For For Quick Quick Start Start Installation Installation SmartNode 4830 Series Analog VoIP Integrated Access Device Quick Start Guide Approval Models that are equipped with telecom interfaces have been approved for connection to the public telecommunication network as listed under PSTN regulatory compliance. Important This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial or residential environment.
Patton Electronics Company, Inc. 7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel: +1 (301) 975-1000 Fax: +1 (301) 869-9293 Support: +1 (301) 975-1007 Web: www.patton.com E-mail: support@patton.com Trademark Statement Patton, the Patton logo, and SmartNode are registered trademarks of Patton Electronics Company. The terms SmartWare and SmartView Management Center are trademarks of Patton Electronics Company.
SmartNode 4830 Quick Start Guide Introduction This Quick Start Guide leads you through the basic steps to set up a new SmartNode (see figure 1) and to download a configuration. Please note that this guide does not replace the detailed Software Configuration Guide and the Getting Started Guide on the CD-ROM and available online at www.patton.com/voip. Figure 1. SmartNode product (SmartNode 4838 shown) SmartNodes can be used for a wide variety of IP and voice over IP applications.
SmartNode 4830 Quick Start Guide Connecting a PC, logging in, and configuring the LAN IP address Connecting power and configuring the default IP address Connect the SmartNode to the mains power supply using the included power supply and cable. When the RUN LED stops blinking and remains lit, the SmartNode is ready. The factory default IP settings are listed in table 1. If these addresses do not work with your network they must be changed.
SmartNode 4830 Quick Start Guide 3. Type administrator as the login prompt and press the Enter key after the password prompt (do not type anything for the password). A prompt will appear consisting of the IP address and > character. login:administrator password: 172.16.40.1> 4. Following log in, the SmartNode is in operator execution mode (indicated by > character in the command line prompt). With the commands enable and configure, you enter the configuration mode. 172.16.40.1>enable 172.16.40.
SmartNode 4830 Quick Start Guide Connecting the SmartNode to the LAN The 4830 Ethernet ports are auto MDX, therefore a straight-through wired cable can be used for host and switch connections (see figure 3).
SmartNode 4830 Quick Start Guide Note If your application is unique and not covered by any of Patton’s configuration templates, you can manually configure the SmartNode instead of loading a configuration file template. In that case, refer to the SmartNode Series SmartWare Software Configuration Guide for information on configuring the SmartNode device. In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the configuration named SN.
SmartNode 4830 Quick Start Guide Compliance EMC compliance: • FCC Part 15, Class A • EN55022, Class A • EN55024 Safety compliance: • UL60950-1/CSA C22.2 No.
SmartNode 4830 Quick Start Guide Disconnect all power before servicing. CAUTION The SmartNode product contains no user serviceable parts. CAUTION CAUTION The mains outlet that is utilized to power the equipment must be within 1 foot (3 meters) of the device and shall be easily accessible. FCC Part 68 (ACTA) Statement (FXO ports) This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA.
SmartNode 4830 Quick Start Guide nected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above condition may not prevent degradation of service in some situations.
SmartNode 4830 Quick Start Guide R&TTE 1999/5/EG Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige Anerkennung ihrer Konformität. \ Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten. Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem Gerät bestätigt.
SmartNode 4830 Quick Start Guide Authorized European Representative VoIPon www.voipon.co.uk sales@voipon.co.
