User Manual

9
Front Panel
HIGH
HIGH MID-MORPHLOW
LOW
MONITOR
MONITOR MID
EFFECTS
LEVEL
1
CH. 1
min max
min max
min max
clip
sig
min max
high
min max
LEVEL
2
CH. 2
min max
min max
min max
clip
sig
min max
high
min max
LEVEL
3
CH. 3
min max
min max
min max
clip
sig
min max
high
min max
LEVEL
4
CH. 4
min max
min max
min max
clip
sig
min max
high
min max
LEVEL
5
CH. 5
min max
min max
min max
clip
sig
min max
high
min max
LEVEL
6
CH. 6
min max
min max
min max
clip
sig
min max
high
min max
LEVEL
7
CH. 7
min max
min max
min max
clip
sig
min max
high
min max
LEVEL LEVEL LEVEL LEVEL
8
CH. 8
min max
min max
clip
sig
min max
min max
min max
USB MEDIA PLAYBACK
DIGITAL EFFECTS
Press to Select
Press to Select
EFX
SELECT
MEDIA
SELECT
MIC
EFX
MUTE
DEFEAT
efx clip
IN
USB
USB MEDIA
+12
+6
0
-6
-12
63 125 250 500 1K 2K 4K 8K 12K
FLS FEEDBACK LOCATING SYSTEM
SIGNAL
MONITOR
+12
+6
0
-6
-12
63 125 250 500 1K 2K 4K 8K 12K
FLS FEEDBACK LOCATING SYSTEM
SIGNAL
MAIN
KOSMOS-C MONITOR MAIN
min max
min/o max
min max
EFX TO MON
-6
-12
LIMIT
-18
-24
-30
-6
-12
LIMIT
-18
-24
-30
31 32
36 3735
33
38
34
39
DIGITAL EFFECTS LCD DISPLAY
e top row of this LCD displays the currently selected Eect and the bottom row displays the status of the media inputs of channel 8. If chan-
nel 8 is in “USB” mode, it can also be used for navigating the folders on the USB drive or displaying the current song playing.
EFX SELECT
e EFX select knob is used to navigate through the EFX presets. Turning the encoder changes the selection in the display. e new selection
will be blinking in the display, push the EFX Select encoder to choose the new eect. Once the eect has been selected, you can now edit the
eect. To do this, press the EFX Select encoder, the display will change to the current parameter setting of the preset. Turn the EFX Select en-
coder to change the parameter up or down. Press the encoder again to exit the parameter edit mode. To restore the EFX presets back to factory
settings, press and hold the EFX Select encoder for 5 seconds and select "Y" when prompted.
EFX DEFEAT
is button mutes the eects being sent to the main mix and monitor mix, allowing the user to listen to a dry signal at the main outputs.
When muted, the switch will be red. is can also be activated with a momentary footswitch. See (53).
EFX CLIP
is LED blinks red when the signal being sent to the eects section is too high and is causing distortion. Find the source of the hot signal by
reducing the EFX send (7) on each channel until the LED is no longer lighting (blinking red).
REW/PREV
A short press will rewind to the beginning of the current song. Pressing this button twice will take you to the previous song on the USB drive.
A long press will rewind through the current song, release to play when you reach the desired spot in the song.
PLAY/PAUSE
e play/pause button toggles the current song between play and pause. When the > is displayed, the song will be playing. When II is dis-
played, the song is paused.
FF/NEXT
A short press will advance the media player to the next song on the USB drive. A long press will fast forward through the current song, release
to play when you reach the desired spot in the song.
MEDIA SELECT
Once a USB device is connected in channel 8, you can use the “Media Select” encoder to navigate through the folders/songs on the drive. Once
the desired le is displayed on the screen, press the Media Select knob to cue that le. Use the controls on the mixer for play, pause, forward
and reverse.
MIC MUTE
Depressing this button mutes the mic/line inputs in all 8 channels. e media inputs (RCA and 3.5mm) jacks on channel 7 and the USB/BT
inputs on channel 8 are still “live”. is allows you to play break music, while muting all of the microphone inputs.
31
32
33
34
35
36
37
38
39