Quick Start Guide CV22 Television Model: CV22
WARNINGS To reduce the risk of electric shock, DO NOT performs any servicing other than what is contained in the operating instructions, unless you are qualified to do so. This symbol is intended to alert the user of the presence of un-insulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
RAIN AND MOISTURE WARNING: To avoid the hazards of fire or electrical shock, DO NOT expose this TV to rain or moisture. INSTALLATION DO NOT block any ventilation openings. DO NOT install near any heat source such as radiators, heat registers, stoves, or other apparatus that produce heat. WET LOCATION The TV SHOULD NOT is exposed to dripping or splashing. Objects filled with liquids, such as vases, SHOULD NOT are placed on the TV. OXYGEN ENVIRONMENT WARNING: DO NOT use in an oxygen tent or an oxygen chamber.
CONTROLS Left Side Panel 1. TV/AV button Selects the video mode. 2. CC button Set the caption function. 3. CH ▲/▼ buttons Selects a program or a menu item. 4. VOL ▲/▼ buttons Adjusts the volume. Adjusts menu settings. 5. POWER button Switches TV set on or off. Front Panel 1. Color TFT screen 2. Speakers 3. Power Indicator Illuminates in red when the TV is off. Illuminates in green when the TV is switched on. 4. Remote Sensor Accepts the IR signal of remote controller.
Rear Panel 1. HDMI Jack Connection for HDMI device. 2. COAXIAL Jack Provides a digital audio output signal for connection to an external digital audio device. 3. 4. 5. 6. 7. 8. COMPONENT IN 9. VGA AUDIO IN Connect the audio cable from the PC to the AUDIO IN of the set. 10. SD Card Slot Firmware upgrading purpose. 11. PILLOW Connect the COMPONENT audio/video output Pillow speaker port. sockets of the DVD to the COMPONENT audio/video Use the switch to select correct voltage.
Wall Mounting With PD168-005? Standard Wall Bracket (Not supplied with TV) 1. Refer to Figure 1. Select a location on the wall approximately 5 inches below the ceiling. NOTE: DO NOT locate AC, Across-Room Wiring, and CATV Signal outlets below the Wall Bracket’s location as it will cause clearance issues and interfere with the TV’s cabinet when mounted to the bracket. Position the Wall Bracket and locate two mounting holes. Secure the bracket to the wall (mounting hardware is not included). 2.
Across Room Wiring A ¼” stereo style pillow speaker (pendant control) jack is located on the TV’s connector panel. This TV is designed to work with either a digital pillow speaker that generates digital-style control codes or a singlebutton analog (switch-style) pillow speaker. A rear panel mounted switch allows use of different brands of pillow speakers and supports Zenith, Philips, and RCA compatible pillow speakers.
Antenna “ANT” Connection An “F” style jack is located on the TV’s connector panel. CAUTION: Some hospital cable systems provide power voltage on the coaxial cable. This TV is NOT designed to be powered via a coaxial cable. DO NOT connect to a powered coaxial cable. Damage will result to the TV. Hospital Coax Cable AC Power A right-angled AC power cord is attached to each TV. Connect the AC power cord to a powered outlet.
Product Accessories (Not Included with TV) 75mm VESA Wall Mount PD168-005 Programming Remote Control PD108-420 Patient Remote Control PD108-427 (*Remote comes with DVD module) Patient Remote Control PD108-421 (*For TV’s without DVD module) ¼” to 6-Pin Jumper Cable PD106-416 ¼” to ¼” Jumper Cable PD106-417 Programming The remote control (PD108-420) is used to perform all setup operations for the TV.
Auto Program The TV automatically scans each available channel for activity. Channels that display activity are memorized into the selected Service Level. 1. 2. 3. 4. 5. 6. 7. 8. 9. After setting Signal, press ▲ or ▼ to highlight Auto Program. Press ► to select it. On Mode, press ◄ or ► to select the scope of channel scanning. Analog Only: TV searches for analog channels only. Digital Only: TV searches for digital channels only.
