User Guide

Quick Setup Guide
PAX TECHNOLOGY INC.
PAX E600
Integrated Smart Terminal
Note: Product images shown may be different than actual
product received.
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
Magnetic stripe card: Place the magnetic stripe face down. Keep
the magnetic stripe card perpendicular to the main display. Swipe
card through the magnetic card slot at a constant speed.
IC card: Place the IC chip face up. Insert the IC card into the card
slot and push it to the end.Contactless card: Put the contactless
card on the center of the payment module screen.
L-Sensor (Ambient Light Sensor): Automatically adjusts backlight
brightness of main display
Wireless Communication: Wi-Fi, Bluetooth ® wireless
technology, 3G/4G
Positioning: Supports GPS, BeiDou, Compass, GIONASS
Card Slots: SIM card slot, Micro SD card slot (supports up
to
128GB),Magnetic stripe card/IC card slot, using
two-in-one(supports MAG&ICC)
Magnetic Card Reader: Supports Track 1/2/3
IC Card Reader: Conforms to ISO7816 standard, EMV2000
L1 & L2,PBOC3.0
Card Readers
9
SIM Cards
To insert SIM card, open battery cover, remove battery, and insert
SIM card into slot in direction shown on label.
To remove SIM card, first push it further into slot. (The card will then
stick out of the slot a little.) Next, push card again to remove.
10
SD Card
To insert SD card, open battery cover, remove battery, and insert
card into slot in direction shown on label.
To remove SD card, open battery cover, remove battery, and remove
the SD card from slot.
Specifications
Device Location
Locate the device on a counter top, desktop or table top. Keep the
device away from direct sunlight, excessive dust, moisture, and
heat. Avoid locating the device near electrical devices that might
introduce interference such as microwave ovens and blow dryers.
Cleaning the Device
WARNING:
Do not use industrial strength or abrasive cleaner as it may damage
or scratch the screen.
• Do not immerse tablet in water (or liquid).
• Do not spray water or cleaner into card reader or ports.
• To clean screen, apply distilled water or mild glass cleaner onto a
soft, lint-free cloth and gently wipe screen.
• To clean device, apply distilled water or plastic-safe cleaner onto
a soft, lint-free cloth and wipe gently.
14
Installation and Usage Tips
• Avoid exposing the device to an excessively hot, humid, dusty, or
strong electromagnetic environment.
• Do not vibrate, shake, or drop the device.
• Do not plug or unplug any part of the device while it is powered
on. This may cause damage to an internal circuit.
• There is a risk of explosion if the battery is replaced with an
incorrect type.
• Please contact PAX technical support for assistance with the
device.
C
aution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment. In a domestic environment, this product
may cause radio interference in which case the user may be
required to take adequate measures.
SIM
SD
Working Environment:
R.H.: 10% ~ 93% (non-condensing)
Storage Environment:
R.H.: 5% ~ 95% (non-condensing)
Temperature: 0℃～50℃(32℉～122℉)
Temperature:-20℃～70℃(-4℉～158℉)
11
12
13
Printer Paper
To install the paper:
1. Press printer cover button (see page 2 for location) and open
cover.
2. Insert paper roll with end facing up and extending out of E600.
3. Gently snap printer cover closed.
To tear the paper, press the paper downward along the cutter and
pull it to the left or right along the cutting edge.
To reinstall battery cover:
Properly align battery cover and press it to secure.
7
PAX TECHNOLOGY INC.
Contactless Card Reader: Compatible with ISO14443 Type A&B
Rechargeable Lithium-ion Battery: 7.2V/2600mAh
Power Supply: 100-240VAC,50Hz/60Hz(input)
9V/2.5A(output)
Printer:
2-inch thermal printer with auto-cutter, supports
58x50mm paper roll
Audio:
Built-in speaker, supports headphone output
Camera:
Front camera: 5-megapixel, fixed-focus, high-speed
code scanning
Rear camera: 30W-pixel, fixed-focus, high-speed
code scanning
Battery cover
6
The snap-in fit battery cover is in underside of E600, the cover is
intended only for occasional use by operators, such as for the
installation of SIM and SD card. Correct removal and reinstallation
is permitted under the following instructions:
To remove battery cover:
Hold the sides of E600, and push further the button in direction
shown below to open battery cover.
12
7
8
9
10
11
Operating System: Android 7.1
CPU: Cortex A53 Quad-core, 1.4GHz
Memory:
1GB RAM + 8GB Flash Memory
Display:
8-inch, resolution: 800x1280, multi-touch capacitive
touch screen