CopperLink™ Model 1211E/1212E Industrial High Speed Ethernet Extender User Manual This is a Class A device and is not intended for use in a residential environment. Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com Part Number: 07MCL1212E-UM, Rev.
Patton Electronics Company, Inc. 7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel: +1 (301) 975-1000 Fax: +1 (301) 869-9293 Support: +1 (301) 975-1007 Web: www.patton.com E-mail: support@patton.com Trademark Statement The term CopperLink is a trademark of Patton Electronics Company. All other trademarks presented in this document are the property of their respective owners. Copyright © 2014, Patton Electronics Company. All rights reserved.
Summary Table of Contents 1 General information .......................................................................................................................................... 12 2 Installation ........................................................................................................................................................ 15 3 Configuration .......................................................................................................................................
Table of Contents Summary Table of Contents ...................................................................................................................................3 Table of Contents ...................................................................................................................................................4 List of Figures ........................................................................................................................................................
CopperLink 1211E/1212E User Manual Radio and TV Interference (FCC Part 15) ............................................................................................................30 CE Declaration of Conformity ..............................................................................................................................30 Authorized European Representative .....................................................................................................................30 Service ....
List of Figures 1 2 3 4 5 6 7 8 9 10 11 Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 CL1211E/CL1212E rear panel options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 CL1212E (RJ-45) twisted pair line interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Tables 1 2 3 4 5 6 7 S1 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Local/Remote Unit Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Symmetric/Asymmetric Selection Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CopperLink 1211E/1212E User Manual About This Guide About This Guide This guide describes the CopperLink Model 1211E/1212E hardware, installation, and basic configuration.
CopperLink 1211E/1212E User Manual CAUTION CAUTION WARNING WARNING About This Guide The alert symbol and CAUTION heading indicate a potential hazard. Strictly follow the instructions to avoid property damage. The shock hazard symbol and CAUTION heading indicate a potential electric shock hazard. Strictly follow the instructions to avoid property damage caused by electric shock. The alert symbol and WARNING heading indicate a potential safety hazard.
CopperLink 1211E/1212E User Manual About This Guide Safety When Working With Electricity • This device contains no user serviceable parts. This WARNING device can only be repaired by qualified service personnel. • Do not open the device when the power cord is connected. For systems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected.
CopperLink 1211E/1212E User Manual About This Guide This device contains no user serviceable parts. This device can only be repaired by qualified service personnel. WARNING WARNING CAUTION This device is NOT intended nor approved for connection to the PSTN. It is intended only for connection to customer premise equipment. Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry.
Chapter 1 General information Chapter contents Overview ...............................................................................................................................................................13 Features .................................................................................................................................................................13 Description............................................................................................................
CopperLink 1211E/1212E User Manual 1 • General information Overview Thank you for purchasing this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +(301) 975-1007.
CopperLink 1211E/1212E User Manual 1 • General information Figure 1. Typical applications The pair of CL1212E models work together to create a transparent extension between two peered Ethernet LANs using twisted pair (2-wire) or Cat5+. Figure 1 shows typical applications.
Chapter 2 Installation Chapter contents Planning the Installation........................................................................................................................................16 Connecting the Line Interface ...............................................................................................................................17 Connecting the Line Interface for CL1212 .....................................................................................................
CopperLink 1211E/1212E User Manual 2 • Installation Planning the Installation CAUTION The Interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability. To install the CL1212E Ethernet Extender, do the following: 1.
CopperLink 1211E/1212E User Manual 2 • Installation Connecting the Line Interface The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability. CAUTION The CL1212E supports communication between two peer Ethernet LAN sites over a distance of up to 10,000 ft (3 km) over 24 AWG (0.5 mm) twisted-pair wire, Cat5+.
2 • Installation 1 CopperLink 1211E/1212E User Manual RING TIP Figure 4. CL1212E (Terminal Block) twisted pair line interface Connecting the 10/100Base-T Ethernet Interface CAUTION The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability. The RJ-45 ports labeled Eth 0 and Eth 1 are Auto-MDIX 10/100Base-T interfaces.
CopperLink 1211E/1212E User Manual 2 • Installation Connecting Power CAUTION The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability. The CL1212E does not have a power switch, so it powers up as soon as it is plugged in. An external AC or DC power supply is available separately.
Chapter 3 Configuration Chapter contents Introduction ..........................................................................................................................................................21 Accessing the DIP Switches ...................................................................................................................................21 Configuring DIP Switch S1.................................................................................................................
CopperLink 1211E/1212E User Manual 3 • Configuration Introduction The CL1212E has eight DIP switches (S1) for configuring the unit for a wide variety of applications. This section describes switch locations and explains the different configurations. Accessing the DIP Switches 1. Using a small flat-tip screwdriver, remove the protective cover located on the underside of the CL1212E (see figure 6). Figure 6. Removing protective cover 2.
CopperLink 1211E/1212E User Manual 3 • Configuration Configuring DIP Switch S1 DIP switch S1 is where you configure the Line interface. The following tables describe the configuration for the CL1212E. Table 1.
CopperLink 1211E/1212E User Manual 3 • Configuration Switch S1-5: General Protection (Signal to Noise Ratio) Use switch S1-5 to configure line noise protection. Table 4.
Chapter 4 Operation Chapter contents Introduction ..........................................................................................................................................................25 Front Panel LED Status Monitors .........................................................................................................................
CopperLink 1211E/1212E User Manual 4 • Operation Introduction Once the CL1212Es are properly installed, they should operate transparently. No user settings required. This section describes reading the LED status monitors. Before applying power to the CL1212E, please review “Connecting Power” on page 19 to verify that the unit is connected to the appropriate power source.
Chapter 5 Contacting Patton for assistance Chapter contents Introduction ..........................................................................................................................................................27 Contact information..............................................................................................................................................27 Warranty Service and Returned Merchandise Authorizations (RMAs).....................................................
CopperLink 1211E/1212E User Manual 5 • Contacting Patton for assistance Introduction This chapter contains the following information: • “Contact information”—describes how to contact Patton technical support for assistance. • “Warranty Service and Returned Merchandise Authorizations (RMAs)”—contains information about the warranty and obtaining a return merchandise authorization (RMA). Contact information Patton Electronics offers a wide array of free technical services.
CopperLink 1211E/1212E User Manual 5 • Contacting Patton for assistance RMA Numbers RMA numbers are required for all product returns. You can obtain an RMA by doing one of the following: • Completing a request on the RMA Request page in the Support section at www.patton.com • By calling +1 (301) 975-1007 and speaking to a Technical Support Engineer • By sending an e-mail to returns@patton.com All returned units must have the RMA number clearly visible on the outside of the shipping container.
Appendix A Compliance Information Chapter contents Regulatory Information .........................................................................................................................................30 EMC Directive: ..............................................................................................................................................30 Low-Voltage Directive (Safety): ..........................................................................................................
CopperLink 1211E/1212E User Manual A • Compliance Information Regulatory Information EMC Directive: • FCC Part 15, Class A • EN55022, Class A • EN55024 • EN50581 Low-Voltage Directive (Safety): • IEC/EN60950-1, 2nd Edition • UL60950-1/CSA C22.2 No.
CopperLink 1211E/1212E User Manual A • Compliance Information Service All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container. This number may be obtained from Patton Electronics Technical Services at: • Tel: +1 (301) 975-1007 • Email: support@patton.com • URL: http://www.patton.com Packages received without an RMA number will not be accepted.
Appendix B Specifications Chapter contents Line Connector .....................................................................................................................................................33 LAN Connectors ...................................................................................................................................................33 Transmission Line .......................................................................................................................
CopperLink 1211E/1212E User Manual B • Specifications Line Connector • RJ-45 or Terminal Block LAN Connectors • CL1212E: 2 RJ-45, 10/100Base-T, IEEE 802.3 Ethernet • CL1211E: 1 RJ-45, 10/100 Base-T, 1EEE 802.
Appendix C Factory Replacement Parts and Accessories Chapter contents CL1211E/CL1212E Factory Replacement Parts and Accessories...........................................................................
CopperLink 1211E/1212E User Manual C • Factory Replacement Parts and Accessories CL1211E/CL1212E Factory Replacement Parts and Accessories Patton Model # Description Base Models 07MCL1212E-UM User Manual Power Supplies PS-03671H1-004 100–240 VAC (5 V, DC/3 A) Wall mount power adapter 12V- PSM 12 VDC Input Adapter 24V-PSM 24 VDC Input Adapter 48V-PSM 48 VDC Input Adapter Power Plugs for Universal Input AC Power Supply 12-130 European replacement plug 12-129 American replacement plug 12-131
Appendix D Interface Pin Assignment Chapter contents 10/100Base-T Interface .........................................................................................................................................37 RJ-45 ..............................................................................................................................................................37 Line Interface ..................................................................................................................
CopperLink 1211E/1212E User Manual D • Interface Pin Assignment 10/100Base-T Interface RJ-45 1 TX+/RX+ 1 2 3 4 5 6 7 8 2 TX-/RX3 RX+/TX+ 4 (no connection) 5 (no connection) 6 RX-/TX7 (no connection) 8 (no connection) Figure 9. CL1212E 10/100Base-T RJ-45 Connector Pin-out. Line Interface RJ-45 1 (no connection) 1 2 3 4 5 6 7 8 2 (no connection) 3 (no connection) 4 (RING) 5 (TIP) 6 (no connection) 7 (no connection) 8 (no connection) Figure 10.
Appendix E Line Rate & Reach Chart Chapter contents Line Rate & Reach Chart Based on 24 AWG (0.5 mm) ........................................................................................
CopperLink 1211E/1212E User Manual E • Line Rate & Reach Chart Line Rate & Reach Chart Based on 24 AWG (0.5 mm) Table 6. Line Rate & Reach Chart Using Twisted-Pair (Long Range) Distance in Feet Mode (Long Range) Asymmetric S1-2 ON S1-3 ON ft Mbps m/km DS US 250 ft 76 m 67 16 1000 ft 305 m 59 16 2,000 ft 610 m 45 11 3,000 ft 914 m 31 5 5,000 ft 1.
