User's Manual

Wiring
2EDVDC
"ROWN
/RANGE
'REEN
9ELLOW
"LUE
-AUVE
"LACK7HITE
"ROWN
9ELLOW
2EADER
/RANGE
+EYPAD
V
V
.#
./
#OM
.#
./
#OM
!LARM/UTPUT
V
#ONTACT
V
%XIT
V
4AMPER
035
2X
4X
2ELAY
2ELAY
%XIT
#ONTACT
4AMPER
035
/+
V
V
2ED
"ROWN
/RANGE
'REEN
9ELLOW
"LUE
-AUVE
"LACK7HITE
"ROWN
9ELLOW
/RANGE
2EADER
+EYPAD
0OWER
2ELAY2ELAY)NPUTS
.ETWORK
#!4CABLECODING
7HITE'REEN
'REEN
7HITE/RANGE
/RANGE




3CREENORSPARECORES
FROMNETWORKCABLE
#!54)/.FORVDCREADERSONLY&OR CORRECTCONNECTIONOFOLDVREADERSREFERTO INSTRUCTIONS
Serial number 241821 Test ID: 012345678901 z-1440
           
6
2ED,%$
!MBER,%$
'REEN,%$
$ATA$
#LOCK$
-EDIADETECT
%NTRY
6
2EADER
%NTRYCONFIRM
6
2ED,%$
!MBER,%$
'REEN,%$
$ATA$
#LOCK$
-EDIADETECT
%NTRY
6
.ET#ONTROL5NIT
6 %XIT%NTRY 'REEN,%$ 6
.ET!IR)NTERFACE
2ED6
"ROWN
/RANGE
'REEN
9ELLOW
"LUE
-AUVE
%XIT
#ONTACT
"LACK
#ARDREADERORKEYPAD
V
V
.#
./
#OM
"ELL
0OWER$OORRELAY
!LARM
witch
2
S
#ONTROL
UNIT
)NPUTS
CAUTION&OR6DCREADERSONLY
&ORCORRECTCONNECTIONOFOLDREADERS
REFERTOINSTRUCTIONS
6
2ED,%$
!MBER,%$
'REEN,%$
$ATA$
#LOCK$
-EDIADETECT
%NTRY
6
2EADER
%NTRYCONFIRM
6
2ED,%$
!MBER,%$
'REEN,%$
$ATA$
#LOCK$
-EDIADETECT
%NTRY
6
.ET#ONTROL5NIT
6 %XIT%NTRY 'REEN,%$ 6
.ET!IR)NTERFACE
Entry conrmation button
(optional)
Input terminal (FOR
FUTURE USE)
Paxton Access Net2 control unit
Readers used with Net2Air can be extended using Beldon CR9540 10-core overall screened cable. The maximum
cable length between the reader and its Net2 ACU or Switch 2 is 100 yards
Cable extensions
Using an entry conrmation button
Where two doors are close together and there is a possibility that both may pick up the Net2Air token, a push to
make button can be used to conrm an entry request for a specic door. Where tted, the button must be pressed
within 5 seconds of a valid Net2Air token being recognised to unlock the door.
Conguration
Firmware download
When rst powered up new rmware will be downloaded from the interface to the reader.
This is indicted by ashing amber and red LEDs on the reader. Once complete all LEDs will be lit.
This may take up to 10 minutes to complete. Do NOT disconnect power during the rmware update.
If the rmware update is still taking place after 10 minutes then remove and then re-connect the ACU cable. Listen
to the reader, the reader should NOT beep. If the reader beeps within approximately 10 seconds of power up it will
not take the rmware update. Repeat the process until the reader does NOT ‘beep’ on power up. Then leave for 10
mins to allow the update to take place
To enable the use of an entry conrmation button do the following steps:
1. Power down the Net2Air interface board
2. Power up the Net2Air interface board
3. Press and hold the entry conrmation button for a minumum of 3 seconds within 60 seconds of power up.
To disable the use of the button repeat the above process.
*
*
Paxton Access Switch2 control unit
*