J601 User Manual Interface KEY Definition: key Illustrate 1 Power key Long press over 5 seconds to power on and long press to power off 2 WPS key Press to active the WPS 7 USB port Insert USB into LAN port 8 SIM card Slot Insert SIM card 9 SD card Slot Insert SD card 10 Reset The Reset button is on the opposite side of the machine. If you forget Administrator password or Wireless network key, you can press the Reset key to restore factory default settings.
Indicator Color Working Status Green Solid: booting up the device Blink: Turn on-0.
2. Insert the SIM card and SD card. Ensure that the contact area on the card is facing down and that the beveled corner on the card is facing the beveled corner on the holder. 3. Align the battery contacts with the battery compartment connectors, and insert the battery. Replace the back cover lastly. J601 Usage J601 support 4G/3G/2G networks. Insert the SIM card, Wi-Fi devices and the computer can access the Internet through J601, enjoy high-speed network services.
Method Two: Login management page view 1. Computer, open your browser, input http://192.168.1.1 and enter. ●The default Account is ClaroADM ●The default Password is Adm@XXXX (XXXX are the 2.4G Mac’s last 4-digits) Enter the Account and Password, login administration pages 2. Enter the Wi-Fi menu , view the default SSID and Wi-Fi password. The default 2.4G SSID: CLARO_INTERNET_XXX (Where XXX are the last 3 digits of 2.4 MAC Address), and SSID password: CLAROXXXX (Where XXXX are the last 4 digits of 2.
★Recommend that you start using J601 administration pages after setting a convenient landing memorizing SSID and a higher safety factor Wi-Fi passwords Install the driver and connecting the device USB Connection: Windows 7 for example 1. Keep J601 powering on, Plug the device into your computer, it will shows like the following pictures step by step.
2. Double-click the , wait for the installation to complete 3.
Or, Establish Wi-Fi connection: you must ensure that the computer equipped with a wireless network card. If the computer showed the presence of Wi-Fi connectivity, the wireless LAN is available. Otherwise, you need to check your wireless network card is working properly. (The following will be 2.4GWi-Fi as an example) 1. In the Wi-Fi list, select the 2.
2. Enter the correct 2.4G or 5G Wi-Fi password, click Connect.
3.
●Home First part of the main display settings and network status information, such as IPad dress, SIM card status, type and quality of the network signal, whether it is roaming, with or without a new message, and traffic statistics, and system uptime, and so on. Of course, all the menus you see are in Spanish, because the default language is customized.
You can quickly change the Router Gateway step by step, first set the APN, then change the 2.4G SSID and 5G SSID Modify 2.4G SSID and Wi-Fi password and 5G SSID and Wi-Fi password. At last the Device will restart automatically when you click the confirm button.
1. Connection Preferred Cellular Network: Select the Auto Mode, after you turn on J601 without additional operations, the device will automatically connect to the network; select the Manual Mode, you need to manually connect to the network after opening J601 management page. 2. APN Setting You can customize the network configuration or manually add the new APN and set defaulting. 3.
There are four types of networks can be choose: LTE/WCDMA/GSM is Customer customization, and WCDMA/GSM （Auto）, and WCDMA Only is using only 3G,GSM Only is using only 2G. 4. PIN Open your PIN, if you reboot the device, you need to login management page, and the page will prompted to enter the correct PIN code, you can use the SIM card. PIN / PUK code supplied with the SIM card provided by your carrier, please consult your carrier. ●LAN 1.
We can change IP address in this page. 2. DHCP DHCP Mode: Select the server mode, the device can be done using a DHCP server; choose none, which is off the server function. Start / End IP address: Changing DHCP assigned IP and IP segments. Lease Time: Each is assigned a time to use the IP Leased Hosts: J601 each wireless device list and USB device can view the Host name, MAC Address, IP Address, information about the Remaining Time.
●Wi-Fi 1. Basic We can setting the 2.4GWi-Ficonfiguration in this page, like B/G/N mode, Channel, SSID, Wi-Fi KEY and so on. You can also control the opening and closing of 5GWi-Fi, and set up the Wi-Fi Channel .
802.11 A/N/AC Mixed protocol. We set the Channel Width to reach HT20/40/80 Mixed. The highest 5GWIFI rate can reach 867Mbps. 2. WPS You can click the drop-down box and select 2.4G WPS or 5g WPS as the current default, and click the change button to confirm, Then You can use WPS function. J601 supports two kinds of WPS authentication, PBC and PIN. Default is PBC authentication. (The following will be 2.
Using WPS to connecting the J601 (Computer for example): You can press the WPS button on the wireless device or click the PBC button if your wireless network adapter also supports WPS authentication. Waiting for a moment, it will be prompted to connect successfully. Or Select the SSID of the device and manual input Wi-Fi Key and connect it. Then you can see like the following picture.
If the connection is successful within 120 seconds, Then you can see like the following picture. 3.
You can choose wifi-2.4G MAC Filter or 5G MAC Filter, and then the details are as follows: Deny list Stations: If you add the computers or wireless devices MAC address into the list, it can prohibiting the computers or wireless devices connect to the J601.The computes or wireless devices MAC address which are not in the list can able to connect to J601. Allow list Stations: Opposite with Deny list Stations.
1. Firewall You can Disable or Enable the Firewall function. Also you can setting the matching packets rule to receive or reject,Then you can go to the IPV4 Firewall Entries or IPV6 Firewall Entries tab and configure the necessary parameters.
For example: Situation 1: Firewall Enable select Enable Packet Allowed select Drop (blacklist) In the router, the LAN-IP address is 192.168.1.5 to 192.168.1.7 and the 3 network addresses, ICMP protocol, are all filtered. Situation 2: Firewall Enable select Enable Packet Allowed select Accept (whitelist) In the router, except for the three network addresses with the LAN-IP address from 192.168.1.5 to 192.168.1.7, the ICMP protocol can pass, and all other IP addresses are filtered. 2.
3.DMZ Receive all the data from external network interface forwarded to “DMZ IP address” If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer. Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort. DMZ Host: Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication.
2. TR069 The menu shows custom parameters. It is the communication between CPE and ACS.CPE can use this agreement to complete the necessary actions of service opening, function setting, file uploading and downloading, system testing and so on. 3.
Restore the factory settings, all of the personal configuration will be deleted, all configuration pages will be restored to the factory defaults. 5. Firmware Upgrade The page allows you to upgrade the router’s firmware. Remote Sever: You can on the routing connection network，check whether there is a new version, if there is a new version was detected, it can automatically upgrade in the background.
Modify the login password for administrator interface. Also you can set the time to logout the automatically. 6. Date and Time You can synchronize the time with the host, you can also select the time zone 7.
You can change the UI language in this page. 8. Power saving You can change the time of sleep mode or deep sleep mode. In this page you also can disable the Power saving function. Sleep mode: System will enter into the sleep mode, when there is no Wi-Fi client connected to this device. Deep sleep mode: System will enter into deep sleep mode, when there is no Internet access and no Wi-Fi client connected to this device. 9. Reboot You can restart the device.
10.USSD It is a new interactive data service based on GSM network. When you use the phone’s keyboard to type in numbers or symbols that are pre-defined fot the network. You can edid the content on the left, and the results will be returned to the right later. 11.UPNP UPNP means Universal Plug and Play, it is to make all kinds of devices in home network and company network connect with each other seamlessly, and simplify the implementation of related networks. You can check box and activate the function.
Safety Warning Caution:RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
