PV®10AT • PV®BT Compact Mixer 1/4”-Hi-Z CH.4 Only MAIN OUTPUTS USB A L DIRECT OUT DIRECT OUT DIRECT OUT 5 AUX SEND DIRECT OUT L 2 3 4 PV 10AT R R 6 5/6 9 L 10 R R STEREO IN PAIRING 1 L FS 3.
FCC/ICES Compliancy Statement This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS Standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, that may cause undesired operation. Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence.
ENGLISH PV®10AT and PV®10BT Compact Mixers Congratulations on purchasing the Peavey PV®10AT or PV®10BT Compact Mixer. The PV®10AT and PV®10BT are studio-quality mixing consoles designed to meet diverse needs while occupying a small space. These are the perfect consoles for small venue performances or home recording environments.
DIRECT OUT DIRECT OUT DIRECT OUT PV10AT Front Panel (channels 1 and 2) 1 1 1 This combination input jack accepts a ¼” or XLR balanced plug. The XLR balanced input is optimized for a microphone or other low impedance source. The ¼” input is a TRS balanced type, and also accepts ordinary TS guitar cables.
PV10AT Front Panel (channels 1 and 2) 13 EFX SEND This control adjusts the level of the channel signal added to the effects mix. The signal is sent to the internal effects processor. Turning the knob to the left (min) will turn off effects on the associated channel, while turning the knob to the right will increase the amount of the selected effect. The effects send signal is taken after the channel level (18) so that adjustments made to the fader will also affect the send level.
USB A FS 3.5mm STEREO PV10AT/PV10BT Front Panel (channels 5, 6, 7 and 8) DIRECT OUT 22 DIRECT OUT L DIRECT OUT DIRECT OUT 22 4 PV 10BT STEREO INPUTS DIRECT OUT DIRECT OUT USB MEDIA JACK R USB A 6 5/6 7/8 3.
PV10AT/PV10BT Front Panel (channel 4) 32 1/4”-Hi-Z CH.4 Only MAIN OUTPUTS USB A FS 3.5mm STEREO L ECT OUT 5 31 AUX SEND DIRECT OUT L 3 0BT 29 4 R 6 5/6 9 L 10 R R STEREO IN PAIRING R L 7/8 9/10 10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTH 33 34 35 ANALOG BALANCE CONTROL Controls the balance between the analog channels 5/6. 30 Controls the balance between the digital channels 7/8.
0AT 10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTH PV10AT Front Panel 36 Auto-TUNE HI PASS ELECTRIC GUITAR PRE-SHAPE L HI PASS GAIN max min GAIN 9/10 R PHANTOM POWER 48V USB B min 37 PV 10 USB A Bluetooth max min max STEREO IN LEVEL CONTROL ROOM L SOLO/MAIN A/B SELECT min 0 min - 0 + max HIGH 0 - + max min HIGH - + max min - max + max HIGH 0 min max min max LEVEL A/B max AUX39 EFX c 39LEVEL RECORD 40 ROOM 41 TO CONTROL 44 USB
T h x t E 2 Auto-TUNE HI PASS L HI PASS min GAIN max min GAIN 9/10 R B PV10AT FrontUSB Panel PHANTOM POWER 48V USB A Bluetooth max PV 10 min min 0 min - + max min - - MID-MORPH 0 min + max min - -LOW+ max EQ BYPASS - low GAIN + max min - + high min - -LOW+ + max 45 min min EQ BYPASS + max - max min max LEVEL A/B RECORD LEVEL min max min max R A A/B SELECT B/ REC B/REC REC LEVEL USB TO CONTROL ROOM -LOW+ + max min -LOW+ Press to Select
PV10AT Front Panel EFX Select Knob: EFX Mode: In EFX Edit Mode (see Auto-Tune Switch), the EFX Select knob is used to navigate through the EFX presets. Turning the knob changes the EFX preset in the display. The new selection will be blinking in the display; push the EFX Select knob to choose the new effect. Once the effect has been selected, you can now edit the effect. To do this, press the EFX Select knob and the display will change to the current parameter setting of the preset.
The display will now change to the current Detune setting. Turn the EFX Select knob to change the Detune setting. The Detune setting determines how the Auto-Tune pitch correction is calibrated. When the Detune setting is 0 cents, this means the Auto-Tune is calibrated to the standard A440, or where the note A4 equals 440 Hz. The range of the Detune setting is -64 to 63 cents, a width of 128 cents.
ax gh H ax ax ax ht TE 2 min + max HIGH min - - low min - + high 0 -LOW+ max EQ BYPASS - low min - + high max min min MID max min MID 0 min EQ BYPASS max RECORD LEVEL min USB max TO CONTROL ROOM 0 -LOW+ min MEDIA SELECT 52 -LOW+ Press to Select or edit max 0 max EFFECts media Press to Select PV10AT + - + Front- Panel 0 -LOW+ + max HIGH 0 MID-MORPH min + max HIGH 0 MID-MORPH min + max HIGH 0 53 max 54 EFX SELECT 55 USB MEDIA PLAYBAC
PV10AT Front Panel 58 STEREO/MONO MODE SWITCH In the mono position, the left and right buses are summed together after the faders. In this position, the L fader controls the level of the L bus, and the R fader controls the level of the R bus, allowing you to use the L and R buses as groups. For example, all vocals could be panned L and all instruments panned R. Then the L fader becomes the vocal master level and the R becomes the instruments master level.
- low + high MID-MORPH 0 min -LOW+ 63 MID-MORPH 0 max EQ BYPASS - low + high min -LOW+ max EQ BYPASS low - + high MID-MORPH 0 low - + high MID-MORPH min - + max MID 0 max EQ BYPASS min max - min min EQ BYPASS -LOW+ Press to Select or edit MEDIA SELECT 0 max EFFECts media Press to Select MID 0 PV10AT Front Panel -LOW+ -LOW+ -LOW+ min min + max EFX SELECT max USB MEDIA PLAYBACK DIGITAL EFFECT/MEDIA PLAYBACK KOSMOS-C HIGH CONTROL A very selective high fre
PV10AT/PV10BT 67 68 POWER ON 67 69 DIGITAL AUDIO PORT COMPUTER DC POWER INLET Use to connect the included power supply. Be sure the power supply is connected to the PV®10 before connecting to a power source. Use 15VDC, 1A adapter only. Replace only with Peavey part number 30908119. 68 POWER SWITCH This is the main power switch. 69 USB PORT TYPE B The USB port is used to connect the PV® Series USB mixer to a computer for recording or playing back digital audio to/from your computer.
4 3 2 CHANNEL 9/10 RIGHT LEFT ON/OFF STATUS BLUETOOTH INPUT USB B Streaming Input USB A Media Player Input CHANNEL 7/8 3.
PV®10AT & PV®10BT Series Specifications Mic pre EIN = -126 dBu @ max gain with 150 ohm source Inputs Function Microphone (150 ohms) Min** Input Levels Nominal* -71 dBu -51 dBu Min Gain (4 dB) -17 dBu +5 dBu +16 dBu Input Z Input Gain Setting 2 kΩ Max Gain (59 dB) (ohms min) Max Bal/ Unbal Connector -39 dBu Bal XLR Pin 1 Gnd Pin 2 (+) Pin 3 (-) Bal 1/4" TRS; Tip (+) Ring (-) Sleeve Ground Unbal 1/4" TS; Tip (+) Sleeve Ground Unbal 3.
Gain Mic Input Gain Adjustment Range: 4 dB to 59 dB Mic Input to Left/Right Balance Output 79 dB (max gain) Line Input Gain Adjustment Range: -16 dB to 40 dB Line Input to Left/Right Balance Output 60 dB (max gain) Stereo 5/6 1/4" Gain Adjustment Range: Off to +18 dB Stereo 5/6 1/4"to Left/Right Output 42 dB (max gain) Stereo 5/6 3.5mm / RCA Gain Adjustment Range: Off to +28 dB Stereo 5/6 3.
Crosstalk/Attenuation Adjacent Input Channels (1 kHz) >90 dB Mute Button Attenuation (1 kHz) >90 dB Left to Right Outputs (1 kHz) >70 dB Channel Fader Kill (1 kHz) >85 dB Common Mode Rejection Ratio (Mic Input) 50 dB minimum (20 Hz to 20 kHz) 70 dB typical @ 1 kHz Meters 6 segment, peak reading (0 db = +4 dBu) Signal/Overload Indicators Red LED lights 5 dB below clipping Dimensions 12.75" wide x 15.1" deep x 2.1875" high (32.39 cm x 38.35 cm x 5.56 cm) Weight PV10BT: 8.22 lbs (3.
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: 11/01/2011 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
U.S. CUSTOMER WARRANTY REGISTRATION Optional Product Extended Warranty Registration Give us some information and put your extended warranty into effect! Please take a few minutes to fill out this information/survey sheet to help us get to know and serve you better. To save time, submit your warranty registration online at www.peavey.com/support/warrantyregistration 1. 7.
