USER MANUAL MODEL 2110 CopperLink Ethernet Booster This is a Class A device and is intended for use in a light industrial (commercial) environment. It is not intended nor approved for use in a heavy industrial or residential environment. Part# 07M2110-UM Rev.
CONTENTS 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Warranty Information ................................................................. Compliance................................................................................... EMC Compliance:......................................................................... Safety Compliance: ...................................................................... PSTN Compliance: .......................................................................
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 2110 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of the shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not performs as warranted, your sole recourse shall be repair or replacement as described above.
1.2 RADIO AND TV INTERFERENCE (FCC PART 15) This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause interference to radio and television reception.
1.5 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container. This number may be obtained from Patton Electronics Technical Services at: • Tel: +1 (301) 975-1007 • Email: support@patton.com • URL: http://www.patton.com Note Packages received without an RMA number will not be accepted. 1.
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007. 2.
Figure 1. Typical application When using a Model 2110, in conjunction with a PoE Switch, the user extends the 802.3af PoE and 10/100 Ethernet an additional 100 meters (328ft). POE-enabled IP Cameras can be placed 200 feet away from the Ethernet switch and can be powered up via PoE by the 2110. (See Appendix A.6 on page 11 for power and distance specifications). 3.
2110 Model Types: 2110/P - PoE/Ethernet 2110/PSE - PoE/Ethernet 2110/EUI - Ethernet only A S U nd yla ar ,M O E o P A S S S A N . L Y C .
The 2110/P, 2110/PSE/EUI-48, and 2110/PSE/EUI inject power on the data pair pins 1/ 2 (POE+) and 3/ 6 (POE-) of the connector labeled “PoE OUT.” The 2110/P accepts POE power on either pin pairs 1/ 2 and 3/ 4, or 4/ 5 and 7/ 8 on the connector labeled “PoE IN.” Note The POE power on the 2110/P is rectified and thus polarity of the power is irrelevant. 3.
4.2 LED STATUS MONITORS The Model 2110 features two top panel LEDs that monitor PoE output and Ethernet activity, and two bottom panel LEDs that monitor power input and Ethernet activity. Figure shows the locations of each LED. Table 1 describes the LED functions. Table 1: LED descriptions Description LED PoE Link* PoE OUT (Top Panel) Link/Act Ethernet IN Power* (Bottom Panel) Link/Act Indicates link with down-stream PoE device. (Not present on 2110/EUI) Indicates link and activity on output port.
APPENDIX A SPECIFICATIONS A.1 ETHERNET CONNECTION • Two Ethernet ports 10/100BaseTX; 802.3af • Auto-Negotiating 10/100 • Supports Flow Control (IEEE803.X) for full duplex operation • Supports back pressure for half duplex operation • Store and forward • Auto MDI-X • 802.3af pass through A.2 LED STATUS INDICATORS • PoE/Power (Green): Glows solid when there is power to the unit • Ethernet (Green): Flashes when passing traffic Note See Table 1 on page 10 for LED details. A.
APPENDIX B MODEL 2110 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES Description Patton Model # Base Models 2110/P 2110/PSE/EUI-48 2110/EUI 07M2110-UM 10/100 Ethernet Booster; 802.3af; 0-50°C 10/100 Ethernet Booster/PoE Injector; 802.3af; 0-50ºC, 48VDC 10/100 Ethernet Booster; External 100-240VAC; 0-50°C User Manual Power Supplies 08055-2110-I 10/100 Ethernet Injector; External 100-240VAC; 0-50°C 080511-06 080511-07M 12V Adapter, 1.25A 48V Adapter, 0.
