User's Manual

S80S80
S80
Handover
Countertop Payment Terminal
Installation Manual
PAX TECHNOLOGY LIMITED
Specification
Specification
5
1) Use a power bar well grounded and with a fuse in it.
2) Protect power supply cable and power adaptor. If they are
broken, they are no longer be used.
3) Before connect power bar to AC socket, make sure the
voltage is correct as POS states.
4) POS should be placed steady on table. It is not allowed
make it under sun beam, high temperature, high humidity or
place full of dust.
5) Keep it away from liquid.
6) Don't insert hard stuff into port which may damage POS
severely.
7) When a POS is in failure, please contact designated
personnel to maintain it. It is not allowed to repair it on your
own.
8) When insert paper roll, do not touch paper cut and protect
your finger from being hurt.
9) Only use designated paper roll to avoid paper jam or
damaging the printer.
Notice at Installation and Use
4
Notice at Installation and Use
Default
CPU: 32-bit ,ARM9
Memory: 8MB Flash, 16MB SDRAM
Display: 128 x 64 pixel LCD, LED backlight
Keypad: 10 alphanumeric keys, 8 functional keys,
4 ATM keys, 1 switch(on) key
ISO7812, Track 1/2/3,
bi-directional swipe
IC Card Reader: 1, EMV2000 compliant
SAM Slots: 3, ISO7816
Modem: Sync. (
)
Async. (V.92, )
Peripheral Ports: 1 RS232, 1 PIN Pad, 1 line port,
1 Phone port
Printer: Thermal printer, Speed: 20 lines/sec,
Paper width: 57mm
Paper roll outer diameter: 50mm
Power Supply: Input 100-240VAC, 50Hz/60Hz, 1.5A
Output 8.2VDC, 5A
Working Environment: Temperature:0 40 (
R.H. :10% 90%(non-condense)
Storage Environment: Temperature:-20 70 (
R.H. :5% 95% non-condense
Dimensions: 216mm x 95mm x 86mm (L x W x H,
including the keypad privacy shield)
Weight 525g
Optional:
Built-in Ethernet module
HDLC up to 9600bps,
V.21,V.22/V.22bis,V.29
up to 56Kbps
, 1 USB port
32 104 )
-4 150 )
Built-in GPRS module
Mass storage: 128MB
Contactless Card Reader (Can connect with an external
contactless card reader as an integrated
design of POS system. ISO/IEC14443
Type A/B, 4 LEDs RF Indicator)
PIN Protection
PIN Protection
The following techniques can be employed to provide for
effective screening of the PIN-entry during the PIN entry
process. These methods would typically be used in combination,
though in some cases a method might be used singly.
Positioning of terminal on the check-stand in such way as to
make visual observation of the PIN-entry process infeasible.
Examples include:
Installing PED on an adjustable stand that allows consumers to
process difficult.
Positioning of in-store security cameras such that the PIN-entry
keypad is not visible.
Post instructions around check-stand, in order to inform
customers. Instructing the cardholder regarding safe PIN-entry.
When the cardholder input his/her PIN, he/she had better use
his/her body and hands to prevent visual observation of PIN-
entry process.
-Visual shields designed into the check-stand. The shields
may be solely for shielding purposes, or may be part of
the general check-stand design, e.g., used as selling
area.
-Position the PED so that it is angled in such a way to
make PIN spying difficult.
Note *Customer instruction methods are less repeatable and
therefore should be used in combination with other methods.
Security levels: L = low M = medium H = high
S80 PIN-entry observation corridors v.s. PIN protection methods
Customers
in Queue
Cashier
Customers
Elsewhere
On-Site
Camera
Remote
Cameras
Observation Corridors
Method
S80 on
Adjustable Stand
Post Customer
Instruction
S80 in Check-Stand
with shield
swivel the terminal sideways and/or tilt it forwards/backwards to
a position that makes visual observation of the PIN-entry
® ®
®
Note To protect the process of PIN-entry, it is not limited to the
above methods and examples, merchants also can adopt other
methods and steps to keep cardholder's PIN safe.
Magnetic Card Reader:
CAUTION To reduce the risk of fire, use only No.26 AWG
or larger telecommunication line cord