User's Manual

ManualsBrandsPaxton Access ManualsElectronicsNet2 PaxLock Â– 72mm Euro lock case

PAGE 1

02/23/2012

Parts list

Tools List

Power Drill

Drill bits

/8",

/8"

Philips screwdriver

Small at blade terminal screwdriver

Pencil

4mm Allen key (supplied)

Technical Support

Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)

1.800.672.7298 supportUS@paxton-access.com

Ins-30168-US Net2 PaxLock

Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/

Net2Air Site Surveyor (690-200-US).

This access control unit uses wireless

communication. It is recommended that a

Net2Air site surveyor is used to determine the

best position for the bridge and control units.

This wireless unit requires a Net2Air bridge

to communicate with the server PC.

Paxton

5 6

1) Front Lock Assembly

2) Rear Lock Assembly

3) Door Handle x 2

4) Mounting screw (1

/4") x 2

5) Mounting screw ( 1

/2") x 2

6) Mounting screw ( 1

/4" ) x 2

7) 8 mm Spindle

8) AA battery x 4

9) 4 mm Allen Key

This unit requires Net2 v4.23 or later software.

Call Technical Support if you require advice.

Summary of content (7 pages)

PAGE 1
02/23/2012 Paxton Ins-30168-US Net2 PaxLock Technical Support 1.800.672.7298 supportUS@paxton-access.com Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST) Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/ This wireless unit requires a Net2Air bridge to communicate with the server PC. Net2Air Site Surveyor (690-200-US). This access control unit uses wireless communication.
PAGE 2
Installing the hardware Step 1 - Marking out 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 Ø 16 Ø 10 105 Paxton 37 75 The lock (not supplied) must first be fitted to the door. Slide the spindle through the lock to allow the template to locate over it. Ensure that the template is square to the door edge by using the top and bottom ruler scales. Mark the 2 x 3/8" and 1 x 5/8" holes.
PAGE 3
Step 5 - Mounting on the door Present the front lock assembly to the door passing the wiring harness through the 5/8" hole. Present the rear lock assembly to the door and join the two parts together with the two mounting screws. Mounting screws are provided in three lengths. Short - Door width 1 1/4" to 1 3/4" Med - Door width 1 1/2" to 2" Long - Door width 1 3/4" to 2 1/4" Step 6 - Wiring Plug the wiring harness into the socket in the rear lock assembly.
PAGE 4
Step 10 - Fitting the handles Fit the two handles and secure with the grub screws provided. Check the mechanical operation of the lock and that the handles operate freely. Software installation The Net2 software should be loaded on the controlling PC with at least one Net2Air bridge installed. Full documentation is supplied with the Net2Air bridge unit and also from the website as follows: XAN1051 - Installing Net2 software < http://paxton.info/1520 > XIns-40084-US Net2Air USB bridge < http://paxton.
PAGE 5
Software configuration Door name: Name the Door. Door open time: Set the door open time. Unlock the Door during: Holds the door unlocked during this timezone. - Set to 'At No Time' for normal user operation. Reader: Local settings for the reader. Output: Configures the lock for timed release or toggle mode. Alarm: Enables/Disables the door alarm functions. (requires contact switch) Events: Shows the events for this control unit only. Access Rights: Lists users who have access through this door.
PAGE 6
Sleep mode The PaxLock is a standalone unit and stays asleep while there is no user activity. The Net2 server cannot wake up the unit. If the PIR is activated or the front button is pressed, it powers up the reader circuits in readiness for a token read. Should nothing occur within 3 seconds, the unit will go back to sleep. If a token is read, then the PaxLock moves into full operation.
PAGE 7
PaxLock reset The PaxLock holds address information for the bridge that it is bound to. This will cause problems if the unit is to be used on another system. The unit requires a hardware reset to clear its bridge information. This is achieved as follows: 1. Remove the inside handle from the door by loosening the securing grub screw. 2. Remove the cover by holding the bottom edge and pulling it towards you. The cover will lift off at the top when the bottom edge is clear of the housing. 3.