Instructions / Assembly

1. Unpack the contents of the box and check to make sure that all items are accounted for and in good condition.
2. Select a flat, level surface for the assembly and final location of your fountain.
3. Position the part A over the part B and align the notch which is on the bottom corner of the part A with the radial corner which is on the top of the
part B. Connect the light power cable and insert the water tube into the pump outlet that is on the top of the pump. Place the pump upright into the
fountain body. Lead the pump power cord through out the gas of between the board of part A and Part B. Insert the Part A into the Part B.
Connect the pump with transformer until the parts are secured together (Fig.1)
4. Add clean water into the Part B. The water level should be approximately 1 in. / 25 mm lower than the edge of the basin. Connect the
transformer to a GFCI outlet and the product will begin to function as intended. (Fig. 2)
5. If the pump runs with low or high water circulation Check and adjust the regulator dial or slide on the front of the pump. Adjust the dial/slide
towards (+) to increase water flow or towards (-) to decrease water flow. (Fig. 3)
6. To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing after the initial setup of your fountain.
It is highly recommended that this fountain be placed in an area where it cannot be damaged that might cause damaged with the fountain .
7. Do not leave your fountain running for extended periods of time when no one is present to observe the performance.
8. Check the area around your fountain on a regular basis to ensure that there is no leakage.
IMPORTANT SAFETY INSTRUCTIONS
TRANSFORMERS
When using electrical products, basic precautions should always be practiced including the following:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2. Read and follow all instructions that are on the product or provided with the product.
3. For a cord-connected or direct plug-in power unit, do not use an extension cord.
4. Reference the National Electrical Code, ANSI/NFPA 70, specifically for the installation of wiring and clearances from power and lighting
conductors.
5. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including
fire-rated construction.
6. For a cord-connected or direct plug-in power unit, do not install or use within 3.05 m / 10 ft of a pool.
7. For a cord-connected or direct plug-in power unit, do not use in a bathroom.
8. For a cord-connected power unit, user should pay attention to below statement
WARNING: Risk of Electric Shock. When used outdoors, install only to a covered Class A GFCI protected receptacle that is weatherproof
with the power unit connected to the receptacle. If one is not provided, contact a qualified electrician or proper installation. Ensure that the power
unit and cord do not interfere with completely closing the receptacle cover.
9. WARNING: Risk of Fire. Installation involves special wiring methods to run wiring through a building structure. Consult a qualified
electrician.
10. For a unit intended to be mounted greater than 0.3 m / 1 ft from the ground surface:
WARNING: Risk of Electric Shock. Mount the unit at a height greater than 0.3 m / 1 ft from the ground surface.
PUMP
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
CAUTIONS:
The pump has been evaluated for use with water only.
Risk of electric shock.
Do not remove cord and strain relief. Do not connect conduit to pump.
Do not use the pump in water exceeding 86ºF / 30ºC.
Do not use the pump in flammable liquids.
Do not use the pump for industrial purposes.
Do not use the pump in vehicles or on board ships or aircraft or swimming pools.
Do not use the pump in location where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapor or
gas).
Do not let the pump run dry. Pump must be completely submerged for proper operation and cooling.
Do not lift the pump by its power cord.
Keep the plug dry. Do not expose the plug to water or steam.
Before connecting to the power source, make sure that the pump is assembled and completely submerged in water.
Always disconnect the pump from the power source before performing any maintenance on the pump, lights (if equipped), or fountain.
Do not exceed the voltage shown on the pump.
Check the water level regularly to ensure the pump is completely submerged during operation. The pump should be fully submerged during
operation. Do not add water while operating the product. Always disconnect the pump from the power source before adding water.