TOUCHLOCK compact stainless steel Ins-177 Date code: 250403
Contents About .................................................................................................................................................. 3 Features ......................................................................................................................................................................... 3 Contents in box .......................................................................................................................................................
About TOUCHLOCK compact stainless steel is a single door, single keypad access control system. The keypad is suitable for internal and external installations. The keypad is suitable for high use applications. The unit is self contained with the control unit, or decision making electronics, housed within the keypad itself. The unit can be powered by both ac and dc 12V power supplies. The output to the electric release is 12Vdc solid state limited to 500mA continuous and 750mA intermittent (7 seconds).
Fitting Using the template provided, mark and drill holes for the cable and the two screws. Enlarge the upper part of the cable hole as shown in the diagram below: • • • • Tap in the wall plugs and screw the top No.8 x 1” posi pan to the wall. Leave the head of the screw about 2mm from the face of the wall. Thread the cable through the wall. Locate the screw into its keyhole on the back of the keypad and slide the keypad down to engage. Remove and adjust as necessary. Tighten down with the bottom No.
Wiring The black wires - Power input The TOUCHLOCK can be powered with 12 - 15 V AC or DC. On DC systems, the wire marked with a white stripe is positive. When using an AC power supply, the polarity is not important. The white wires - Release output The output is 12V DC.
Commissioning Initialising the system After the system has been wired up, be sure to check over the connections against the wiring diagrams provided before powering up for the first time. When the system is powered up for the first time the keypad will bleep 3 times a second. This indicates that the keypad is waiting to be initialised. The red and amber LEDs will be off and the green LED will be flashing.
Operation Programming the keypad The TOUCHLOCK compact SS keypad can be programmed using the master code. To understand each setting, read the following explanations. For more information on how to program each setting, refer to the TOUCHLOCK Programming Guide. Single/multiple code mode By default the keypad will operate in single code mode, only allowing one 4-8 digit code to operate the door. It is possible to change this code as many times as are needed.
TOUCHLOCK programming guide X X X X X X 6 digit programming code Green LED is now Flashing 3 X 8 1 Hold key for 3 seconds X X X 1 Hold key for 3 seconds X 6 Hold key for 3 seconds 1 X X X 2 Single user code 6 Multiple user codes X X X X new 6 digit programming code 2 bell Beep when keys pressed 1 6 Silent unless in menu mode lockout 1 Hold key for 3 seconds door open time Hold key for 3 seconds Remote button 1 Lock wire setting Hold key for 3 seconds 1 Data reset
Applications Standard Installation TOUCHLOCK compact will operate from 12V a.c. or 12V d.c. 12V a.c. 1 ABC 3 BLACK 2 DEF 4 GHI JKL 5 6 7 8 MNO PQR ST 9 WX WHITE UV 12V d.c. 0 YZ Green wires must be insulated white lock wires will drive up to 500mA continuous (750mA for up to 7 seconds) Positive wire is identified by being ribbed or striped. Total load must not exceed PSU capacity. 240V a.c.
Exit button TOUCHLOCK compact will operate from 12V a.c. or 12V d.c. EXIT BUTTON push to make 12V a.c. 1 ABC 3 BLACK 2 DEF 4 GHI JKL 5 6 MNO 7 ST 9 WX GREY PQR 8 UV 0 WHITE 12V d.c. YZ Green wires must be insulated white lock wires will drive up to 500mA continuous (750mA for up to 7 seconds) Positive wire is identified by being ribbed or striped. Total load must not exceed PSU capacity. 240V a.c.
Specification User codes ............................................................................................................................. up to 50 codes 4 to 8 digits Keypad construction ................................................................................................................................. stainless steel Keypad finish .............................................................................................................................................
