User Guide

ManualsBrandsPatton electronic ManualsSwitchIndustrial Ethernet Extender with LCD Interface 3231

Model 3231

Industrial Ethernet Extender with

LCD

CLI Reference Guide

Sales Ofﬁce:

+1 (301) 975-1000

Technical Support:

+1 (301) 975-1007

E-mail:

support@patton.com

WWW:

www.patton.com

Part Number:

07M3231-CLI, Rev. A

Revised:

October 29, 2008

Important

This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial

or residential environment.

Start Installation

For Quick

Summary of content (189 pages)

PAGE 1
For Quick Start Installation Model 3231 Industrial Ethernet Extender with LCD CLI Reference Guide Important This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial or residential environment. Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com Part Number: 07M3231-CLI, Rev.
PAGE 2
Patton Electronics, Inc. Trademark Statement All other trademarks presented in this document are the property of their respective owners. Copyright © 2008, Patton Electronics. All rights reserved. The information in this document is subject to change without notice. Patton assumes no liability for errors that may appear in this document.
PAGE 3
Summary Table of Contents 1 Alarm Commands ......................................................................................................................................... 13 2 Bridge Commands......................................................................................................................................... 18 3 CPE Config Commands ................................................................................................................................
PAGE 4
Table of Contents Summary Table of Contents ........................................................................................................................... 3 Table of Contents ........................................................................................................................................... 4 About this guide ........................................................................................................................................... 10 Audience..............
PAGE 5
Model 3231 CLI Reference Guide Table of Contents Example Output: ethernet list transports .........................................................................................................35 ethernet set transport .............................................................................................................................................36 ethernet show transport .........................................................................................................................
PAGE 6
Model 3231 CLI Reference Guide Table of Contents gshdsl set terminal .................................................................................................................................................71 gshdsl seta..............................................................................................................................................................72 gshdsl show..............................................................................................................
PAGE 7
Model 3231 CLI Reference Guide Table of Contents 10 Port Commands .......................................................................................................................................... 102 port ethernet........................................................................................................................................................103 port list...........................................................................................................................
PAGE 8
Model 3231 CLI Reference Guide Table of Contents 15 Security Commands .................................................................................................................................... 140 security add .........................................................................................................................................................141 security clear ......................................................................................................................
PAGE 9
Model 3231 CLI Reference Guide Table of Contents Example Output: system list openfiles bun ...................................................................................................167 Example Output: system list users .................................................................................................................168 system log...........................................................................................................................................................
PAGE 10
About this guide This guide describes commands for configuring the Patton Model 3231 Industrial Ethernet Extender with LCD. Note For general information regarding setting up, installing and operating the 3231, refer to the Getting Started Guide. Audience This guide is intended for administrators and operators. Structure • Chapter 1, "Alarm Commands" on page 13 describes commands for configuring alarms. • Chapter 2, “Bridge Commands” on page 18 describes commands for configuring the bridge.
PAGE 11
Model 3231 CLI Reference Guide Using the CLI The Model 3231 may be configured through the CLI, although basic settings should be configured through the LCD menu on the unit. Connect a PC and log in Use an RS-232/Ethernet cable and DB9-RJ45 adapter to connect a PC’s serial port to the 3231’s Console port (see figure 1).
PAGE 12
Model 3231 CLI Reference Guide Precautions Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you become aware of potential problems. Note A note presents additional information or interesting sidelights. The alert symbol and IMPORTANT heading calls attention to important information. IMPORTANT The alert symbol and CAUTION heading indicate a potential hazard. Strictly follow the instructions to avoid property damage.
PAGE 13
Chapter 1 Alarm Commands Chapter contents alarm all alarmStatus..............................................................................................................................................14 alarm set alarmSeverity.............................................................................................................................15 alarm set alarmStatus..................................................................................................................
PAGE 14
Model 3231 CLI Reference Guide 1 • Alarm Commands alarm all alarmStatus Set the alarm state for all alarms. Table 2. alarm all alarmStatus Command alarm all alarmStatus clear alarm all alarmStatus reset alarm all alarmStatus Explanation Set the alarm state to "clear" for all alarms. Does not clear the number of occurences and the time of the most recent occurrence. Set the alarm state to "clear" for all alarms. Clears the number of occurrences and the time of the most recent occurrence.
PAGE 15
Model 3231 CLI Reference Guide 1 • Alarm Commands alarm set alarmSeverity Set the index for the severity level of an alarm. Table 3. alarm set alarmSeverity Command Explanation alarm set alarm Severity Determine the level of importance for specific alarms.
PAGE 16
Model 3231 CLI Reference Guide 1 • Alarm Commands alarm set alarmStatus Set the index for the status level of an alarm. Table 4. alarm set alarmStatus Command Explanation alarm set alarm Status active Mark the alarm condition as a currently present alarm. alarm set alarm Status clear Clear a specific alarm. Does not clear the number of occurrences or the most recent occurrence.
PAGE 17
Model 3231 CLI Reference Guide 1 • Alarm Commands alarm show Show alarm status. Table 5. alarm show Command alarm show Explanation Show alarm status. Example Output: alarm show --> alarm show Current Box State: Major Alarm Table Alarm Active | ID | Alarm String | Severity | Time | Count --------|-----|------------------------|-----------------|-----------|-----| 1 | PP Over Threshold | Informational | 00:00:00s | 0 | 2 | NP Over Threshold | Informational | 00:00:00s | 0 | 3 | G.
PAGE 18
Chapter 2 Bridge Commands Chapter contents bridge add interface ...............................................................................................................................................19 bridge attach..........................................................................................................................................................20 bridge clear interfaces...........................................................................................................
PAGE 19
Model 3231 CLI Reference Guide 2 • Bridge Commands bridge add interface Add a named interface to the bridge. Table 6. bridge add interface Command bridge add interface bridge add interface Explanation Add a named interface to the bridge.
PAGE 20
Model 3231 CLI Reference Guide 2 • Bridge Commands bridge attach Attach existing transport to existing bridge interface. Table 7. bridge attach Command Explanation bridge attach Attach existing transport to existing bridge interface.
PAGE 21
Model 3231 CLI Reference Guide 2 • Bridge Commands bridge clear interfaces Remove all bridge interfaces. Table 8. bridge clear interfaces Command bridge clear interfaces bridge clear interfaces Explanation Remove all bridge interfaces.
PAGE 22
Model 3231 CLI Reference Guide 2 • Bridge Commands bridge delete interface Remove specific bridge interface. Table 9. bridge delete interface Command bridge delete interface bridge delete interface Explanation Remove specific bridge interface.
PAGE 23
Model 3231 CLI Reference Guide 2 • Bridge Commands bridge detach Detach a transport from a bridge interface. Table 10. bridge detach Command bridge detach bridge detach Explanation Detach a transport from a bridge interface.
PAGE 24
Model 3231 CLI Reference Guide 2 • Bridge Commands bridge list interfaces List bridge interfaces. Table 11. bridge list interfaces Command bridge list interfaces Explanation List bridge interfaces.
PAGE 25
Model 3231 CLI Reference Guide 2 • Bridge Commands bridge set Configure bridge attributes. Table 12. bridge set Command Explanation bridge set dhcpFilteredPort bridge set dhcpMACFiltering disable enable Set the DHCP filtered port. Disable DHCP MAC filtering. Enable DHCP MAC filtering. bridge set filterage Set the time of no activity after which MAC addresses are removed from the filter table.
PAGE 26
Model 3231 CLI Reference Guide 2 • Bridge Commands bridge show Display bridge/interface settings. Table 13. bridge show Command bridge show bridge show interface Explanation Display bridge/interface settings. Display named interface settings. Example Output: bridge show --> bridge show Global bridge configuration: Filter age: 300 DHCP MAC Filtering: false DHCP Filtered Port: bun/port=ethernet Spanning bridge configuration: Spanning: Priority: Forward delay: Hello time: Max.
PAGE 27
Chapter 3 CPE Config Commands Chapter contents cpeconfig action.....................................................................................................................................................28 cpeconfig set ..........................................................................................................................................................29 cpeconfig show .............................................................................................................
PAGE 28
Model 3231 CLI Reference Guide 3 • CPE Config Commands cpeconfig action Note This command is only available on the CO unit. Refer to the Getting Started Guide for more information. Transmit/receive the CPE configuration. Table 14. cpeconfig action Command Explanation cpeconfig action get Request CPE to send it's configuration. cpeconfig action set Command CPE to configure itself.
PAGE 29
Model 3231 CLI Reference Guide 3 • CPE Config Commands cpeconfig set Note This command is only available on the CO unit. Refer to the Getting Started Guide for more information. Set CPE configurable parameters. Table 15. cpeconfig set Command Explanation cpeconfig set defaultgw Set default GW as format: xxx.xxx.xxx.xxx cpeconfig set dslrateTS cpeconfig set ipaddress cpeconfig set netmask Set DSL data rate as n_64kbps. Set IP Address as format: xxx.xxx.
PAGE 30
Model 3231 CLI Reference Guide 3 • CPE Config Commands cpeconfig show Note This command is only available on the CO unit. Refer to the Getting Started Guide for more information. Show the CPE's configuration. Table 16. cpeconfig show Command cpeconfig show Explanation Show the CPE's configuration. Example Output: cpeconfig show --> cpeconfig show Configuration State: Initializing Timeslots: IP Address: Netmask: Default Gateway: cpeconfig show 36 192.168.200.10 255.255.255.0 0.0.0.
PAGE 31
Chapter 4 Ethernet Commands Chapter contents ethernet add transport ...........................................................................................................................................32 ethernet clear transports.........................................................................................................................................33 ethernet delete transport .............................................................................................................
PAGE 32
Model 3231 CLI Reference Guide 4 • Ethernet Commands ethernet add transport Create ethernet transport. Table 17. ethernet add transport Command Explanation ethernet add transport Create ethernet transport.
PAGE 33
Model 3231 CLI Reference Guide 4 • Ethernet Commands ethernet clear transports Remove all ethernet transports Table 18. ethernet clear transports Command ethernet clear transports ethernet clear transports Explanation Remove all ethernet transports.
PAGE 34
Model 3231 CLI Reference Guide 4 • Ethernet Commands ethernet delete transport Remove single ethernet transport. Table 19. ethernet delete transport Command ethernet delete transport ethernet delete transport Explanation Remove single ethernet transport.
PAGE 35
Model 3231 CLI Reference Guide 4 • Ethernet Commands ethernet list List ethernet ports and transports. Table 20. ethernet list Command ethernet list ports ethernet list transports Explanation List ports available to transport ethernet data. Show ethernet transports.
PAGE 36
Model 3231 CLI Reference Guide 4 • Ethernet Commands ethernet set transport Set port of an existing ethernet transport. Table 21. ethernet set transport Command Explanation ethernet set transport ethernetport Set the port to be used as a physical Ethernet port. ethernet set transport port Set the port that an existing Ethernet port uses to transport ethernet data.
PAGE 37
Model 3231 CLI Reference Guide 4 • Ethernet Commands ethernet show transport Display existing ethernet transport. Table 22. ethernet set transport Command ethernet show transport Explanation Display existing ethernet transport.
PAGE 38
Chapter 5 Firewall Commands Chapter contents firewall add policy..................................................................................................................................................39 firewall add portfilter .............................................................................................................................................40 firewall add validator ..........................................................................................................
PAGE 39
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall add policy Add a firewall policy. Table 23. firewall add policy Command firewall add policy dmz-internal firewall add policy external-dmz Explanation Add a firewall policy between the DMZ interface and the internal interface. allowonly-val Allow only traffic to and/or from the IP address set in the firewall add validator command.
PAGE 40
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall add portfilter Add a port filter to a firewall policy. Note Begin each top-level command in the table below with firewall add portfilter . Table 24. firewall add portfilter Command ftp Explanation both Allow inbound/outbound transport of FTP packets between inside and outside interfaces. Allow transport of FTP packets from an outside interface to an inside interface.
PAGE 41
Model 3231 CLI Reference Guide 5 • Firewall Commands Table 24. firewall add portfilter Command smtp Explanation both inbound outbound tcp both inbound outbound telnet both inbound outbound udp both inbound outbound firewall add portfilter Allow inbound/outbound transport of SMTP packets between inside and outside interfaces Allow transport of SMTP packets from an outside interface to an inside interface.
PAGE 42
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall add validator Add a validator to a firewall policy. Note Begin each top-level command in the table below with firewall add validator . Table 25. firewall add validator Command Explanation both Filter inbound and outbound traffic based on IP addresses. inbound outbound Block incoming traffic based on IP addresses.
PAGE 43
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall clear Delete all firewall policies or portfilters from an existing configuration. Table 26. firewall clear Command firewall clear policies firewall clear portfilters firewall clear Explanation Delete all exisiting policies from the firewall configuration. Delete all portfilters that were added to an existing firewall policy using the firewall add portfilter command.
PAGE 44
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall delete Delete a firewall policy or portfilter from an existing configuration Table 27. firewall delete Command Explanation firewall delete policy Delete a specific existing policy from the firewall configuration. firewall delete portfilter Delete a specific existing portfilter from the firewall configuration. firewall delete validator Delete a specific existing validator from a named policy.
PAGE 45
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall disable Disable firewall features. Table 28. firewall disable Command firewall firewall firewall firewall disable disable IDS disable blockinglog disable intrusionlog firewall disable sessionlog firewall disable Explanation Disable Disable Disable Disable all firewall features. IDS features of the firewall. logging of firewall blocking. logging of firewall intruders. Disable logging of firewall sessions.
PAGE 46
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall enable Enable firewall features. Table 29. firewall enable Command firewall firewall firewall firewall enable enable IDS enable blockinglog enable intrusionlog firewall enable sessionlog firewall enable Explanation Enable Enable Enable Enable all firewall features. IDS features of the firewall. logging of firewall blocking. logging of firewall intruders. Enable logging of firewall sessions.
PAGE 47
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall list Show information about specific firewall features. Table 30. firewall list Command firewall list policies firewall list portfilters firewall list protocol firewall list validators Explanation Show information about policies that were added to the firewall. Show information about portfilters that were added to a firewall policy. List the port numbers assigned to various protocols as given in RFC 1700.
PAGE 48
Model 3231 CLI Reference Guide 5 • Firewall Commands Example Output: firewall list protocol --> firewall list protocol Assigned Internet Protocol Numbers see RFC 1700 "Assigned Numbers" section "Protocol Numbers" pages 7 - 9 1 2 3 4 6 8 9 17 46 47 89 92 94 ICMP IGMP GGP IP TCP EGP IGP UDP RSVP GRE OSPFIGP MTP IPIP Internet Control Message Internet Group Management Gateway-to-Gateway IP in IP (encapsulation) Transmission Control Exterior Gateway Protocol any private interior gateway User Datagram Reserva
PAGE 49
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall set IDS Configure the firewall Intrusion Detection Service (IDS) feature. Table 31. firewall set IDS Command firewall set IDS DOSattackblock Explanation Set the length of time (in seconds) that the firewall blocks suspicious hosts for once a DOS attack attempt has been detected by the firewall.
PAGE 50
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall set securitylevel Set the desired level of security for the firewall. Table 32. firewall set securitylevel Command firewall set securitylevel Explanation high low Use a high level of firewall security between interfaces. Use a low level of firewall security between interfaces. medium Use a medium level of firewall security between interfaces. none Block all IP traffic for every security interface.
PAGE 51
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall set validator Configure the settings for a validator. Note Begin each top-level command in the table below with firewall set validator . Table 33. firewall set validator Command Explanation disabled Disable a validator that has been added to a policy. This allows it to be temporarily disabled without forcing the user to delete and then recreate it. This could be useful in a testing scenario.
PAGE 52
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall show Display information about a firewall setting. Table 34. firewall show Command Explanation firewall show IDS blacklist Show the hosts that are currently blacklisted by the intrusion detection system. firewall show policy Display information about a specific policy that was added to the firewall. firewall show portfilter Display information about a specific portfilter that was added to a firewall policy.
PAGE 53
Model 3231 CLI Reference Guide 5 • Firewall Commands Example Output: firewall show portfilter hei_http pex_in --> firewall show portfilter hei_http pex_in Firewall Port Filter: hei_http Transport type: Port number start: Port number end: Inbound permission: Outbound permission: Raw IP: TCP permission: UDP permission: 6 80 80 false true false true false Example Output: firewall show validator item0 pdmz_in --> firewall show validator item0 pdmz_in Firewall Host Validator: item0 Direction: both Host IP: 1
PAGE 54
Model 3231 CLI Reference Guide 5 • Firewall Commands firewall status Display information about the firewall security level and logging status. Table 35. firewall status Command firewall status Explanation Display information about the firewall security level and logging status. Example Output: firewall status --> firewall status Firewall enabled. Firewall security level: high. Firewall session logging enabled. Firewall blocking logging enabled. Firewall intrusion logging disabled.
PAGE 55
Chapter 6 G.SHDSL Commands Chapter contents gshdsl set BERMeterMode ....................................................................................................................................56 gshdsl set Clocking ................................................................................................................................................57 gshdsl set EthLinkKill......................................................................................................................
PAGE 56
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set BERMeterMode Configure patetrn generation Table 36. gshdsl set BERMeterMode Command gshdsl set BERMeterMode 511 gshdsl set BERMeterMode 511E gshdsl set BERMeterMode off gshdsl set BERMeterMode Explanation Configure pattern generation mode. Configure pattern generation mode that inserts errors into the pattern every two seconds. Disable pattern generation/detection.
PAGE 57
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set Clocking Configure clock mode. Table 37. gshdsl set Clocking Command gshdsl set Clocking central_internal gshdsl set Clocking remote_receive_recover gshdsl set Clocking Explanation DSL clock is provided by the unit; Set the unit as CO. Recover clock from DSL; Set the unit as CPE.
PAGE 58
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set EthLinkKill Configure the EthLinkKill feature. Table 38. gshdsl set EthLinkKill Command gshdsl set EthLinkKill disable gshdsl set EthLinkKill enable gshdsl set EthLinkKill Explanation Disable EthLinkKill feature. Disconnect the Ethernet link if the DSL link is down.
PAGE 59
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set LineProbe Configure the line probe feature. Table 39. gshdsl set LineProbe Command gshdsl set LineProbe disable gshdsl set LineProbe enable gshdsl set LineProbe Explanation Disable Line Probe feature. Find highest rate automatically that the line will support and set the DSL rate (up to 2.3 Mbps).
PAGE 60
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set action Save or shut down DSL configurations. Table 40. gshdsl set action Command gshdsl set action deactivate gshdsl set action start gshdsl set action Explanation Shut down the DSL port. Save DSL configuration changes; Always run after making changes to the DSL configuration.
PAGE 61
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set clockingcombination Configure clock mode. Table 41. gshdsl set clockingcombination Command gshdsl set clockingcombination central_internal gshdsl set clockingcombination remote_receive_recover gshdsl set clockingcombination Explanation DSL clock is provided by the unit; Set the unit as CO. Recover clock from DSL; Set the unit as CPE.
PAGE 62
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set datarateI Set I-bit of data rate. Table 42. gshdsl set datarateI Command gshdsl set datarateI gshdsl set datarateI Explanation Set I-bit of data rate (0-7).
PAGE 63
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set dslrateTS Set data rate. Table 43. gshdsl set dslrateTS Command gshdsl set dslrateTS gshdsl set dslrateTS Explanation Set data rate ( n times 64kbps).
PAGE 64
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set errMonIntervalCnt Set the number of intervals in error before the DSL link restarts. Table 44. gshdsl set errMonIntervalCnt Command gshdsl set errMonIntervalCnt gshdsl set errMonIntervalCnt Explanation Set the number of intervals in error before the DSL link restarts.
PAGE 65
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set errMonIntervalThreshold Set the number of allowable errors per interval. Table 45. gshdsl set errMonIntervalThreshold Command gshdsl set errMonIntervalThreshold gshdsl set errMonIntervalThreshold Explanation Set the number of allowable errors per interval.
PAGE 66
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set errMonIntervalTime Set the length in seconds of the current interval. Table 46. gshdsl set errMonIntervalTime Command gshdsl set errMonIntervalTime gshdsl set errMonIntervalTime Explanation Set the length in seconds of the current interval.
PAGE 67
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set errMonStartupDelay Set the amount of time to wait, after the link is up, before monitoring the DSL link. Table 47. gshdsl set errMonStartupDelay Command Explanation gshdsl set errMonStartupDelay Set the amount of time to wait, after the link is up, before monitoring the DSL link.
PAGE 68
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set errMonTotalIntervals Set the number of intervals to test before monitoring is disabled. Table 48. gshdsl set errMonTotalIntervals Command Explanation gshdsl set errMonTotalIntervals Set the number of intervals to test before monitoring is disabled.
PAGE 69
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set gshannex Set the annex for the dsl port. Table 49. gshdsl set gshannex Command gshdsl set gshannex AnnexA gshdsl set gshannex AnnexB gshdsl set gshannex Explanation Set Annex A for countries using T1. Set Annex B for countries using E1 or RFC1483.
PAGE 70
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set interface Set the interface for the dsl port. Table 50. gshdsl set interface Command gshdsl set interface atm gshdsl set interface hdlc gshdsl set interface Explanation Set when using pppoa. Set when using pppoh.
PAGE 71
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl set terminal Set the unit as a CO or a CPE. Table 51. gshdsl set terminal Command gshdsl set terminal central gshdsl set terminal remote gshdsl set terminal Explanation Set the unit as a CO. Set the unit as a CPE.
PAGE 72
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl seta Modify an attribute for G.SHDSL. Table 52. gshdsl seta Command gshdsl seta gshdsl seta Explanation Modify an attribute.
PAGE 73
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl show Display an atttribute for G.SHDSL. Table 53. gshdsl show Command Explanation gshdsl show gshdsl show Display all attributes. Display a specific attribute. Example Output: gshdsl show --> gshdsl show General Information: Version Platform Zip Wire Version Connected Modem State : : : : : 1.00 Unknown Software:4.2.
PAGE 74
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl showTestMode Display test mode information. Table 54. gshdsl showTestMode Command Explanation gshdsl showTestMode Display Loopback and BERT counters.
PAGE 75
Model 3231 CLI Reference Guide 6 • G.SHDSL Commands gshdsl showc Display error counters. Table 55. gshdsl showc Command Explanation gshdsl showc Display error counters.
PAGE 76
Chapter 7 Help Commands Chapter contents help .......................................................................................................................................................................
PAGE 77
Model 3231 CLI Reference Guide 7 • Help Commands help Display help menu. Table 56. help Command help help Explanation Display top-level help menu.
PAGE 78
Chapter 8 IP Commands Chapter contents ip add defaultroute ................................................................................................................................................79 ip add interface ......................................................................................................................................................80 ip add route .........................................................................................................................
PAGE 79
Model 3231 CLI Reference Guide 8 • IP Commands ip add defaultroute Configure default IP routes. Table 57. ip add defaultroute Command ip add defaultroute gateway ip add defaultroute interface ip add defaultroute Explanation Enter an IP address of the gateway that the route will use by default. Enter the name of the existing interface that the route will use.
PAGE 80
Model 3231 CLI Reference Guide 8 • IP Commands ip add interface Add an IP interface. Table 58. ip add interface Command Explanation ip add interface Add a named interface and set its IP address (optional).
PAGE 81
Model 3231 CLI Reference Guide 8 • IP Commands ip add route Add an IP route. Note Begin each top-level command in the table below with ip add route . Table 59. ip add route Command Explanation gateway Enter the IP address of the gateway that the route will use. interface Enter the name of the existing interface that the route will use.
PAGE 82
Model 3231 CLI Reference Guide 8 • IP Commands ip attach Add a transport to an IP interface. Table 60. ip attach Command ip attach ip attach Explanation Attach an existing transport to an existing IP interface.
PAGE 83
Model 3231 CLI Reference Guide 8 • IP Commands ip attachbridge Attach a bridge to the router. Table 61. ip attachbridge Command ip attachbridge ip attachbridge Explanation Attach the bridge to the router via an existing IP interface.
PAGE 84
Model 3231 CLI Reference Guide 8 • IP Commands ip attachvirtual Create a virtual interface. Table 62. ip attachvirtual Command Explanation ip attachvirtual Create a virtual interface that is associated with a "real" IP interface that has already been atatched to a transport.
PAGE 85
Model 3231 CLI Reference Guide 8 • IP Commands ip clear Clear attributes from an IP interface. Table 63. ip clear ip ip ip ip clear clear clear clear ip clear Command Explanation arpentries interfaces riproutes routes Clear all ARP entries listed in the IP ARP table. Clear all IP interfaces that were created. Delete all of the existing dynamic routes that have been obtained from RIP. Clear all static routes that were created.
PAGE 86
Model 3231 CLI Reference Guide 8 • IP Commands ip delete Delete an IP interface or route. Table 64. ip delete Command ip delete interface ip delete route ip delete Explanation Delete a specific IP interface. Delete a specific route.
PAGE 87
Model 3231 CLI Reference Guide 8 • IP Commands ip detach Detach a transport from an IP interface. Table 65. ip detach Command ip detach ip detach Explanation Detach a transport from an IP interface.
PAGE 88
Model 3231 CLI Reference Guide 8 • IP Commands ip interface Configure an IP interface. Note Begin each top-level command in the table below with ip interface . Table 66. ip interface Command add proxyarpentry Explanation proxyarpentry Configure proxy ARP functionality on an existing IP interface. Enter the netmask address of the interface. proxyarpexclusion Configure proxy ARP exclusion functionality on an existing IP interface.
PAGE 89
Model 3231 CLI Reference Guide 8 • IP Commands Example Output: ip interface ip1 list proxyarpentries --> ip interface ip1 list proxyarpentries Proxy ARP entries for interface: ip1 ID | IP Address | Netmask | Exclude -----|-----------------|-----------------|--------1 | 192.168.200.1 | 255.255.255.255 | false 2 | 192.168.200.2 | 255.255.255.
PAGE 90
Model 3231 CLI Reference Guide 8 • IP Commands ip list Display information for an IP address. Table 67. ip list Command ip list arpentries ip list connections Explanation ip list interfaces ip list riproutes Display ARP table information. Display a list of active TCP/UDP connections in use by applications running on the device. Display information about IP interfaces. Display information about the routes that have been obtained from RIP. ip list routes Display information about existing routes.
PAGE 91
Model 3231 CLI Reference Guide 8 • IP Commands Example Output: ip list interfaces --> ip list interfaces IP Interfaces: ID | Name | IP Address | DHCP | Transport -----|--------------|------------------|----------|---------------1 | ip1 | 192.168.200.
PAGE 92
Model 3231 CLI Reference Guide 8 • IP Commands ip ping Ping an IP address. Table 68. ip ping Command ip ping ip ping Explanation Excute Ping command to specified IP address.
PAGE 93
Model 3231 CLI Reference Guide 8 • IP Commands ip set interface Configure specific settings for an IP interface. Note Begin each top-level command in the table below with ip set interface . Table 69. ip set interface Command Explanation dhcp disabled enabled The interface does not use DHCP client information. The interface obtains its configuration information from the DHCP client.
PAGE 94
Model 3231 CLI Reference Guide 8 • IP Commands ip set rip Configure RIP settings for an IP interface. Table 70. ip set rip Command ip set rip advertisedefault authentication Explanation disabled enabled disabled enabled defaultroutecost hostroutes password poison ip set rip Disable advertisement of a default route. Enable RIP to advertise a default route with the cost metric set. Reject RIP v2 packets containing an authentication entry.
PAGE 95
Model 3231 CLI Reference Guide 8 • IP Commands ip set route Configure settings for an IP route. Note Begin each top-level command in the table below with ip set route . Table 71. ip set route Command cost destination gateway interface ip set route Explanation Set the number of hops counted as the cost of the route for a route previously created. Set the destination network address of a route previously created.
PAGE 96
Model 3231 CLI Reference Guide 8 • IP Commands ip show Display information for an IP interface. Table 72. ip show Command Explanation ip show ip show debuginfo ip show interface Display current RIP configuration and any other information global to the router. Display debugging information. Display information about a named interface. ip show route Display information about a named route. Example Output: ip show debuginfo --> ip show debuginfo Found IP stack.
PAGE 97
Model 3231 CLI Reference Guide 8 • IP Commands -----------------------Socket message pending queue count: 3 Compile time configuration: --------------------------QOS support: disabled Checksum forwarded packets: no Validate source addresses: no ATIC Layer 2: not present IPv6 support: not present Example Output: ip show interface ip1 --> ip show interface ip1 IP Interface: ip1 Ipaddr Mask MTU Dhcp : : : : 192.168.200.10 255.255.255.
PAGE 98
Model 3231 CLI Reference Guide 8 • IP Commands ip traceroute Start or stop a trace route process. Table 73. ip traceroute Command ip traceroute start ip traceroute start ip traceroute stop ip traceroute Explanation Start a trace route process. Input multiple parameters for a trace route as a string, i.e.: "-v 0.0.0.0". Cancel a route trace already in progress.
PAGE 99
Chapter 9 Logger Commands Chapter contents logger set .............................................................................................................................................................100 logger show..........................................................................................................................................................101 Example Output: logger show ..................................................................................................
PAGE 100
Model 3231 CLI Reference Guide 9 • Logger Commands logger set Configure syslog. Table 74. logger set Command logger logger logger logger set set set set logger set facility facility host host Explanation Set the "facility" attribute. Set the new value of "facility". Set the log host. Specify the host IP address.
PAGE 101
Model 3231 CLI Reference Guide 9 • Logger Commands logger show Display syslog information. Table 75. logger show Command logger show Explanation Show the syslog configuration. Example Output: logger show --> logger show version host ident facility logger show = 1.00 = 0.0.0.
PAGE 102
Chapter 10 Port Commands Chapter contents port ethernet........................................................................................................................................................103 port list................................................................................................................................................................104 Example Output: port list all ..................................................................................................
PAGE 103
Model 3231 CLI Reference Guide 10 • Port Commands port ethernet Configure the Ethernet port. Table 76. port ethernet Command port ethernet set 100BaseMode AutoNegotiation FullDuplexMode Reset port ethernet show port ethernet status port ethernet Explanation false true false Use 10Mbps Ethernet operation. Use 100Mbps Ethernet operation. Force operation specified by 100BaseMode and FullDuplexMode. true false true false true Allow speed/duplex negotiation. Use half duplex Ethernet operation.
PAGE 104
Model 3231 CLI Reference Guide 10 • Port Commands port list List ports and port types. Table 77. port list Command port port port port port list list list list list all atm ethernet hdlc Explanation List List List List List ports by type. all ports. all ports using atm. all ethernet ports. all ports using hdlc.
PAGE 105
Chapter 11 PPP Commands Chapter contents ppp add transport ................................................................................................................................................106 ppp clear transports .............................................................................................................................................107 ppp delete transport.......................................................................................................................
PAGE 106
Model 3231 CLI Reference Guide 11 • PPP Commands ppp add transport Add a PPP over HDLC (PPPoH) transport. Table 78. ppp add transport Command Explanation ppp add transport ppp add transport dialin Create PPPoH transport. Create PPPoH transport that accepts dialin connections. ppp add transport dialout Create PPPoH transport that performs dialout.
PAGE 107
Model 3231 CLI Reference Guide 11 • PPP Commands ppp clear transports Remove all PPPoH transports. Table 79. ppp clear transports Command ppp clear transports ppp clear transports Explanation Remove all PPPoH transports.
PAGE 108
Model 3231 CLI Reference Guide 11 • PPP Commands ppp delete transport Remove a single PPPoH transport. Table 80. ppp delete transport Command ppp delete transport ppp delete transport Explanation Remove a single PPPoH transport.
PAGE 109
Model 3231 CLI Reference Guide 11 • PPP Commands ppp list transports List existing PPPoH transports. Table 81. ppp list transports Command ppp list transports Explanation List existing PPPoH transports.
PAGE 110
Model 3231 CLI Reference Guide 11 • PPP Commands ppp set transport Configure properties for a PPPoH transport. Note Begin each top-level command in the table below with ppp set transport . Table 82. ppp set transport Command Explanation dialin Set an existing PPPoH transport to accept dialin connections. Set a PPPoH transport to perform dialout.
PAGE 111
Model 3231 CLI Reference Guide 11 • PPP Commands Table 82. ppp set transport Command lcpmaxfail lcpmaxterm localip mru password remotedns remoteip routemask specificroute disabled enabled subnetmask theylogin chap none pap username welogin auto chap none pap ppp set transport Explanation Set the LCP maximum fail number for an existing transport.
PAGE 112
Model 3231 CLI Reference Guide 11 • PPP Commands ppp show transport Display properties for a specific PPPoH transport. Table 83. ppp show transport Command Explanation ppp show transport Show a single PPPoH transport's properties.
PAGE 113
Chapter 12 PPPoA Commands Chapter contents pppoa add transport ............................................................................................................................................114 pppoa clear transports..........................................................................................................................................115 pppoa delete ................................................................................................................................
PAGE 114
Model 3231 CLI Reference Guide 12 • PPPoA Commands pppoa add transport Add a PPP over ATM (PPPoA) transport. Note Begin each top-level command in the table below with pppoa add transport . Table 84. pppoa add transport Command dialin pvc dialout pvc pppoa add transport Explanation Create PPPoA transport that accepts dialin connections. Create PPPoA transport that performs dialout.
PAGE 115
Model 3231 CLI Reference Guide 12 • PPPoA Commands pppoa clear transports Remove all PPPoA transports. Table 85. pppoa clear transports Command pppoa clear transports pppoa clear transports Explanation Remove all PPPoA transports.
PAGE 116
Model 3231 CLI Reference Guide 12 • PPPoA Commands pppoa delete Remove a single PPPoA transport. Table 86. pppoa delete Command pppoa delete pppoa delete Explanation Remove a single PPPoA transport.
PAGE 117
Model 3231 CLI Reference Guide 12 • PPPoA Commands pppoa list transports List existing PPPoA transports. Table 87. pppoa list transports Command pppoa list transports Explanation List existing PPPoA transports.
PAGE 118
Model 3231 CLI Reference Guide 12 • PPPoA Commands pppoa set transport Configure properties for a PPPoA transport. Note Begin each top-level command in the table below with pppoa set transport . Table 88.
PAGE 119
Model 3231 CLI Reference Guide 12 • PPPoA Commands Table 88.
PAGE 120
Model 3231 CLI Reference Guide 12 • PPPoA Commands Table 88. pppoa set transport Command qosclass abr cbr qfc ubr vbr vbrrt remotedns remoteip routemask scr specificroute disabled enabled subnetmask theylogin chap none pap username vci vpi pppoa set transport Explanation Set quality of service class as abr (Available Bit Rate) for the transport.
PAGE 121
Model 3231 CLI Reference Guide 12 • PPPoA Commands Table 88. pppoa set transport Command welogin auto chap none pap pppoa set transport Explanation The authentication protocol used by the remote PPP server is discovered and used. Set CHAP (Challenge Handshake Authentication Protocol); Server sends an authentication request to the remote user dialing in. No authentication method is used. Set PAP (Password Authentication Protocol); Server sends an authentication request to the remote user dialing in.
PAGE 122
Model 3231 CLI Reference Guide 12 • PPPoA Commands pppoa show transport Display properties for a specific PPPoA transport. Table 89. pppoa show transport Command Explanation pppoa show transport Show a single PPPoA transport's properties.
PAGE 123
Chapter 13 PPPoE Commands Chapter contents pppoe add transport.............................................................................................................................................124 pppoe clear transports..........................................................................................................................................125 pppoe delete transport ......................................................................................................................
PAGE 124
Model 3231 CLI Reference Guide 13 • PPPoE Commands pppoe add transport Add a PPP over Ethernet (PPPoE) transport. Note Begin each top-level command in the table below with pppoe add transport dialout. Table 90. pppoe add transport Command Explanation eth Create a PPPoE transport that performs dialout over Ethernet.
PAGE 125
Model 3231 CLI Reference Guide 13 • PPPoE Commands pppoe clear transports Remove all PPPoE transports. Table 91. pppoe clear transports Command pppoe clear transports pppoe clear transports Explanation Remove all PPPoE transports.
PAGE 126
Model 3231 CLI Reference Guide 13 • PPPoE Commands pppoe delete transport Remove a single PPPoE transport. Table 92. pppoe delete Command pppoe delete transport pppoe delete transport Explanation Remove a single PPPoE transport.
PAGE 127
Model 3231 CLI Reference Guide 13 • PPPoE Commands pppoe list transports List existing PPPoE transports. Table 93. pppoe list transports Command pppoe list transports Explanation List existing PPPoE transports.
PAGE 128
Model 3231 CLI Reference Guide 13 • PPPoE Commands pppoe set transport Configure properties for a PPPoE transport. Note Begin each top-level command in the table below with pppoe set transport . Table 94.
PAGE 129
Model 3231 CLI Reference Guide 13 • PPPoE Commands Table 94.
PAGE 130
Model 3231 CLI Reference Guide 13 • PPPoE Commands Table 94. pppoe set transport Command mcr password pcr port pvc qosclass abr cbr qfc ubr vbr vbrrt remotedns remoteip routemask scr pppoe set transport Explanation Set the minimum cell rate for an existing PPPoE transport (Applies only to existing PVC transports). Set a dial-out password on a named transport.
PAGE 131
Model 3231 CLI Reference Guide 13 • PPPoE Commands Table 94. pppoe set transport Command specificroute disabled enabled subnetmask theylogin chap none pap username vci vpi welogin auto chap none pap pppoe set transport Explanation Create a default route to the subnet at the remote end of the PPP link. Allow the created route to apply to packets for the subnet at the remote end of the PPP link.
PAGE 132
Model 3231 CLI Reference Guide 13 • PPPoE Commands pppoe show transport Display properties for a specific PPPoE transport. Table 95. pppoe show transport Command pppoe show transport pppoe show transport Explanation Show a single PPPoE transport's properties.
PAGE 133
Chapter 14 RFC1483 Commands Chapter contents rfc1483 add transport ..........................................................................................................................................134 rfc1483 clear transports .......................................................................................................................................135 rfc1483 delete transport...................................................................................................................
PAGE 134
Model 3231 CLI Reference Guide 14 • RFC1483 Commands rfc1483 add transport Create a new transport. Note Begin each top-level command in the table below with rfc1483 add transport . Table 96. rfc1483 add transport Command Explanation Create a named RFC1483 transport and specify the virtual path and virtual channel. Create a named RFC1483 transport that uses the Logical Link Control (LLC) encapsulation method.
PAGE 135
Model 3231 CLI Reference Guide 14 • RFC1483 Commands rfc1483 clear transports Remove all RFC1483 transports. Table 97. rfc1483 clear transports Command rfc1483 clear transports rfc1483 clear transports Explanation Remove all RFC1483 transports.
PAGE 136
Model 3231 CLI Reference Guide 14 • RFC1483 Commands rfc1483 delete transport Remove a single RFC1483 transport. Table 98. rfc1483 delete Command rfc1483 delete transport rfc1483 delete transport Explanation Remove a specified transport.
PAGE 137
Model 3231 CLI Reference Guide 14 • RFC1483 Commands rfc1483 list transports List existing RFC1483 transports. Table 99. rfc1483 list transports Command rfc1483 list transports Explanation List existing RFC1483 transports.
PAGE 138
Model 3231 CLI Reference Guide 14 • RFC1483 Commands rfc1483 set transport Configure properties for an RFC1483 transport. Note Begin each top-level command in the table below with rfc1483 set transport . Table 100. rfc1483 set transport Command bt mbs mcr mode llc pcr port qosclass rxvci rxvpi scr txvci txvpi vci vpi rfc1483 set transport Explanation Set burst tolerance. Set max. burst size. Set minimum cell rate.
PAGE 139
Model 3231 CLI Reference Guide 14 • RFC1483 Commands rfc1483 show transport Display properties for a specific RFC1483 transport. Table 101. rfc1483 show transport Command rfc1483 show transport Explanation Show a single RFC1483 transport's properties.
PAGE 140
Chapter 15 Security Commands Chapter contents security add .........................................................................................................................................................141 security clear ........................................................................................................................................................142 security delete .............................................................................................................
PAGE 141
Model 3231 CLI Reference Guide 15 • Security Commands security add Add security interfaces and triggers. Table 102. security add Command Explanation security add interface dmz external internal security add trigger netmeeting tcp udp security add Add DMZ interface. Add external interface. Add internal interface. Add a trigger to allow Netmeeting to transport through the security package.
PAGE 142
Model 3231 CLI Reference Guide 15 • Security Commands security clear Clear interfaces and triggers. Table 103. security clear Command security clear interfaces security clear triggers security clear Explanation Clear all interfaces. Clear all triggers.
PAGE 143
Model 3231 CLI Reference Guide 15 • Security Commands security delete Delete a specified interface or trigger. Table 104. security delete Command security delete interface security delete trigger security delete Explanation Delete specified interface. Delete specified trigger.
PAGE 144
Model 3231 CLI Reference Guide 15 • Security Commands security disable Disable security features. Table 105. security disable Command security disable security disable Explanation Disable security.
PAGE 145
Model 3231 CLI Reference Guide 15 • Security Commands security enable Enable security features. Table 106. security enable Command security enable security enable Explanation Enable security.
PAGE 146
Model 3231 CLI Reference Guide 15 • Security Commands security list List interfaces and triggers. Table 107. security list Command security list interfaces security list triggers Explanation List all interfaces. List all triggers.
PAGE 147
Model 3231 CLI Reference Guide 15 • Security Commands security set trigger Configure settings for security triggers. Note Begin each top-level command in the table below with security set trigger . Table 108. security set trigger Command Explanation UDPsessionchaining disable addressreplacement enable both binaryaddressreplacement endport maxactinterval multihost sessionchaining startport security set trigger Disable UDP session chaining on an existing trigger.
PAGE 148
Model 3231 CLI Reference Guide 15 • Security Commands security show Display information about a specific interface or trigger. Table 109. security show Command Explanation security show interface Display information about a specific interface that was added to the Security module. Display information about a specific trigger that was added to the Security module.
PAGE 149
Model 3231 CLI Reference Guide 15 • Security Commands security status Display information about all security features. Table 110. security status Command security status Explanation Display information about the security package including security status, firewall status, NAT status, and firewall logging. Example Output: security status --> security status Security enabled. Firewall enabled. Firewall security level: high. Firewall session logging enabled. Firewall blocking logging enabled.
PAGE 150
Chapter 16 SNMP Commands Chapter contents snmp add.............................................................................................................................................................151 snmp delete .........................................................................................................................................................152 snmp save ..........................................................................................................................
PAGE 151
Model 3231 CLI Reference Guide 16 • SNMP Commands snmp add Add community and trap entries. Table 111. snmp add Command snmp add community snmp add trap snmp add Explanation Add an entry to the Community Table. read Add an SNMP version 1 or 2 read-only community. The IP address can be used to limit access to a single host or it can be 0.0.0.0 to allow access from any host. write Add an SNMP version 1 or 2 read-write community.
PAGE 152
Model 3231 CLI Reference Guide 16 • SNMP Commands snmp delete Delete community and trap entries. Table 112. snmp delete Command Explanation snmp delete community snmp delete trap snmp delete Delete an entry from the Community Table. Index of the row to delete. Delete an entry from the Trap Table. Index of the row to delete.
PAGE 153
Model 3231 CLI Reference Guide 16 • SNMP Commands snmp save Save configuration. Note System Save is still required. Table 113. snmp save Command snmp save snmp save Explanation Save configuration.
PAGE 154
Model 3231 CLI Reference Guide 16 • SNMP Commands snmp set Configure SNMP properties. Note Begin each top-level command in the table below with snmp set. Table 114. snmp set Command community Explanation read sysContact sysDescr sysLocation sysName trap snmp set Add an entry to the Community Table. Add an SNMP version 1 or 2 readonly community. The IP address can be used to limit access to a single host or it can be 0.0.0.0 to allow access from any host.
PAGE 155
Model 3231 CLI Reference Guide 16 • SNMP Commands snmp show Display information for an SNMP configuration. Table 115. snmp show Command Explanation snmp show Show SNMP configuration. Example Output: snmp show --> snmp show Static Variables Sys Descr Sys Object ID Sys Location Sys Contact Sys Name Snmp Enable Authen Traps : : : : : : "not set" 1.3.6.1.4.1.1768.
PAGE 156
Chapter 17 Source Commands Chapter contents source ................................................................................................................................................
PAGE 157
Model 3231 CLI Reference Guide 17 • Source Commands source Read a file of commands. Table 116. source Command source source Explanation Read a file of commands.
PAGE 158
Chapter 18 System Commands Chapter contents system add ...........................................................................................................................................................159 system config .......................................................................................................................................................160 system cpu ......................................................................................................................
PAGE 159
Model 3231 CLI Reference Guide 18 • System Commands system add Add a user to the system. Table 117. system add Command system add login system add user system add Explanation Add Local user --- Authenticate is Disabled. Add an optional comment about the user that us displayed when you type the commands system list users and system list logins. Add Dialin user --- Authenticate is Enabled.
PAGE 160
Model 3231 CLI Reference Guide 18 • System Commands system config Manage the system configuration. Table 118. system config Command system config backup system config clear system config restore backup system config save system config Explanation Save system config as a backup file. Save the backup configuration on a webserver. Clear all configuration, only leaves superuser login. Revert to saved configuration. Restore the backup configuration from the file: //isfs/im.conf.backup.
PAGE 161
Model 3231 CLI Reference Guide 18 • System Commands system cpu Manage CPU usage statistics. Table 119. system cpu Command system cpu npOverThreshold system cpu npThreshold system cpu npUsage system cpu ppOverThreshold system cpu ppThreshold system cpu ppUsage Explanation Report if the current usage is at or above the NP (network processor) threshold. get Report NP (network processor) usage. set Set the percent usage at which the system will declare an alarm condition.
PAGE 162
Model 3231 CLI Reference Guide 18 • System Commands Example Output: system cpu ppThreshold get --> system cpu ppThreshold get PP Usage Threshold: 90% Example Output: system cpu ppUsage --> system cpu ppUsage PP Usage: 1% system cpu 162
PAGE 163
Model 3231 CLI Reference Guide 18 • System Commands system delete Remove system users. Table 120. system delete Command system delete login system delete user system delete Explanation Remove local user. Remove dialin user.
PAGE 164
Model 3231 CLI Reference Guide 18 • System Commands system ifTable reset Reset packet counters. Table 121. system ifTable reset Command system ifTable reset all system ifTable reset index system ifTable reset Explanation Reset the packet counters for all interfaces. Reset the packet counters for a particular interface.
PAGE 165
Model 3231 CLI Reference Guide 18 • System Commands system info Display hardware/software information. Table 122. system info Command system info Explanation Display hardware/software information. Example Output: system info --> system info Global System Configuration: Model Code : Software ver: Hardware ver: Kernal ver : Key ver : Build type : 3231 G.SHDSL Access Device 2.8.18 BSP Rev.B BSP:1.0 / He100/2xx CSP v2.3 8.2.0.
PAGE 166
Model 3231 CLI Reference Guide 18 • System Commands system legal Show copyright information. Table 123. system info Command system legal Explanation Show copyright information.
PAGE 167
Model 3231 CLI Reference Guide 18 • System Commands system list List system information. Table 124. system list Command system system system system list list list list Explanation errors logins openfiles users Display system error log. Display system users. List open file handles. Display system users.
PAGE 168
Model 3231 CLI Reference Guide 18 • System Commands Example Output: system list users --> system list users Users: May Authenticate Access ID | Name | Conf.
PAGE 169
Model 3231 CLI Reference Guide 18 • System Commands system log Set system logging options. Table 125. system log Command system system system system log log log log all disable enable entryexit system log info system log list system log nothing system log trace system log warnings Explanation Display all output. Disable module: upload/webserver/ip/rip Enable module: upload/webserver/ip/rip Display a message every time a function call is entered or left.
PAGE 170
Model 3231 CLI Reference Guide 18 • System Commands Example Output: system log list op --> system log list ip ip ip ip ip ip ip ip ip system log socket config arp rawip icmp udp tcp l2cyan (disabled) (disabled) (disabled) (disabled) (disabled) (disabled) (disabled) (disabled) 170
PAGE 171
Model 3231 CLI Reference Guide 18 • System Commands system restart Restart the system. This function acts the same as pressing the reset button. Table 126. system restart Command system restart system restart Explanation Restart the system.
PAGE 172
Model 3231 CLI Reference Guide 18 • System Commands system set Set user privileges. Note Begin each top-level command in the table below with system set. Table 127.
PAGE 173
Model 3231 CLI Reference Guide 18 • System Commands system show Display system information. Table 128. system show Command Explanation system show aticmem system show firmware update protection Show memory in use by ATIC global pool -- ATIC Memory diagnostics. Show Image Validation.
PAGE 174
Chapter 19 Transport Commands Chapter contents transports clear ....................................................................................................................................................175 transports delete...................................................................................................................................................176 transports list ................................................................................................................
PAGE 175
Model 3231 CLI Reference Guide 19 • Transport Commands transports clear Clear all transports. Table 129. transports clear Command transports clear transports clear Explanation Clear all transports.
PAGE 176
Model 3231 CLI Reference Guide 19 • Transport Commands transports delete Delete a specific transport. Table 130. transports delete Command transports delete transports delete Explanation Delete a specified transport.
PAGE 177
Model 3231 CLI Reference Guide 19 • Transport Commands transports list List all transports. Table 131. transports list Command transports list Explanation List all transports.
PAGE 178
Model 3231 CLI Reference Guide 19 • Transport Commands transports show Display information about a specific transport. Table 132. transports show Command Explanation transports show Show a specified transport.
PAGE 179
Chapter 20 User Commands Chapter contents user change..........................................................................................................................................................180 user logout...........................................................................................................................................................181 user password .....................................................................................................................
PAGE 180
Model 3231 CLI Reference Guide 20 • User Commands user change Switch users. Table 133. user change Command user change user change Explanation Switch user.
PAGE 181
Model 3231 CLI Reference Guide 20 • User Commands user logout Log out from the system. Table 134. user logout Command user logout user logout Explanation Log out from system.
PAGE 182
Model 3231 CLI Reference Guide 20 • User Commands user password Change a user’s password. Table 135. user password Command user password user password Explanation Change a current user's password.
PAGE 183
Chapter 21 Webserver Commands Chapter contents webserver clear.....................................................................................................................................................184 webserver disable .................................................................................................................................................185 webserver enable .................................................................................................................
PAGE 184
Model 3231 CLI Reference Guide 21 • Webserver Commands webserver clear Clear Web Server statistics. Table 136. webserver clear Command webserver clear statistics webserver clear stats webserver clear Explanation Clear Web Server statistics.
PAGE 185
Model 3231 CLI Reference Guide 21 • Webserver Commands webserver disable Disable the Web Server process. Table 137. webserver disable Command webserver disable webserver disable Explanation Disable the Web Server process.
PAGE 186
Model 3231 CLI Reference Guide 21 • Webserver Commands webserver enable Enable the Web Server process. Table 138. webserver enable Command webserver enable webserver enable Explanation Enable the Web Server process.
PAGE 187
Model 3231 CLI Reference Guide 21 • Webserver Commands webserver load Load derived archive for static content. Table 139. webserver load Command Explanation webserver load Load derived archive for static content.
PAGE 188
Model 3231 CLI Reference Guide 21 • Webserver Commands webserver set Configure the Web Server settings. Table 140. webserver set Command webserver set webserver set Explanation interface Existing IP interface over which to communicate. managementip Restrict webserver access to a single IP (0.0.0.0 for any IP). port Set an HTTP port. upnpport Set a Universal Plug and Play port.
PAGE 189
Model 3231 CLI Reference Guide 21 • Webserver Commands webserver show Display information about the Web Server. Table 141. webserver show Command Explanation webserver show info webserver show stats Display information about the Web Server process. Display information about how many bytes have been transmitted and received by the Web Server.