Instructions / Assembly

Position first post. For concrete attachment, use
hammer drill with 5/16” masonry bit to drill four
holes 3” deep through each corner of post base.
Clean holes. Use hammer to insert assembled
concrete anchors (provided) until washer is
touching post base. Use 7/16” wrench to tighten
nuts. Ensure post is plumb.
Secure Bottom Frame to two Vertical Frames using
two #10 x 2” screws.
Slide 4’ x 2’ Decorative Screen down into Vertical
Frames and ensure it is fully seated in Bottom
Frame.
Secure one Mid Frame to two Vertical Frames
using two #10 x 2” screws. Slide assembled Mid
Frame and Vertical Frames into slots on posts.
Secure Vertical Frames to posts using four #10 x 1”
self-drilling screws (provided).
Repeat Step 4 for second 4’ x 2’ Decorative Screen.
1
4 5 6
2 3
©2021 Peak Innovations Inc. 2496_ScreenFrame_InstallGuide_ENG_V2
Repeat Steps 5 and 6 for third 4’ x 2’ Decorative
Screen.
Fasten second post in place (see Step 1 for full
details). Install post caps and post base covers.
7 8 9
No representation or warranty is given that your particular application of these products complies with relevant building codes. Therefore consult with
professionals and local building officials before beginning work: (i) to ensure compliance with relevant building codes for your application; (ii) to identify appropriate safety
gear that is to be used during installation such as a safety harness when working above ground; (iii) to ensure that the work area is free from utilities, services and hazards;
and, (iv) to clarify any instructions or warnings that may not be clear. It is the responsibility of the installer to evaluate the conditions and determine the appropriate hardware
and procedure. Failure to do so could result in personal injury, damage to the product, or other damage. Work in a safe manner wearing protective gear such as gloves,
eyewear, headwear, footwear and clothing. When using tools always comply with operation manuals and instructions. Metal and other materials may have sharp edges and
could fragment or splinter during or as a result of handling or cutting. Do not use these products in connection with any substance that is or may be harmful or corrosive to the
products. Inspect and maintain these products on a regular basis.
No member of The Peak Group of Companies (as defined at www.peakproducts.com) shall be liable for any loss or damage resulting from the improper installation or use of
this product. In the unlikely event that any member of The Peak Group of Companies becomes liable for any loss or damage, the aggregate liability shall be limited to the retail
purchase price of the product.
Peak® products and the materials associated therewith are protected by patents, designs, copyright and/or trademarks. All trademarks are used under license from Peak
Innovations Inc. May be subject to patent(s) or patent(s) pending.
Push each screw head into Vertical Frame
channel before driving.
Push each screw head into Vertical Frame
channel before driving.
Once complete frame is secured, Decorative
Screens will be slightly loose to allow for
thermal expansion.
Tools and Materials Needed
Drill
Driver bits
Hammer drill
5/16” Drill bit for concrete
7/16” Wrench
Hammer
Level
Tape measure
6x
Vertical Frame
1x
Post
1x
Post Cap
1x
Post Base Cover
4x
Concrete Anchor
Position Top Frame onto 4’ x 2’ Decorative Screen
and secure using two #10 x 2” screws.
Decorative Screens
Installation Instructions
Screen Frame Post
For 4’ x 2’ Screens
Contents: Contents:
Position second post (do not secure it yet). Slide
assembled Bottom Frame and Vertical Frames into
slots on posts and use wood blocks to level. Ensure
bottom of frame is between 1-1/2” and 2” above
ground. Secure Vertical Frames to posts using four
#10 x 1” self-drilling screws (provided).
1x
Bottom Frame
2x
Mid Frame
1x
Top Frame
12x
#10 x 1”
Self-drilling screw
8x
#10 x 2” Screw