Installation guide

758 110
125 52
689 lOC I I I I I I -
I I I I I I I I I I_'_ 115 4B
II I I I I I_,'_q I I
I I I I I I I I I I I D 105 41
3 621 _8_£0 I I I I I I Ip_l _4_rlI I I I 95 35
III I I I I I III L
IIIIII ' ' 85 29
I_U"T I L,,4''_
IIIIII FIllJ1"T_e" 75 24
II I I II ILII . . 65 18
mm I I I I I I A_III I_"_lld_., 55 13
_n483 c_70 I I I I I I I
45 7
L,,,_T i i
LU II I I I I '_11 III
mm Z II I I I I I I I L._
I I I I 1_4_" I_t'-I I_"
s
_345
[/1
275 40
30
30 80 90
I I I I I I I
4 10 16 21 27 32
SUCTION LINE TEMPERATURE('C?
Fig, 18_Cooling Charging Chart, PYIPOl@ UnIL_ °°°46
?5S 110
589 100 OUTDOOR TENP
115 46
m _ i i i i i i I I I I I_.,_ 95 33
IIIIII i i i*--i 85 29
_o IIIIII l_l_ ?S 24
,rl i._i 65 18
s IIIIII _l I_I_L_I
_70 I I I I I I I I_'*_"f L_483 _ 55 13
I I I I I I I I I l.s_q 45 7
o _ II I I I I I I J_'q I I
II I I I I I I I Ill.*
z
345 m50
278 40
30
30 50 70 80 90
LINE ('F)
I I I I I I I
4 10 16 21 27 32
758 110
68E 100
Pn
9O
s
< 2
48_ _70
z
t_
tn
_345 50
en
276 40
30
30
I
88_
_621
40 50 60
SUCTION LINE TEMPERATURE
I I I
4 10 15
SUCTION LINE TEMPERATURE
q I
q I.
"1 I
I I
IJfll II I I II
"11 Jfl I III I I II
• 80 90
I.%
I I I
21 27 32
("C?
l_ooli_ i Chart, PYIPO24. Unit._ 00042
75E 110 _"
1O0 OUTDOOR JEcMp
115 46
I I I I I I
I I 95 35
I I I I I I "[.,,_ 85 29
I I I I I I _L,a
I I I I I I "q I
o IIIIII 13
II I I II
illlllll ll-ii -
. N I I -I I _ 55 13
_n 4Be inTO II I IIIIIIIII _ _ _s ?
z41 z
C_
27E 40
30
30 S0 60 80 90
LINE TEMPERATURE . )
I I I I I I I
4 10 16 21 27 32
8UCT[0N LINE TEMPERATURE ('C) SUCTION LINE TEMPERATURE DC)
Fig, 20_Cooling Charging Chart PYIP@3@ Units Fill, 21_--Cooling Charging Chart, PYIP@3@ Unit._°°°4€
c, (_ all lmlts, remove bfowcr assembly fromlmlt. Remove 3crow3seeming 5lower to blower par'titian_:nd31idaassembly out.Be carafttl
not to tear instflatian in blower compartmem,
& gusura proper r-v,asscrnbly by marking blower whecl and motor in rcladan to blower housing bafbro disputably,
c, Lousan sakqc_s) that samwo3whecl to motor 3haft, Rcrnovc sc_'cws that secure motor motmt braekots to housing, and 31ida motor and
motor mount am of housing,
2. gornovc oald clean blower whecl a3 follows:
a, Eusum proper massornbly by marking wheal orientation,
b. Lift wheal from housing. When hmldling and/ur olcaning blower wheal, be sum not to disturb balance weights (dlps) on blowor wheal
VaIlaS,
o, Romovc caked.-an d_t from wheal and housing with a brush, Remora lint and/or dirt acmmaulatlous from whecl oaldhousing with vac_urn
eleanor, using sor_ Nawh _tachmanL Rornova grease and off with mild 3olvant.
d. R¢as_mbla wheal into housing,
c, Rea33ornblc motor into housing. Be sure satsorow3 arc tlghtan¢d on motor shaft fiats and not on round part of shafL
£ gein3_l tmlt acec33 panel.
I2_-