User's Manual

ManualsBrandsPaxton Access ManualsElectronicsEasyprox nano

Page 1

09/07/2009

Parts list

Tools List

Power Drill

Drill bits 3/8”, 1”.

Philips screwdriver

Hacksaw for cutting bolts

Hammer / Mallet

Chisel 1 inch

Stanley knife

Adhesive tape

Pencil

Tape measure

8mm spanner (supplied)

2mm Allen key (supplied)

1) Front Lock Assembly

2) Rear Lock Assembly

3) Rubber Escutcheon x2

4) Left and Right Handles

5) Battery Pack

6) Tubular Mortice Lock

7) Square Drive Bar

8) 8 mm Conversion Sleeve

9) 2 mm Allen Key

10) 8 mm Spanner

11) Strike Plate Backbox

12) Strike Plate

13) Long Mounting Screws x4

14) Short Mounting Screws x4

This unit is for Indoor use only.

Technical Support

Technical help is available: Monday - Friday from 12:00 AM - 5:00 PM (PST)

Saturday from 1:00 AM - 5:00 AM (PST)

1.800.672.PAXT support@paxton-access.com

Ins-30107-US Easyprox nano

Documentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/

This access control unit uses wireless communication.

It is recommended that a Net2Air site surveyor is used to

determine the best position for the Net2Air bridge and Nano

control units.

This unit requires a Net2Air bridge (USB or Ethernet) to

communicate with the controlling PC running Net2 v4.14 or

later software.

 ONLY

Paxton Access

4HIS BATTERY PACK IS TO BE REPLACED

WITH 0AXTON !CCESS PART NUMBER





 

 

  











Paxton Access

4HISBATTERYPACKISTOBE

REPLACEDWITH0AXTON!CCESS

PARTNUMBER 746-003ONLY

6

4HISBATTERYPACKISTOBE

REPLACEDWITH0AXTON!CCESS

PARTNUMBER ***-*** ONLY

6

Paxton Access

Summary of content (8 pages)

PAGE 1
09/07/2009 Ins-30107-US Easyprox nano Paxton Access Technical Support 1.800.672.PAXT support@paxton-access.com Technical help is available: Monday - Friday from 12:00 AM - 5:00 PM (PST) Saturday from 1:00 AM - 5:00 AM (PST) Documentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/ This unit requires a Net2Air bridge (USB or Ethernet) to communicate with the controlling PC running Net2 v4.14 or later software.
PAGE 2
Installing the hardware Step 1 - Marking out Decide on the lock height and mark this on the door. Fold the template along one dotted line and tape it to the door with the ‘Centreline of Latch’ at the required height. Mark the 4 x 3/8”and 1 x 1” holes. Remove the template, fold along the other dotted line and apply it to the other side of the door at the same height. Mark the holes as before. Step 2 - Drilling Drill a 1” hole in the door edge at least 3” deep to accept the latch.
PAGE 3
Step 5 - Mounting on the door Select the short (doors thinner than 1 3/4”) or long mounting screws and cut to length if required. (door thickness + 3/16”) Fit the rubber escutcheons to the front and back plates. Present the front and rear lock assembly to the door, locating the square drive in its recess and join the two parts together with 4 mounting screws. Step 6 - Fitting the handles Fit the two handles, positioning the screw holes to the underside and secure with the grub screws provided.
PAGE 4
Software installation The Net2 software should be loaded on the controlling PC and at least one Net2Air bridge configured to communicate with the Net2 nano unit. Full documentation is supplied with the Net2Air bridge unit and also from the website as follows: XAN1051 - Installing Net2 software < http://paxton.info/1520 > XIns-30084-US Net2Air USB bridge < http://paxton.info/1453 > XIns-30085-US Net2Air Ethernet bridge < http://paxton.
PAGE 5
Software configuration Door name: Name the ACU. Door open time: Set the door open time. Unlock the Door during: Permanently unlocks the door while this time zone is active. - Should be set to ‘At No Time’ for normal user operation. Reader: Local settings for the reader. Output: Configures the lock for timed release or toggle mode. Events: Shows the events for this control unit only. Access Rights: Lists users who have access through this door. Name: Each reader can be named individually if required.
PAGE 6
Net2Air wireless communication The access control unit connects to the Net2 software running on the PC using Paxton Access’ Net2Air proprietary wireless technology. A Net2Air bridge enables communication from the Net2 software to the Paxton Access nano family of products. Radio signals do not always behave as you might expect. For example, a mobile phone that displays a full signal on one part of the site will lose signal completely only a few feet away.
PAGE 7
Low battery warning When the battery voltage falls below 4V, the user will see a delay between the card being read and access being granted. This delay provides a warning that the battery pack should be replaced. The warning delay starts at 5 seconds, increasing up to 25 seconds as the battery discharges with use. Battery replacement 1. Remove the unit from the door by removing the 4 securing screws on the rear lock assembly. 2. Remove the top two standoff screws - Fig 1. 3.
PAGE 8
Specifications Features Min Number of Cards 250 Access Levels 64 Time Zones Maximum door open time Max 10,000 1 sec 99,999 sec 10 ACU’s per Net2Air bridge - Recommended 100 Net2Air bridge (data lines) per system Net2Air wireless range to ACU 20 yds Events stored in ACU with no server connection 4,096 Read Range Environment Operating temperature - Battery limits Token Keyfob 2 inch 1 inch Min Max 0 °C (-32 °F) +55 °C (+131 °F) No Waterproof Low Vandal resistance Paxton Battery Pa