User's Manual

ManualsBrandsPaxton Access ManualsElectronicsEasyprox Compact Keypad

11/12/2008

Layout

Parts list

Tools List

Power Drill

Drill bits 10mm, 25mm.

Philips screwdriver

Hacksaw for cutting bolts

Hammer / Mallet

Chisel 25mm

Stanley knife

Adhesive tape

Pencil

Tape measure

8mm spanner (supplied)

2mm Allen key (supplied)



 



  

  







1) Front Lock Assembly

2) Rubber Escutcheon x2

3) Rear Lock Assembly

4) Ins-30067 - Easyprox Template

5) Left and Right Handles

6) Square Drive

7) Strike Plate Backbox

8) Strike Plate

9) Battery Pack

10) Tubular Mortice Latch

11) Latch Screws x4

12) Short Fixing Screws x4

13) Long Fixing Screws x4

This unit is for Indoor use only.

Technical Support

Technical help is available: Monday - Friday from 5am - 5pm PST / 8am - 8pm EST

1 800 672 PAXT support@paxton.co.uk

Ins-30100-US Easyprox compact keypad

Documentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/

NOTE: All dimensions are shown in millimetres to maintain accuracy.

Summary of content (8 pages)

PAGE 1
1/12/2008 Ins-30100-US Easyprox compact keypad Technical Support 1 800 672 PAXT Technical help is available: support@paxton.co.uk Monday - Friday from 5am - 5pm PST / 8am - 8pm EST Documentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/ Layout This unit is for Indoor use only.
PAGE 2
Fitting the latch Step 1 Decide on the height of the latch and mark a line on the edge of the door and about 80mm across both faces. Fold the template along one of the dotted lines (right or left). Tape it to the door, the latch centre line positioned on the height mark. (Diagram A). 80m m 57mm 25mm mm 25 3.5mm Diagram A - Drilling template taped to door Diagram B - Latch dimensions Mark the 4 x 10mm holes and 1 x 25mm holes.
PAGE 3
Step 10 Fit the battery pack into the unit. Replace the access plate and secure with the standoff screws. Step 11 Fit the rubber escutcheons to front plate and the back plate. Present the front and rear lock assembly to the door, locating the square drive in its recess and secure the two parts of the lock together with the fixing screws. Fit the two handles positioning the screw holes to the underside and secure with the grub screws provided.
PAGE 4
INITIALISING A NEW SYSTEM Choose a 6 digit Programming Code and load this into the unit as follows: 6 digit Programming Code 6 digit Programming Code The factory User Code is now set to 1234 IMPORTANT NOTE: Do not set the Programming Code to 123456 The programming code must not contain the same string of digits as the user code. The default user code is 1234 - therefore the programming code must not be set to 123456 You can now set up the user codes and features using the programming chart.
PAGE 5
PROXIMITY with TOUCHLOCK mode (i) The unit must first be initialised in TOUCHLOCK mode: See TOUCHLOCK section IMPORTANT NOTE: Do not set the Programming Code to 123456 (ii) Before enrolling a card pack, set up the required operating mode, as follows: Enter 6 digit Programming Code 1 1 Card plus PIN Hold for 3 secs 2 OR Card plus code 3 OR Card or Code (iii) Now present enrolment card All tokens will now be validated.
PAGE 6
Normal Operation - LED Indications The external handle is free to move and is only engaged once access has been granted. The inside handle is always engaged. When access has been granted, the unit will flash the Green LED and the handle will then engage. The unit will beep during this time to advise the user that access has been permitted. This default time (4 seconds) can be changed with the ‘door open time’ card. Presenting an invalid or barred card will flash the Red LED and sound a low tone.
PAGE 7
Door open time 1. 2. 3. 4. Take the door open time function card from the starter pack. Present the card to the reader. The reader will start beeping. Wait for the required period you wish the door to remain open. Present the card again at the end of the period to set the open time. The beeping will stop. Silent operation card 1. 2. 3. 4. Take the silent operation function card from the starter pack Present the card to the reader.
PAGE 8
Battery replacement 1. Remove the unit from the door by removing the 4 securing screws on the rear lock assembly. (see Layout on front page) 2. Remove the top two standoff screws - Fig 1 3. Remove the access plate to reveal the battery pack. - Fig 2 4. Unplug the lead and replace the pack with a new Paxton Access battery pack. - Fig 3. (NOTE: The unit will retain its settings and should not be manually reset) 5. Refit the access plate and secure. 6.