750 120 0.9 800 90.3 180 ⎯ Yes

MP-4651 240 0.25 50 5.6 180 CW Yes

MP-4851 240 0.25 220 24.9 180 ⎯ Yes

9301

xxx

Series,

CP-9302

xxx Seri